H3C WA Series Command Reference Manual

H3C WA Series WLAN Access Points

WLAN Command Reference

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document Version: 6W100-20100910

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Preface

The H3C WA documentation set includes 10 command references, which describe the commands and

command syntax options available for the H3C WA series WLAN access points.

The WLAN Command Reference describes WLAN interface, WLAN service, WLAN security, WLAN

RRM, WLAN IDS, WLAN QoS, and WDS configuration commands.

This preface includes:

z Audience

z Conventions

z About the H3C WA Documentation Set

z Obtaining Documentation

z Documentation Feedback

Audience

This documentation is intended for:

z Network planners

z Field technical support and servicing engineers

z Network administrators working with the WA series

Conventions

This section describes the conventions used in this documentation.

Command conventions

Convention Description

Boldface Bold

text represents commands and keywords that you enter literally as shown.

italic

Italic text represents arguments that you replace with actual values.

[ ]

Square brackets enclose syntax choices (keywords or arguments) that are

optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars,

from which you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical

bars, from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by

vertical bars, from which you select at least one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by

vertical bars, from which you may select multiple choices or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&)

sign can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface.

For example, the

New User

window appears; click

OK

.

>

Multi-level menus are separated by angle brackets. For example,

File

>

Create

>

Folder

.

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause bodily

injury.

Means reader be careful. Improper operation may cause data loss or damage to

equipment.

Means an action or information that needs special attention to ensure

successful configuration or good performance.

Means a complementary description.

Means techniques helpful for you to make configuration with ease.

About the H3C WA Documentation Set

The H3C WA documentation set includes:

Category Documents Purposes

Marketing brochures Describe product specifications and benefits.

Product

description and

specifications

Technology white papers

Provide an in-depth description of software features and

technologies.

Compliance and safety

manual

Provides regulatory information and the safety instructions

that must be followed during installation.

Quick start

Guides you through initial installation and setup procedures to

help you quickly set up and use your AP with the minimum

configuration.

Hardware

specifications

and installation

Installation guide

Guides you through hardware specifications and installation

methods to help you install your AP.

Getting started guide

Guides you through the main functions of your AP, and

describes how to install and log in to your AP, perform basic

configurations, maintain software, and troubleshoot your AP.

Configuration guides Describe software features and configuration procedures.

Software

configuration

Command references Provide a quick reference to all available commands.

User FAQ

Provides answers to some of the most frequently asked

questions on how to troubleshoot your AP.

Operations and

maintenance

Release notes

Provide information about the product release, including the

version history, hardware and software compatibility matrix,

version upgrade information, technical support information,

and software upgrading.

Obtaining Documentation

You can access the most up-to-date H3C product documentation on the World Wide Web at

http://www.h3c.com.

Click the links on the top navigation bar to obtain different categories of product documentation:

[Technical Support & Documents > Technical Documents] – Provides hardware installation, software

upgrading, getting started, and software feature configuration and maintenance documentation.

[Products & Solutions] – Provides information about products and technologies, as well as solutions.

[Technical Support & Documents > Software Download] – Provides the documentation released with

the software version.

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

i

Table of Contents

1 Applicable Models and Software Versions·····························································································1-1

2 Feature Matrix············································································································································2-1

3 Command/Parameter Matrix·····················································································································3-1

4 WLAN Interface Configuration Commands·····························································································4-1

WLAN Interface Configuration Commands·····························································································4-1

description·······································································································································4-1

display interface wlan-bss ···············································································································4-2

display interface wlan-mesh············································································································4-3

display interface wlan-radio·············································································································4-4

interface wlan-bss····························································································································4-6

interface wlan-mesh ························································································································4-7

interface wlan-radio·························································································································4-7

shutdown (WLAN-Radio interface view)··························································································4-8

shutdown (WLAN-BSS interface view)····························································································4-8

5 WLAN Security Configuration Commands·····························································································5-1

authentication-method·····················································································································5-1

cipher-suite······································································································································5-2

gtk-rekey client-offline enable··········································································································5-2

gtk-rekey enable······························································································································5-3

gtk-rekey method·····························································································································5-4

ptk-lifetime·······································································································································5-5

security-ie········································································································································5-5

tkip-cm-time·····································································································································5-6

wep default-key ·······························································································································5-6

wep key-id ·······································································································································5-7

wep mode········································································································································5-8

6 WLAN RRM Configuration Commands ···································································································6-1

autochannel-set avoid-dot11h·········································································································6-1

display wlan rrm·······························································································································6-1

dot11a··············································································································································6-3

dot11b··············································································································································6-4

dot11g··············································································································································6-4

dot11g protection enable·················································································································6-5

dot11n mandatory maximum-mcs···································································································6-6

dot11n support maximum-mcs········································································································6-7

power-constraint······························································································································6-7

spectrum-management enable········································································································6-8

wlan rrm···········································································································································6-8

ii

7 WLAN IDS Configuration Commands······································································································7-1

WLAN Rouge AP Configuration Commands··························································································7-1

attack-detection enable ···················································································································7-1

display wlan ids history····················································································································7-2

display wlan ids statistics·················································································································7-3

wlan ids············································································································································7-4

reset wlan ids history·······················································································································7-5

reset wlan ids statistics····················································································································7-5

WLAN Frame Filtering Configuration Commands ··················································································7-6

display wlan blacklist·······················································································································7-6

display wlan whitelist·······················································································································7-7

dynamic-blacklist enable ·················································································································7-8

dynamic-blacklist lifetime·················································································································7-8

reset wlan dynamic-blacklist············································································································7-9

static-blacklist mac-address ············································································································7-9

whitelist mac-address····················································································································7-10

8 WLAN QoS Configuration Commands····································································································8-1

display wlan wmm ···························································································································8-1

reset wlan wmm·······························································································································8-6

wmm cac policy·······························································································································8-7

wmm edca radio······························································································································8-8

wmm edca client (ac-vo and ac-vi)··································································································8-9

wmm edca client (ac-be and ac-bk) ······························································································8-10

wmm enable··································································································································8-11

wmm svp map-ac ··························································································································8-12

9 WDS Configuration Commands···············································································································9-1

bind wlan-mesh ·······························································································································9-1

display wlan mesh-link·····················································································································9-1

display wlan mesh-profile················································································································9-2

display wlan mp-policy·····················································································································9-3

link-hold-rssi ····································································································································9-4

link-initiation enable·························································································································9-5

link-keep-alive··································································································································9-6

link-maximum-number·····················································································································9-6

link rate-mode··································································································································9-7

link-saturation-rssi ···························································································································9-7

mesh-id············································································································································9-8

mesh-profile·····································································································································9-8

mesh-profile enable·························································································································9-9

mesh peer-mac-address··················································································································9-9

mp-policy·······································································································································9-10

probe-request-interval ···················································································································9-11

wlan mesh-profile ··························································································································9-11

wlan mp-policy·······························································································································9-12

wlan uplink-interface mesh-link·····································································································9-12

iii

10 WLAN Service Configuration Commands···························································································10-1

a-mpdu enable·······························································································································10-1

a-msdu enable·······························································································································10-2

beacon ssid-hide ···························································································································10-2

beacon-interval······························································································································10-3

channel··········································································································································10-3

channel band-width ·······················································································································10-4

client dot11n-only ··························································································································10-5

client max-count ····························································································································10-5

display wlan client··························································································································10-6

display wlan service-template ·······································································································10-9

display wlan statistics··················································································································10-10

dtim··············································································································································10-12

fragment-threshold ······················································································································10-13

long-retry threshold······················································································································10-13

max-power···································································································································10-14

max-rx-duration ···························································································································10-14

preamble······································································································································10-15

radio-type·····································································································································10-16

reset wlan client···························································································································10-16

reset wlan statistics ·····················································································································10-17

rts-threshold·································································································································10-17

service-template (WLAN radio interface view)············································································10-18

service-template { disable | enable } (WLAN service template view)··········································10-18

short-gi enable·····························································································································10-19

short-retry threshold ····················································································································10-20

shutdown ·····································································································································10-20

ssid ··············································································································································10-21

wlan broadcast-probe reply·········································································································10-21

wlan client idle-timeout················································································································10-22

wlan client keep-alive ··················································································································10-22

wlan country-code ·······················································································································10-23

wlan service-template··················································································································10-26

wlan uplink-interface····················································································································10-26

11 Wireless User Isolation·························································································································11-1

l2fw wlan-client-isolation enable····································································································11-1

12 Index ·······················································································································································12-1

1-1

z The models listed in this document are not applicable to all regions. Please consult your local sales

office for the models applicable to your region.

z Read this chapter before using an H3C WA series WLAN access point.

1 Applicable Models and Software Versions

H3C WA series WLAN access points include the WA2200 series and WA2600 series. Table 1-1 shows

the applicable models and software versions.

Table 1-1 Applicable models and software versions

Series Model Software version

WA2210-AG

WA2200 series access

points (indoors)

WA2220-AG

WA2210X-G

WA2200 series

WA2200 series access

points (outdoors)

WA2220X-AG

R 1115

WA2610-AGN

WA2612-AGN

WA2600 series access

points (indoors)

WA2620-AGN

R 1106

WA2610E-AGN

WA2600 series

WA2600 series access

points (enhanced)

WA2620E-AGN

R 1109

2-1

2 Feature Matrix

z Support of the H3C WA series WLAN access points for features, commands and parameters may

vary by device model. See this document for more information.

z For information about feature support, see Table 2-1. For information about command and

parameter support, see

Table 3-1.

z The term AP in this document refers to common APs, wireless bridges, or mesh APs.

Table 2-1 Feature matrix

Document Feature WA2200 series WA2600 series

Fundamentals

Configuration Guide

HTTPS Not supported Supported

802.11n radio mode Not supported Supported

802.11n bandwidth mode Not supported Supported

WLAN Configuration

Guide

802.11n rate configuration Not supported Supported

Optical Ethernet interface

Supported on

WA2210X-G/WA2220X-

AG only

Not supported

Layer 2 – LAN

Switching

Configuration Guide

GE interface Not supported Supported

DHCP server configuration Not supported Supported

Layer 3 – IP Services

Configuration Guide

DHCPv6 configuration Not supported Supported

IGMP snooping configuration Not supported Supported

IP Multicast

Configuration Guide

MLD snooping configuration Not supported Supported

Security Configuration

Guide

SSH2.0 Not supported Supported

3-1

3 Command/Parameter Matrix

Table 3-1 Command/Parameter matrix

Document Module Command/Parameter WA2200 series WA2600 series

display ip https

Not supported Supported

ip https acl

Not supported Supported

ip https certificate

access-control-policy

Not supported Supported

Fundamentals

Command

Reference

HTTP commands

ip https enable

Not supported Supported

a-mpdu enable

Not supported Supported

a-msdu enable

Not supported Supported

channel band-width

Not supported Supported

client dot11n-only

Not supported Supported

preamble

{

long

|

short

}

Only APs that

support the

802.11b/g radio

mode support this

command.

Only APs that

support the

802.11b/g radio

mode support this

command.

radio-type

Keywords

dot11an

and

dot11gn

not

supported

Supported

WLAN service

commands

short-gi enable

Not supported Supported

dot11a

{

disabled-rate |

mandatory-rate |

supported-rate

} rate-value

Only APs that

support 802.11a

radio mode

support this

command.

Only APs that

support 802.11a

radio mode

support this

command.

dot11n mandatory

maximum-mcs

Not supported Supported

dot11n support

maximum-mcs

Not supported Supported

WLAN

Command

Reference

WLAN RRM

commands

power-constraint

Only APs that

support the

802.11a radio

mode support this

command.

Only APs that

support the

802.11a radio

mode support this

command.

3-2

Document Module Command/Parameter WA2200 series WA2600 series

The maximum

number of

broadcast packets

that can be

forwarded on an

Ethernet interface

per second

broadcast-suppression

{ ratio |

pps

max-pps }

pps

max-pps

ranges from 1 to

148810.

pps

max-pps

ranges from 1 to

1488100.

The maximum

number of multicast

packets allowed on

an Ethernet

interface per

second

multicast-suppression

{ ratio |

pps

max-pps }

pps

max-pps

ranges from 1 to

148810.

pps

max-pps

ranges from 1 to

1488100.

Layer 2 – LAN

Switching

Command

Reference

The maximum

number of unknown

unicast packets

allowed on an

Ethernet interface

per second

unicast-suppression

{ ratio

|

pps

max-pps }

pps

max-pps

ranges from 1 to

148810.

pps

max-pps

ranges from 1 to

1488100.

DHCP commands

DHCP server configuration

commands

Not supported Supported

display ipv6 dhcp client

[

interface

interface-type

interface-number ]

Not supported Supported

display ipv6 dhcp client

statistics

[

interface

interface-type

interface-number

]

Not supported Supported

display ipv6 dhcp duid

Not supported Supported

Layer 3 - IP

Services

Command

Reference

DHCPv6

commands

reset ipv6 dhcp client

statistics

[

interface

interface-type

interface-number

]

Not supported Supported

4-1

z The models listed in this document are not applicable to all regions. Please consult your local sales

office for the models applicable to your region.

z Support of the H3C WA series WLAN access points (APs) for commands may vary by AP model.

For more information, see Feature Matrix.

z The interface types and the number of interfaces vary by AP model.

4 WLAN Interface Configuration Commands

WLAN Interface Configuration Commands

description

Syntax

description text

undo description

View

WLAN-BSS interface view, WLAN-Radio interface view, WLAN mesh interface view

Default Level

2: System level

Parameters

text: Description of an interface, a string of 1 to 80 characters. Currently, the AP supports the following

types of characters or symbols: standard English characters (numbers and case-sensitive letters),

special English characters, spaces, and other characters or symbols that conform to the Unicode

standard.

4-2

z An interface description can be the mixture of English characters and other Unicode characters.

The mixed description cannot exceed the specified length.

z To use a type of Unicode characters or symbols in an interface description, install the

corresponding Input Method Editor (IME) and log in to the AP through remote login software that

supports this character type.

z Each Unicode character or symbol (non-English characters) takes the space of two regular

characters. When the length of a description string reaches or exceeds the maximum line width on

the terminal software, the software starts a new line, possibly breaking a Unicode character into

two parts. As a result, garbled characters may be displayed at the end of a line.

Description

Use the description command to set the description of the current interface.

Use the undo description command to restore the default.

By default, the description of an interface is interface-name + interface.

Examples

# Set the description of WLAN-Radio 1/0/1 to WLAN-Radio1.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] description WLAN-Radio1

display interface wlan-bss

Syntax

display interface wlan-bss [ interface-number ]

View

Any view

Default Level

1: Monitor level

Parameters

interface-number: Specifies an existing WLAN-BSS interface by its interface number.

Description

Use the display interface wlan-bss command to display information about the specified WLAN-BSS

interface or all WLAN-BSS interfaces.

Examples

# Display information about WLAN-BSS 1.

<Sysname> display interface wlan-bss 1

WLAN-BSS1 current state: DOWN

IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 000f-e2c0-0110

Description: WLAN-BSS1 Interface

4-3

PVID: 1

Port link-type: access

Tagged VLAN ID : none

Untagged VLAN ID : 1

Port priority: 0

Maximum client number: 64

Clients: 0 associating, 0 associated

Input (total) : 0 packets, 0 bytes

: 0 unicasts, 0 bytes

: 0 broadcasts, 0 bytes

Output (total): 0 packets, 0 bytes

: 0 unicasts, 0 bytes

: 0 broadcasts, 0 bytes

Table 4-1 display interface wlan-bss command output description

Field Description

WLAN-BSS1 current state Physical-layer link state of the interface

IP Packet Frame Type Encapsulation type of the frames that the interface sends out

Hardware Address MAC address of the frames that the interface sends out

Description Description of the interface

PVID Default VLAN ID of the interface

Port link-type Link type of the interface, which can only be access currently.

Tagged VLAN ID VLANs whose packets are sent by the interface with the VLAN tag.

Untagged VLAN ID

VLANs whose packets are sent by the interface with the VLAN tag

removed.

Port priority Priority of the interface.

Maximum client number Maximum number of clients allowed to access the interface.

Clients: 0 associating, 0 associated

Clients: the number of associating clients, and the number of

associated clients.

Input (total) : 0 packets, 0 bytes

: 0 unicasts, 0 bytes

: 0 broadcasts, 0 bytes

Statistics on packets received at the physical layer:

z The total number of packets, and the total number of bytes.

z The total number of unicast packets, and the total number of

unicast bytes.

z The total number of broadcast packets, and the total number of

broadcast bytes.

Output (total): 0 packets, 0 bytes

: 0 unicasts, 0 bytes

: 0 broadcasts, 0 bytes

Statistics on packets sent at the physical layer:

z The total number of packets, and the total number of bytes.

z The total number of unicast packets, and the total number of

unicast bytes.

z The total number of broadcast packets, and the total number of

broadcast bytes.

display interface wlan-mesh

Syntax

display interface wlan-mesh [ interface-number ]

4-4

View

Any view

Default Level

1. Monitor level

Parameters

interface-number: Specifies a WLAN mesh interface by its interface number. The specified interface

must be one already created.

Description

Use the display interface wlan-mesh command to display information about the specified WLAN

mesh interface or all WLAN mesh interfaces already created if no interface is specified.

Examples

# Display information about WLAN mesh interface 3.

<Sysname> display interface wlan-mesh 3

WLAN-MESH3 current state: DOWN

IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 000f-e2c0-0110

Description: WLAN-MESH3 Interface

PVID: 1

Port link-type: access

Tagged VLAN ID : none

Untagged VLAN ID : 1

For more details about the fields in the above output, see Table 4-1.

display interface wlan-radio

Syntax

display interface wlan-radio [ interface-number ]

View

Any view

Default Level

1: Monitor level

Parameters

interface-number: Displays information about the WLAN-Radio interface specified by interface-number,

which is an interface number.

Description

Use the display interface wlan-radio command to display information about the specified

WLAN-Radio interface or all WLAN-Radio interfaces.

Examples

# Display information about WLAN-Radio 1/0/1.

<Sysname> display interface wlan-radio 1/0/1

WLAN-Radio1/0/1 current state: UP

IP Packet Frame Type: PKTFMT_IEEE_802.11, Hardware Address: 000f-e2c0-0110

Description: WLAN-Radio1/0/1 Interface

4-5

Radio-type 11a, channel auto(157), power(dBm) 19 auto (4)

Received: 0 authentication frames, 0 association frames

Sent out: 0 authentication frames, 0 association frames

Stations: 0 associating, 0 associated

Input : 30007 packets, 1536614 bytes

: 13565 unicasts, 520774 bytes

: 16442 broadcasts, 1015840 bytes

: 0 fragmented

: 5687 discarded, 263913 bytes

: 0 duplicates, 3054 FCS errors

: 2 decryption errors

Output: 10002 packets, 1154819 bytes

: 10002 unicasts, 1154819 bytes

: 0 broadcasts, 0 bytes

: 0 fragmented

: 1686 discarded, 195145 bytes

: 0 failed RTS, 2813 failed ACK

: 8570 transmit retries, 2200 multiple transmit retries

Table 4-2 display interface wlan-radio command output description

Field Description

WLAN-Radio1/1 current state Physical-layer link state of the WLAN-Radio interface

IP Packet Frame Type Encapsulation type of the frames that the interface sends out

Hardware Address MAC address of the frames that the interface sends out

Description Description of the interface

Radio-type 11a Radio type of the interface

channel auto(157)

Channel used by the interface. The keyword

auto

means the

channel is automatically selected and 157 is the number of the

selected channel.

If the channel is manually selected, the field will be displayed in

the format of

channel

configured-channel.

Available channels depend on the country code and radio type.

power(dBm) 19 auto (4)

Transmit power of the interface (in dBm). The value 19 is the

transmit power configured by the user; auto indicates that the

actual power is different from that configured by the user; the

bracketed number, is the current transmission power, 4 dBm in

this sample output. (If spectrum management and power

constraint have been configured for the 802.11a bands, the

actual transmit power on the interface may be different from the

configured value, depending on the configuration of two

commands:

max-power

and

power-constraint

.) For more

information about the

max-power

command and the

power-constraint

command, see WLAN Service and WLAN

RRM in the WLAN Command Reference.

If the protocol being used is not 802.11a or the power constraint

function on the 802.11a frequencies is not configured even

though 802.11a is used, this field will be displayed as

power(dBm) configured-power.

Received: 0 authentication frames, 0

association frames

The number of received authentication frames, and the number

of received association frames.

Sent out: 0 authentication frames, 0

association frames

The number of sent authentication frames, and the number of

sent association frames.

4-6

Field Description

Stations: 0 associating, 0 associated

The number of associating stations, and the number of

associated stations.

Input : 5620 packets, 254801 bytes

: 0 unicasts, 0 bytes

: 5620 broadcasts, 254801 bytes

: 0 fragmented

: 0 discarded, 0 bytes

: 0 duplicates, 96 FCS errors

: 0 decryption errors

Statistics on packets received at the physical layer:

z The total number of packets, and the total number of bytes.

z The total number of unicast packets, and the total number of

unicast bytes.

z The total number of broadcast packets, and the total number

of broadcast bytes.

z The number of fragmented packets.

z The number of dropped packets, and the number of dropped

bytes.

z The number of received duplicate frames, and the number of

FCS errors.

z The number of decryption errors.

Output: 0 packets, 0 bytes

: 0 unicasts, 0 bytes

: 0 broadcasts, 0 bytes

: 0 fragmented

: 0 discarded, 0 bytes

: 0 failed RTS, 0 failed ACK

: 0 transmit retries, 0 multiple transmit

retries

Statistics on packets sent at the physical layer:

z The total number of packets, and the total number of bytes.

z The total number of unicast packets, and the total number of

unicast bytes.

z The total number of broadcast packets, and the total number

of broadcast bytes.

z The number of fragmented packets.

z The number of dropped packets, and the number of dropped

bytes.

z The number of RTS packets failing to be sent, and the

number of ACK packets failing to be sent.

z The number of retransmitted frames, and the number of

transmit retries.

interface wlan-bss

Syntax

interface wlan-bss interface-number

undo interface wlan-bss interface-number

View

System view

Default Level

2: System level

Parameters

interface-number: WLAN-BSS interface number, which ranges from 0 to 255.

Description

Use the interface wlan-bss command to enter WLAN-BSS interface view. If the WLAN-BSS interface

identified by the interface-number argument does not exist, this command creates the WLAN-BSS

interface first.

Use the undo interface wlan-bss command to remove a WLAN-BSS interface.

Examples

# Create WLAN-BSS interface 1.

4-7

<Sysname> system-view

[Sysname] interface wlan-bss 1

[Sysname-WLAN-BSS1]

interface wlan-mesh

Syntax

interface wlan-mesh interface-number

undo interface wlan-mesh interface-number

View

System view

Default Level

2. System level

Parameters

interface-number: Number of a WLAN mesh interface. The value range for this argument is 1 to 32.

Description

Use the interface wlan-mesh command to enter WLAN mesh interface view. If the specified WLAN

mesh interface does not exist, the command creates the WLAN mesh interface first.

Use the undo interface wlan-mesh command to delete the specified WLAN mesh interface.

Examples

# Create WLAN mesh interface 2 in system view.

<Sysname> system-view

[Sysname] interface wlan-mesh 2

[Sysname-WLAN-MESH2]

interface wlan-radio

Syntax

interface wlan-radio interface-number

View

System view

Default Level

2: System level

Parameters

interface-number: WLAN-Radio interface number.

Description

Use the interface wlan-radio command to enter WLAN-Radio interface view.

Examples

# Enter WLAN-Radio 1/0/1 interface view.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1]

4-8

shutdown (WLAN-Radio interface view)

Syntax

shutdown

undo shutdown

View

WLAN-Radio interface view

Default Level

2: System level

Parameters

None

Description

Use the shutdown command to shut down the current WLAN-Radio interface.

Use the undo shutdown command to bring up the current WLAN-Radio interface.

By default, a WLAN-Radio interface is up.

Examples

# Shut down the interface WLAN-Radio 1/0/1.

<Sysname>system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] shutdown

shutdown (WLAN-BSS interface view)

Syntax

shutdown

undo shutdown

View

WLAN-BSS interface view

Default Level

2: System level

Parameters

None

Description

Use the shutdown command to shut down the current WLAN-BSS interface.

Use the undo shutdown command to bring up the current WLAN-BSS interface.

By default, a WLAN-BSS interface is up.

After a WLAN-BSS interface is shut down, the connection between the interface and the wireless

device will be torn down.

Examples

# Shut down the interface WLAN-BSS 1.

Page is loading ...

H3C WA Series Command Reference Manual

Related papers

Other documents