Pulsar S98 - v1.0 Operating instructions
- Category
- Network switches
- Type
- Operating instructions
Pulsar S98 - v1.0 is a 9-port PoE switch designed to power IP cameras compliant with the IEEE 802.3af standard. It features 8 PoE ports for data transfer and power supply, with a maximum power output of 15.4W per port. The switch also includes 1 UPLINK port for connecting to other network devices. Additional features include auto-learning and auto-aging of MAC addresses, LED indication for power, link, and PoE status, and a compact design for easy installation.
Pulsar S98 - v1.0 is a 9-port PoE switch designed to power IP cameras compliant with the IEEE 802.3af standard. It features 8 PoE ports for data transfer and power supply, with a maximum power output of 15.4W per port. The switch also includes 1 UPLINK port for connecting to other network devices. Additional features include auto-learning and auto-aging of MAC addresses, LED indication for power, link, and PoE status, and a compact design for easy installation.
1
S98
v1.0
The S98 9-port switch for 8 IP cameras
PL
Edition: 2 from 22.02.2016
Supercedes the edition: 1 from 01.09.2015
EN**
Features:
9 10/100 Mb/s ports
8 PoE ports (data transfer and power supply)
15,4W for each PoE port, supports devices complaint
with the IEEE802.3af standard
Supports auto-learning and auto-aging of MAC
addresses (1K size)
LED indication
The PSD 480250 48VDC/2,5A/120W max.
power supply desktop type included
Additional assembly elements
warranty – 2 year from the production date
Example of use.
1. Technical description
1.1. General description.
S98 is a 9-port PoE switch designed to supply IP cameras operating in IEEE 802.3af standard. Automatic detection of
any devices powered in the PoE standard is enabled at the 1 – 8 ports of the switch. The UPLINK port is used for connection of
another network device. The LEDs at the front panel indicate the operation status (description in the table below).
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a separate
power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access point or
router.
2
1.2 Block diagram.
Fig. 1. Block diagram.
1.3. Description of components and connectors.
Table 1. (see Fig.2)
Element no.
(Fig. 2)
Description
[1]
8 x PoE port (1÷8)
[2]
1 x UPLINK port
[3]
Power Socket of the 48VDC
Fig. 2 The view switch'a.
3
1.4. Technical parameters
Table 2.
Ports
9 10/100Mb/s ports (8 x PoE + 1 x UPLINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802.3af (1÷8 ports), 48VDC / 15,4W at each port *
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Forwarding rate
10BASE-T: 14880pps/port
100BASE-TX: 148800pps/port
Bandwidth
1,6Gbps
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply;
Link/Act;
PoE Status
Power supply
90 ÷ 264VAC 50÷60Hz / 2,5A 230VAC
the PSD 480250 48VDC/2,5A/120W max. power supply desktop type
Operating conditions
temperature -10°C ÷ 45°C,
relative humidity 5% - 90%, no condensation
Dimensions (W x H x D)
190 x 28 x 115 [mm]
Additional equipment
plate to be fixed surface
Net/gross weight
1,27/ 1,50kg
Protection class
EN 60950-1:2007
II (second)
Storage temperatur
-20°C ÷ 60°C
Declarations
CE
* The given value of 15.4W per port is the maximum value. The total power consumption should not exceed 96W when all PoE ports are being used.
2. Installation
2.1. Requirements
The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal
relative humidity (RH=90% maximum, without condensation) and temperature from -10°C to +45°C. Ensure the free flow
of air around the unit. The PSU shall work in a vertical position that guarantees sufficient convectional air-flow through
ventilating holes of the enclosure.
The load balance should be done before installation Switcha. The given value of 15.4W per port is the maximum
value referring to a single output. The total power consumption should not exceed 96W when all PoE ports are being
used. The increased demand for power is particularly evident in the case of cameras with heaters or infrared illuminators -
when launching these features, the power consumption increases rapidly, which may adversely affect the operation of the
switch. The device is designed for a continuous operation and is not equipped with a power-switch. Therefore, an
appropriate overload protection in the power supply circuit should be provided. The electrical system shall be made in
accordance with applicable standards and regulations.
2.2. Installation procedure
1. Connect switch to the PSD480250 48VDC power supply unit desktop type.
2. Connect the power supply to the AC 230V socket.
3. Connect the camera wires to the RJ45 connectors (PoE connectors).
4. Check the optical indication of switch operation (see Table 3).
4
Connection schemes.
5
3. Operation indication.
Table 3. Operation indication
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY
GREEN LED LIGHT (Power)
Indication of the switch's
power supply
OFF – no power supply of the switch
ON – power supply on, normal operation
OPTICAL INDICATION AT THE PoE PORTS (1÷8)
DIODA LED ZIELONA (PoE)
Indication of the PoE power
supply
at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant
with the IEEE802.3af standard)
ON – supply at the RJ45 port
Blinking – short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10MB/s or 100Mb/s
and data transmission
OFF- no connection
ON - the device is connected: 10Mb/s or 100Mb/s
Blinking – data transmission
OPTICAL INDICATION AT THE UPLINK PORT(9)
GREEN LED LIGHT
OFF- no connection
ON – the device is connected: 10Mb/s or 100Mb/s
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10MB/s or 100Mb/s
and data transmission
OFF- no data transmission
ON - the device is connected: 10Mb/s or 100Mb/s
Blinking – data transmission
6
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment
should be disposed of separately from normal household waste.
GENERAL WARRANTY CONDITIONS
1. Pulsar (manufacturer) grants a two-year quality warranty for the equipment, starting from the production date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (selected by the manufacturer) if the
malfunction is due to the manufacturer. It includes manufacturing or material defects, provided that such defects have been
reported within the warranty period (point.1).
3. The equipment subjected to warranty should be brought to the place of purchase or directly to the main office of the
manufacturer.
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenience, however not
later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in point 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the
equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.
7. All the services are carried out at the service centre of the manufacturer, exclusively.
8. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment’s intended use
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,
- improper installation and configuration (failure to follow instruction).
9. The warranty is void in case of construction changes and repairs carried out by any unauthorized service center or in case of
damage or modifications to warranty stickers and serial numbers.
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the
wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no responsibility for the defects that result from the damaging, malfunctioning or inability to operate
the equipment especially when resulting from failure to comply with the recommendations and requirements contained in the
manual.
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50
e-mail: biuro@pulsar.pl, sales@pulsar.pl
http:// www.pulsar.pl, www.zasilacze.pl
-
1
-
2
-
3
-
4
-
5
-
6
Pulsar S98 - v1.0 Operating instructions
- Category
- Network switches
- Type
- Operating instructions
Pulsar S98 - v1.0 is a 9-port PoE switch designed to power IP cameras compliant with the IEEE 802.3af standard. It features 8 PoE ports for data transfer and power supply, with a maximum power output of 15.4W per port. The switch also includes 1 UPLINK port for connecting to other network devices. Additional features include auto-learning and auto-aging of MAC addresses, LED indication for power, link, and PoE status, and a compact design for easy installation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Pulsar S98 - v1.0 Operating instructions
-
-
-
-
-
-
-
-
-