Pulsar S98-CR - v1.1 Operating instructions

Brand: Pulsar

Model: S98-CR - v1.1

Type: Operating instructions

S98-CR

v1.1

The S98-CR 9-port switch for 8 IP cameras

in enclosure with recorder space

Edition: 3 from 22.02.2016

Supercedes the edition: 2 from 27.11.2015

EN**

Features:

 9 10/100 Mb/s ports

 8 PoE ports (data transfer and power supply)

 15,4W for each PoE port, supports devices complaint

with the IEEE802.3af standard

 Supports auto-learning and auto-aging of MAC

addresses (1K size)

 Recorder space of dimensions max 400x345x100mm

WxHxD

 LED indication

 Additional assembly elements (straps for

attaching the DVR in enclosure)

 Metal enclosure – color white RAL 9003

 warranty – 2 year from the production date

Example of use.

1. Technical description

1.1. General description.

The S98-CR is a complete kit to build the CCTV system based on IP cameras. The switch is placed in a metal enclosure

with recorder space.

Automatic detection of any devices powered in the PoE standard is enabled at the 1 – 8 ports of the switch. The UPLINK port is

used for connection of another network device. The LEDs at the front panel indicate the operation status (description in the table

below). The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a

separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access

point or router.

1.2 Block diagram.

Fig. 1. Block diagram.

1.3. Description of components and connectors.

Table 1. (see Fig. 2)

Element no.

(Fig. 2)

Description

[1]

Switch

[2]

Switch mode power supply for the switch 48VDC/2,5A/120W

[3]

Potentiometer adjusting the output voltage of the power supply (46÷52V)

[4]

LED light – power supply operation indication

[5]

F 6,3A / 250V fuse socket

[6]

Mounting brackets for cables

[7]

Space for the 48VDC/2,5A/120W power supply of the recorder (desktop type)

[8]

Power Socket of the 230V AC recorder

[9]

Recorder space of dimensions max 400x345x100mm WxHxD

[10]

Straps for attaching the DVR in enclosure

Fig. 2. The enclosure view.

Table 2. (See Fig.3)

Component No.

(Fig. 3)

Description

[1]

8 x PoE port (1÷8)

[2]

1 x UPLINK port

[3]

48VDC power supply socket

Fig. 3 The view switch'a.

1.4. Technical parameters (Table 3.)

Table 3.

Ports

9 10/100Mb/s ports (8 x PoE + 1 x UPLINK)

with connection speed auto-negotiation and MDI/MDIX Auto Cross)

PoE power supply

IEEE 802.3af (1÷8 ports), 48VDC / 15,4W at each port *

Protocols, Standards

IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP

Forwarding rate

10BASE-T: 14880pps/port

100BASE-TX: 148800pps/port

Bandwidth

1,6Gbps

Transmission method

Store-and-Forward

Optical indication of

operation

Switch power supply;

Link/Act;

PoE Status

Power supply

90 ÷ 264VAC 50÷60Hz / 2,5A 230VAC

Operating conditions

temperature -10°C ÷ 45°C,

relative humidity 5% - 90%, no condensation

Dimensions (W x H x D)

Switch: 190 x 28 x 115 [mm]

Enclosure: 540 x 440 x 110+14 [mm]

Enclosure

Steel plate, DC01 1,0mm color white RAL 9003

Closing

Cheese screw x 1 (at the front)

Notes

The enclosure does not adjoin the assembly surface so that cables can be led

Gross/Net weight

7,63/8,31kg

Protection class

EN 60950-1:2007

II (second)

Storage temperatur

-20°C ÷ 60°C

Declarations

* The given value of 15.4W per port is the maximum value. The total power consumption should not exceed 96W when all PoE ports are being used.

2. Installation

2.1. Installation procedure

1. The unit should be mounted by a qualified installer, holding relevant permits and licenses (applicable and required

for a given country) for 230V/AC interference and low-voltage installations.

2. The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal

relative humidity (RH=90% maximum, without condensation) and temperature from -10°C to +45°C.

3. The switch shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes

of the enclosure. The load balance should be done before installation Switcha. The given value of 15.4W per port

is the maximum value referring to a single output. The total power consumption should not exceed 96W when all

PoE ports are being used.The increased demand for power is particularly evident in the case of cameras with

heaters or infrared illuminators - when launching these features, the power consumption increases rapidly, which

may adversely affect the operation of the switch. The device is designed for a continuous operation and is not

equipped with a power-switch. Therefore, an appropriate overload protection in the power supply circuit should be

provided. Moreover, the user should be informed how to disconnect the power supply unit from the mains supply

(usually by assigning an appropriate fuse in the fuse box). The electrical system shall be made in accordance with

applicable standards and regulations.

2.2. Installation procedure

1. Before installation, make sure that the voltage in the 230V power-supply circuit is cut off.

2. Mount the PSU in a selected location and connect the wires.

3. Connect the power cables (~230V) to the L-N terminals of the power supply.

4. Connect the ground wire to the terminal marked by the earth symbol PE (power supply module connector). Use a

three-core cable (with a yellow and green PE protection wire) to make the connection. Lead the cables to the appropriate

terminals of the connection board through the insulating bushing.

5. Connect the power (~230V).

6. Connect the camera wires to the RJ45 connectors (PoE connectors).

7. Check the optical indication of the switch operation.

8. After installing and checking proper working, the enclosure can be closed

Connection schemes.

3. Operation indication.

OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY

GREEN LED LIGHT (Power)

Indication of the switch's

power supply

OFF – no power supply of the switch

ON – power supply on, normal operation

OPTICAL INDICATION AT THE PoE PORTS (1÷8)

DIODA LED ZIELONA (PoE)

Indication of the PoE power

supply

at the RJ45 ports

OFF- no power supply at the RJ45 port (the device is not connected or not compliant

with the IEEE802.3af standard)

ON – supply at the RJ45 port

Blinking – short-circuit or output overload

YELLOW LED LIGHT (LINK)

The connection status of LAN

devices, 10MB/s or 100Mb/s

and data transmission

OFF- no connection

ON - the device is connected ; 10Mb/s or 100Mb/s

Blinking – data transmission

OPTICAL INDICATION AT THE UPLINK PORT

GREEN LED LIGHT

OFF- no connection

ON – the device is connected ; 10Mb/s or 100Mb/s

YELLOW LED LIGHT (LINK)

The connection status of LAN

devices, 10MB/s or 100Mb/s

and data transmission

OFF- no data transmission

ON - the device is connected : 10Mb/s or 100Mb/s

Blinking – data transmission

WEEE LABEL

Waste electrical and electronic equipment must not be disposed of with normal household waste.

According to the European Union WEEE Directive, waste electrical and electronic equipment

should be disposed of separately from normal household waste.

GENERAL WARRANTY CONDITIONS

1. Pulsar (manufacturer) grants a two-year quality warranty for the equipment, starting from the production date.

2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (selected by the manufacturer) if the

malfunction is due to the manufacturer. It includes manufacturing or material defects, provided that such defects have been

reported within the warranty period (point.1).

3. The equipment subjected to warranty should be brought to the place of purchase or directly to the main office of the

manufacturer.

4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.

5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenience, however not

later that within 14 days from the delivery to the service centre of the manufacturer.

6. The repair period mentioned in point 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the

equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.

7. All the services are carried out at the service centre of the manufacturer, exclusively.

8. The warranty does not cover the defects of the equipment, resulting from:

- reasons beyond the manufacturer's control,

- mechanical damage,

- improper storage and transport,

- use that violates the operation manual or equipment’s intended use

- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,

- improper installation and configuration (failure to follow instruction).

9. The warranty is void in case of construction changes and repairs carried out by any unauthorized service center or in case of

damage or modifications to warranty stickers and serial numbers.

10. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the

wholesale prices suggested by the manufacturer on the day of purchase.

11. The manufacturer takes no responsibility for the defects that result from the damaging, malfunctioning or inability to operate

the equipment especially when resulting from failure to comply with the recommendations and requirements contained in the

manual.

Pulsar

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail: biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl, www.zasilacze.pl

Pulsar S98-CR - v1.1 Operating instructions

Pulsar S98-CR - v1.1 Operating instructions

Pulsar S98-CR - v1.1 Operating instructions

Related papers

Other documents