Metabo SKN 50 Operating instructions

Brand: Metabo

Model: SKN 50

Category: Power tools

Type: Operating instructions

115 366 5369 / D/ENG/F/NL/IT/ES/DA/SV / 1001 - 1.2

Betriebs- und Wartungsanleitung für

Stauchkopfnagler SKN 50

Operating and Maintenance Instructions Finish Nailer SKN 50

Notice d’utilisation et d’entretien de la cloueuse SKN 50

Gebruikers- en onderhoudshandleiding van

tacker voor platkopnagels SKN 50

Istruzioni per l’uso e la manutenzione per

Dispositivo di chiodatura per chiodi a testa ricalcata SKN 50

Manual de servicio y mantenimiento para

Clavadora para clavos de cabeza perdida SKN 50

Betjenings- og servicevejledning for dykker SKN 50

Anvisningar för drift och skötsel av dyckertpistol SKN 50

ENG

1. Getting to Know Your Finish Nailer SKN 50

Item Description

1 Trigger lock

2 Air inlet

3 Trigger

4 Catch lever

5 Exhaust deflector

6 Depth adjustment

7 Magazine slide

8 Service shutter

9 View on magazine contents

ENG

Contents

1. Getting to Know Your

Finish Nailer SKN 50

2. Please Read First!

2.1 Specified conditions of

use

3. Safety Instructions

3.1 Regulations

3.2 Tool safety

3.3 Work safety

4. Initial Operation

5. Care and Maintenance

5.1 Care

5.2 Trouble shooting

6. Specifications

7. Standard Delivery

8. Accessories

2.1 Specified conditions of

use

This Finish Nailer is an air

powered tacker. It is well

suited for fastening glazing

beads and window bars,

decorative strips and skirting

boards. The nails can be

located at easily concealed

locations of glued compo-

nents. The Finish Nailer

features a contract trip, which

requires the gun tip to be

pressed down before a shot

can be triggered.

It is suitable for driving type

SKN finishing nails of 1.0 x

1.2 mm diameter and a

length of 15 - 50 mm.

● oxygen or fuel gas is not

used as power source for

air-powered tackers.

● connection to an air

supply line is only made

by means of a quick

coupler, and that the tool

is de-pressurised after

disconnection.

● for maintenance and

repairs only the genuine

spare parts listed in the

parts list shall be used.

● repair and maintenance

work is only carried out by

individuals authorised by

the equipment manufac-

turer or other competent

individuals, under obser-

vation of the information

given in the instructions.

As competent person is

regarded who possesses

sufficient knowledge in the

field of air-powered tackers,

obtained by vocational

training, schooling and work

experience, and who is

familiar with the applicable

legal regulations pertaining

to work safety and accident

prevention and the general

accepted technical rules to

such extent, that he/she is

capable of judging the state

of operating safety of

tackers.

3 Safety Instructions

3.1 Regulations

For portable tackers the

standard DIN 7259 (UVV34)

is applicable. This standard

requires, that:

● for tackers only the

fasteners specified in the

instructions shall be used

(see chapter „Specifica-

tions“).

● tackers shall only be

connected to air lines that

are controlled by a pres-

sure regulating device,

ensuring that the max.

permissible operating

pressure is not exceeded

by more than 10%.

● Read instructions before

commissioning, especi-

ally the safety instructions.

● If you notice transport

damage while unpacking,

notify your supplier

immediately. Do not

operate the air tool!

● Dispose of the packing in

an environmentally friend-

ly manner. Take to a pro-

per collecting point.

● Keep instructions for

future use.

● If you lend or sell this air

tool be sure to have the

instructions to go with it.

2. Please Read First

Take care to avoid working

pressures over 7 bar and

shots without fasteners in the

magazine.

The SKN 50 features a depth

adjustment (item 6), which

allows for adjusting the depth

the nails are driven in.

A faulty or not properly wor-

king tool must be discon-

nected from the pressurised

air source immediately and

presented to a competent

person for inspection. Dis-

connect tool from air supply

and empty the magazine

during extended work breaks

or when work is completed.

3.2Tool Safety

Air-powered tackers shall

only be operated and

serviced by persons having

been instructed in the

operation of such tools.

Keep out of the reach of

children.

Before every use check to

see that all safety and

triggering devices are

functioning properly. Also

check the tightness of all

screws and nuts. The tool

must not be modified, nor

shall any emergency repairs

or conversion be made.

Avoid damage or weakening

of the tool. Never dismount

or disable parts such as the

tool’s trigger.

4. Initial Operation

The tool must be discon-

nected from the air supply for

loading its magazine!

By pressing the catch lever

(item 4) the magazine is

unlocked and the magazine

slide (item 7) can be pulled

back. The nails can then be

loaded from the side. Push

magazine slide (item 7)

forward until it engages at the

catch lever.

Turn exhaust deflector (item

5) to desired position. Set the

working pressure to the

lowest recommended pres-

sure (4.0 bar). Connection to

the pressurised air source is

made by 6 mm flexible air

hose fitted with a quick

coupler. Set the tacker,

checked for proper functio-

ning, to the point the fastener

is to be driven and pull the

trigger (item 3).

The SKN 50 is fitted with a

protecting cap on the contact

trip, to prevent damage when

working planed or otherwise

finished surfaces. For special

applications the protecting

cap should be removed.

To access a nail jammed in

the tip, actuate the lever on

the side of the service shutter

(item 8) to open it, then

remove jammed nail.

Increase or decrease the

working pressure in 0.5 bar

increments, until the desired

result is achieved. The tacker

should be operated at the

lowest pressure possible.

3.3Work Safety

Never aim an operable

tacker against yourself or

other persons. When

working, hold the tacker in

such way that your head and

body will not be injured in the

event of possible recoil.

Never pull the trigger with the

nozzle in the air.

When the tacker is operable,

carry it at the handle only and

never with the trigger pulled.

When working, take care that

fasteners are not shot

through thin material and do

not slide off at corners or

edges.

Always wear safety glasses

and hearing protection when

working with a tacker.

5. Care and Maintenance

5.1Care

Observing the maintenance

instructions given here en-

sures a long service life and

trouble-free operation of this

quality product. Always dis-

connect from the pressurised

air supply when servicing.

For a lasting, trouble-free

operation daily cleaning and

periodic lubrication is in-

dispensable. Use only

special pneumatic oil (see

chapter „Accessories“).

Your choices for lubrication:

a) by mist oiler

A complete service unit

includes a mist oiler and is

fitted at the compressor.

b) by line oiler

A line oiler is installed on the

tool’s air inlet, which provides

the necessary oil for lubri-

cation.

O-rings damages or soiled.

Clean or replace O-rings, tighten

screws fully..

A. Air escapes between lid and housing:

Faults and possible causes Remedy

B. Fasteners are not driven all the way in:

Working pressure too low.

Cross section of air hose too small.

Tool not lubricated.

Increase air pressure in 0.5 bar

increments, until fasteners are

properly driven.

Min. 6 mm inner diameter required.

Clean parts and lubricate.

C. Fasteners are driven too far into the material:

Working pressure too high. Reduce working pressure in steps

of 0.5 bar.

D. Fasteners project or are bend:

Tool not held down firmly enough.

Hold down tool more firmly or increase

working pressure, if necessary.

Nail strip jams and will not advance fully

forward.

Open bayonet lock. Remove jammed

nails and properly load suitable

nails.

E. Driver jammed with nail strip

5.2Trouble shooting

c) manual lubrication

If neither a service unit nor a

line oiler exists in the pres-

surised air system, 3 -5 drops

of pneumatic oil must be

given into the air inlet before

each use.

● Store air tools in dry

rooms only.

6. Specifications

8. Accessories

7. Standard Delivery

SKN 50

Air consumption (per shot) 0,66 l

Working pressure 5 - max. 7 bar

Magazine capacity (staples/brads) 110 pcs.

Dimensions (LxWxH) 295x60x235 mm

Weight (w/o fasteners) 0.92 kg

A-weighted single-shot emission

sound power level (L

1s) 90 dB

A-weighted single-shot emission

sound power level (L

1s) 85 dB

Vibration 2.7 m/sec

Recommend inner air hose diameter 6 mm

Suitable finishing nails type SKN 15 - 50 mm long

Wire size 1.25 x 1.00 mm

Pressurised air required: clean and free of condensate,

with fine mist of oil

Compressor capacity: min. 50 l/min filling capacity

Recommended working pressure Max. working pressure set at regulator

or filter/pressure regulator max. 7 bar.

Finish Nailer SKN 50

1 Instruction manual

1 Blow moulded case

1 Safety glasses

1 bottle pneumatic oil

2 Allen keys

Finishing Nails

SKN 20 NK, length 20 mm (1.000 pcs.) Stock-no. 090 105 3723

SKN 25 NK, length 25 mm (1.000 pcs.) Stock-no. 090 105 3731

SKN 30 NK, length 30 mm (1.000 pcs.) Stock-no. 090 105 3740

SKN 35 NK, length 35 mm (1.000 pcs.) Stock-no. 090 105 3758

SKN 40 NK, length 40 mm (1.000 pcs.) Stock-no. 090 105 3766

SKN 45 NK, length 45 mm (1.000 pcs.) Stock-no. 090 105 3774

SKN 50 NK, length 50 mm (1.000 pcs.) Stock-no. 090 105 3782

Pneumatic oil for air tools, 0.5 l can Stock-no. 090 100 8540

Line oiler 1/4" Stock-no. 090 105 4584





Elektra Beckum AG,

Daimlerstraße 1, D-49716 Meppen

Tel.: +49-1803-333 456, Fax: +49-1803-333 457

Metabo Power Tools Pty. Ltd., 28 Laser Drive,

Rowville, 3178, Victoria, Australia,

Phone: 03 9764 1933, Fax: 03 9764 1958



Metabo UK Ltd., 25 Majestic Road, GB-SO 16 OYT

Tel.: +44-2380-732 000, Fax: +44-2380-747 500



Lurem MACHINES à BOIS,

Zone Industriell/BP 1, F-617000 Domfront

Tel.: +33-2-333 757 00, Fax: +33-2-333 720 70



Metabo Belgium, 19-23, t Hofveld 3-5,

B-1702 Groot Bijgaarden

Tél.: +32-2-467 32 10, Fax: +32-2-466 75 28,

e-meil: [email protected]



Metabo Nederland b. v.,

Keulschevaart 8, NL-3621 MX Breukelen,

Postbus 180, NL-3620 AD Breukelen,

Tel.: +31-3462-642 44, Fax: +31-3462-635 54,

e-mail: [email protected]



Metabo (Schweiz) AG, Kundendienst,

Lindaustrasse 17, 8317 Tagelswangen

Tel.: +41-52-354 34 44, Fax: +41-52-354 34 45,

e-mail: [email protected]

www.elektra-beckum.ch



Carlo Stechel & Figli S.R.L.,

Via Buozzi 22, I-20097 San Donato Milanese (MI)

Tel.: +39-02-556 001 11, Fax: +39-02-556 003 22,

e-mail: [email protected]



Herramientas Metabo, S.A.,

Polígono Ind. N°6, Parcela 16,

E-28935 Móstoles (Madrid)

Tel.: +34-91-616 57 67, Fax: +34-91-616 43 55,

e-mail: [email protected]

Kestra S.A. Soldadura,

Polg. Ind. La Ferreria, C.Del Treball, No. 19,

E- 08110 Montcada I Reixac,

Tel.: +34-935-750 030, Fax: +34-935-753 394



Bolas - Máquinas e Ferramentas de Qualidade, S.A.,

Rua 8, Lotes 8, 10, 12, P.O. Box 53,

P-7001 Évora-Codex

Tel.: +351-66-74 93 00, Fax: +351-66-74 93 09,

e-mail: [email protected]



Metabo Danmark A/S,

Marielundvej 48 C, DK-2730 Herlev

Tel.: +44-84-13 55, Fax: +44-84-86 04,

e-mail: [email protected]



Profilma-Import A/S,

Postboks 536 Nanset, Sophus Buggesvei 48,

N-3252 Larvik

Tlf.: +47-33-114 777, Fax: +47-33-114 108

HDF-Paulsson AB,

Box 525, Svaravaregatan 5, S-30180 Halmstad

Tel.: +46-35-154 400, Fax: +46-35-121 780



Nofa OY, P.O.Box 28,

Hannuksentie 1, FIN-02270 Espoo

Tel.: +358-9-804 851, Fax: +358-9-809 485

EB- Polska,

Spółka z o.o.J.V., ul. Gdyńska 28,

PL-73110 Stargard Szczeciński

Tel.: +48-91-578 47 72, Fax: +48

91-578 47 72

EB Nefro KFT,

Futo U. 70, HU-3508 Miskolc

Tel.: +36-46-362 264; +36-46-366 363,

+36-30-450 618, Fax: +36-46-362 761

)

Extra Industrial Goods,

Rr. Fadil Rada 88, AL-Tirana

Tel.: +355-42-330 62, Fax: +355-42-330 63

AS Mecro,

Peterburi tee 44, EST-11415 Tallinn

Tel.: +372-6-201 101, Fax: +372-6-201 112

ITA Ltd.,

Balakirevskij Pereulok 19, str. 1, RUS-Moscow

Tel.: +7-95-737 93 11; +7-95-737 93 12,

+7-95-737 93 13, Fax: +7-95-737 93 14,

e-mail: [email protected]

Metabo s.r.o.,

Kralovicka 544, CZ-25001 Brandys nad Labem

Tel.: +42-202-804 458, Fax: +42-202-804 456,

e-mail: [email protected],

Internet: http://www.metabo.cz

;

Remtech Spol. S.R.O.,

Vinice 293, SK-90021 Svaty Jur

Tel.: +42-1-744 971 981, Fax: +42-1-744 971 291

Agent Trade, S. C., S.R.L.,

Aleea Bran Nr. 2, BL. 92, P., Ap. 47,

RO- 751552 Bucuresli 4

Tel.: +40

13-217 445, Fax: +40-13-214 505



Dilex d.o.o.,

Orginceva ut. 17, SLO-51113 Ljublijana

Tel.: +386-61-168 16 20, Fax: +386-61-168 16 16

EB_Adr3B.fm

EB_Adr3B.fm Seite 2 Mittwoch, 21. März 2001 1:06 13

Metabo SKN 50 Operating instructions

Brand: Metabo

Model: SKN 50

Category: Power tools

Type: Operating instructions

Download PDF

report

Metabo SKN 50 Operating instructions

Metabo SKN 50 Operating instructions

Related papers

Other documents