Extron electronic DDS 402 User manual

Brand: Extron electronic

Model: DDS 402

Category: Plasma TVs

Type: User manual

This manual is also suitable for

Extron Electronics Home Theater Screen DDS 402

DDS 402

Digital Display Scaler

68-555-01 Rev. D

01 05

This symbol is intended to alert the user of important operating and maintenance

(servicing) instructions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous

voltage within the product's enclosure that may present a risk of electric shock.

Caution

Read Instructions • Read and understand all safety and operating instructions before using the

equipment.

Retain Instructions • The safety instructions should be kept for future reference.

Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user

information.

Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment

manufacturer because they may be hazardous.

Warning

Power sources • This equipment should be operated only from the power source indicated on the

product. This equipment is intended to be used with a main power system with a grounded

(neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or

disable it.

Power disconnection • To remove power from the equipment safely, remove all power cords from

the rear of the equipment, or the desktop power module (if detachable), or from the power

source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to be stepped on or

pinched by items placed upon or against them.

Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts

inside. To prevent the risk of shock, do not attempt to service this equipment yourself because

opening or removing covers may expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to

prevent overheating of sensitive components inside. These openings must never be blocked by

other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only

with the same or equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturer's instructions.

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel

contient des instructions importantes concernant l’exploitation et la maintenance

(réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de

tensions dangereuses non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant

d’utiliser le matériel.

Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou

présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le

fabricant du matériel car cela risquerait de poser certains dangers.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur

l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant un fil de

terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité :

n’essayez pas de la contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous

les cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il

est amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que

personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des

objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un

technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin

d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces

opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions

et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à

empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais

être bloquées par des objets.

Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la batterie. Remplacer

uniquement avec une batterie du meme type ou d'un ype equivalent recommande par le

constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.

Safety Instructions • English

Consignes de Sécurité • Français

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen

Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung

(Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des

Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und

die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und

Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie

aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in

der Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom

Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben

werden. Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem

geerdeten (neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt

eine Sicherheitsfunktion dar. Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle

Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich

ist) oder aus der Wandsteckdose ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und

niemand darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden

können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal durchgeführt

werden. Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines

elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen

der Abdeckungen die Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese

zur Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen

niemals von anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie

verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch

vom Hersteller empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den

Herstelleranweisungen.

Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de

operación y mantenimiento (o cambio de partes) que se desean destacar en el

contenido de la documentación suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con

voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja

o alojamiento del producto, y que puedan representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar

el equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la

documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente

recomendados por el fabricante, ya que podrian implicar riesgos.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación

eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un

sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es

una medida de seguridad, no puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de

alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero

del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el

cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en

lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el

interior no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no

intentar personalmente la reparación/mantenimiento de este equipo, ya que al abrir o extraer las

tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el

sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir

con otros objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar

esta batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante.

Desachar las baterías usadas siguiendo las instrucciones del fabricante.

Instrucciones de seguridad • Español

Precautions

QS-1

Quick Start — DDS 402

Installation

Step 1

Turn off power to the DDS 402 and input and out-

put devices, and remove power cords from them.

Step 2

Install four rubber feet on the bottom of the

DDS 402, or mount the DDS to furniture or in a rack

(see figure on the bottom of this page).

Step 3

Attach input devices to the DDS.

Input 1: RGB with buffered local

monitor

Input 2: RGB or component

video

/R-Y

/B-Y

/R-Y

/B-Y

/HV

V H

/HV

/R-Y

/B-Y

/HV

RGBHV video

RGBS video

RGsB video Component video (R-Y, B-Y, Y)

/R-Y

/B-Y

/HV

Step 4

Attach output devices to the DDS 402.

Rear panel video outputs

RGB or HDTV component video

output (15HD)

RGB or HDTV component video output (6 BNCs)

RGBHV video

RGBS video

Component video (R-Y, B-Y, Y)

/R-Y

/B-Y

/R-Y

/B-Y

/R-Y

/B-Y

The two video output connectors, the 15HD

connector and the five BNC connectors, both

output the same video signal and the same

sync format.

Step 5

Plug the DDS 402 and input and output devices

into a grounded AC source, and turn on the input

and output devices. The figure on the following

page shows a typical application.

Step 6

Use the LCD menu screens (see the next page) or

RS-232 programming to configure the DDS 402.

See chapter 2 for installation, chapter 3 for front

panel operation, and chapters 4 and 5 for

RS-232 operation.

RGB

RGB/R-Y, B-Y, Y

2A MAX

100-240V 50-60Hz

REMOTE

RGB/HD R-Y, B-Y, Y

RGB/R-Y, B-Y, Y

RGB

RGB/R-Y, B-Y, Y

/RY

/B-Y

/RY

/B-Y

Rack-mount

Bracket

Quick Start — DDS 402, cont’d

QS-2

Typical DDS 402 Application

2A MAX

100-240V 50-60Hz

RS-232

RGB/HD R-Y, B-Y, Y

RGB/R-Y, B-Y, Y

RGB

RGB/R-Y, B-Y, Y

/R-Y

/B-Y

HVS

/R-Y

/B-Y

/HV

RS-232

Control

Projector

PC Computer

HD Camera

Plasma Display

DDS 402

DDS 402 Menu System

Default display cycle

Display Cycle

sec.

Extron

Power

60-426-01 Input #2 Horz. 00.00 kHz

Vert. 00.00 Hz

Output Rate

DDS 402 Version

RGB 1024 x 768 @ 60

Main menu

Display

Cycle

2 sec.

Power

2 sec.

10 sec.

1 2 43 5

Output

Configuration

Input

Configuration

Memory

Presets

Advanced

Configuration

Exit

Extron

60-426-01

DDS 402

Version

Input menu

Input video type

• RGB • Betacam 50

• YUVi • Betacam 60

• YUVp • HDTV

The selected input is

also available for the

pixel phase adjustment

(next screen).

Use either Adjust

knob to set the

slected output’s

pixel phase.

Display

Cycle

Input #2

Betacam 50

NEXTNext

Input

Configuration

1 2

Input #2 Phase

016

QS-3

Output menu

NEXT NEXT

Scaler output resolutions

See the table below for

available combinations of

resolutions and refresh rates.

Default: 1024x768, 60 Hz

Scaler output frequencies

NOTE Lock = Accu-RATE

Frame Lock™

Output signal format

• RGB

• Y, R-Y, B-Y

Polarity combinations

• H-/V- (default)

• H-/V+

• H+/V-

• H+/V+

Output Signal

RGB

Sync Polarity

H Neg V Neg

Resol 1024 x 768

Refresh @ 60

Output

Configuration

Input

Configuration

noituloseR zH05 zH65 zH06 zH57 zH58 *zH06/05takcoL

084x046X XX X

006x008 X X X X

426x238XXX

084x848 X X

084x258XX

867x4201 X X X X X

867x0821X X

4201x0821 X X X

567x0631XX

4201x5631 X X

0501x0041X X X

p675 X X

p027ylnozH06@VTDHX X

p0801 ylnozH06@VTDH X X

i0801X X X

.tupniehtnodesab,detceles-otuasietartuptuoehT*

Memory Presets menu

Use either Adjust knob to adjust

the settings of the submenus

Output

Configuration

Advanced

Configuration

Save Preset

2 3

Erase Preset

1 2 3

Memory

Presets

Quick Start — DDS 402, cont’d

QS-4

Advanced Configuration menu

To reset the scaler, press

and hold the Freeze button

until the reset message

displays.

*Adjust knobs do not affect

this submenu

RGB delay time (in seconds)

• 0.0 to 5.0 seconds in 0.1 sec.

increments (0.7 second default)

Set top and bottom blanking

• 0 to 237, top and bottom

(Adjust for top,

Adjust for bottom)

Smooth edges

• On (default)

• Off

Set test pattern type

• Off (default)

• Color Bars

• Crosshatch

• 4 x 4 crosshatch

• Grayscale

• Crop

• Alt Pix

• Film aspect 1.78

• Film aspect 1.85

• Film aspect 2.35

• Ramp

Display blue and sync only

• On

• Off (default)

Use either Adjust

knob to adjust the

submenus

Output

Configuration

Top Blanking Bot

000 000

Press and Hold

FREEZE to Reset

RGB Delay

0.7 Seconds

Advanced

Configuration

Exit

Test Pattern

Off

Edge Smoothing

OFF

Blue Mode

OFF

Exit menu

MENU MENU

Display

Cycle

Advanced

Configuration

Input

Configuration

Exit

Picture Adjustments menu

10 sec.

timeout

NOTE The Adjust knob and the Adjust knob are

used to adjust the image settings on the left and

right sides of the LCD screen, respectively.

2 sec.

Display

Cycle

Power

CENTER SIZE BRT/CONT ZOOM

DETAIL

Extron 60-426-01

DDS 402

Horz Filter Vert

001 000

Horz Cntr Vert

Horz Size Vert ZoomBrt Cont

001 000

Version

Executive Mode menu

10 sec.

timeout

Press both buttons

simultaneously for

2 seconds

Display

Cycle

CENTER ZOOM

Executive Mode

Enabled

Executive Mode

Disabled

Digital Display Scaler • Table of Contents

Table of Contents

Chapter 1 • Introduction .......................................................................................................1-1

About this Manual .............................................................................................................1-2

About the Scaler..................................................................................................................1-2

Features ...................................................................................................................................1-3

Chapter 2 • Installation..........................................................................................................2-1

Installation Overview .......................................................................................................2-2

Mounting the Scaler..........................................................................................................2-2

Table use.............................................................................................................................2-2

Rack mounting...................................................................................................................2-2

Cabling and Rear Panel Views......................................................................................2-2

Video input connections ...................................................................................................2-3

Video output connections .................................................................................................2-3

RS-232 connection .............................................................................................................2-4

Contact closure connection...............................................................................................2-4

Power connection ..............................................................................................................2-4

Configuration .......................................................................................................................2-4

Chapter 3 • Operation .............................................................................................................3-1

Front Panel Controls and Indicators .........................................................................3-2

Freeze button.....................................................................................................................3-2

Input buttons .....................................................................................................................3-2

Selecting an input ........................................................................................................ 3-2

Recalling presets........................................................................................................... 3-2

Picture adjustment buttons...............................................................................................3-3

LCD display .........................................................................................................................3-3

Menu control buttons .......................................................................................................3-3

Adjustment knobs..............................................................................................................3-3

Button icons .......................................................................................................................3-4

Front Panel Operations....................................................................................................3-4

Power ................................................................................................................................. 3-4

Menu system overview ......................................................................................................3-4

Configuration.....................................................................................................................3-5

Input Configuration menu ...........................................................................................3-5

Input #2 submenu ...............................................................................................3-6

Pixel Phase submenu...........................................................................................3-6

Output Configuration menu ........................................................................................3-6

Resolution and refresh rates submenu ............................................................... 3-7

Output signal submenu ...................................................................................... 3-7

Sync Polarity submenu

........................................................................................ 3-7

Memory Presets menu ..................................................................................................3-8

Save Presets submenu .........................................................................................3-8

Erase Presets submenu ........................................................................................3-8

ii Digital Display Scaler • Table of Contents

Table of Contents, cont’d

Advanced Configuration menu ....................................................................................3-9

Edge Smoothing submenu..................................................................................3-9

Blue Mode submenu ...........................................................................................3-9

Test Pattern submenu .........................................................................................3-9

Blanking submenu ..............................................................................................3-9

RGB Delay submenu............................................................................................3-9

Reset submenu..................................................................................................3-10

Exit menu ...................................................................................................................3-10

Picture adjustments ......................................................................................................... 3-10

Front panel security lockout (executive mode)..............................................................3-11

Optimizing the Video......................................................................................................3-12

Setting up a DVD source .................................................................................................3-12

Chapter 4 • Programmer’s Guide.....................................................................................4-1

Symbols ................................................................................................................................... 4-2

Scaler-Initiated Messages ...............................................................................................4-3

Any time .............................................................................................................................4-3

Power up ............................................................................................................................4-3

Input selection ...................................................................................................................4-3

Input and output video type.............................................................................................4-3

Freeze .................................................................................................................................4-3

Picture adjustments ...........................................................................................................4-3

RGB delay ...........................................................................................................................4-4

Test pattern ........................................................................................................................4-4

Presets ................................................................................................................................4-4

Host-to-Scaler Instructions.............................................................................................4-5

Scaler Error Responses.....................................................................................................4-5

Using the Command/Response Table ........................................................................4-5

Command/response table for SIS commands ...................................................................4-6

Command/response table for special function SIS commands ........................................4-9

Chapter 5 • Scaler Software................................................................................................5-1

Control Software for Windows....................................................................................5-2

Installing the software ......................................................................................................5-2

Using the control program................................................................................................5-2

Using the help program ....................................................................................................5-3

Button-Label Generator...................................................................................................5-4

Installing the software ......................................................................................................5-4

Using the software ............................................................................................................ 5-4

iiiDigital Display Scaler • Table of Contents

Appendix A • Reference Information.......................................................................... A-1

Specifications....................................................................................................................... A-2

Part Numbers ....................................................................................................................... A-3

Included parts ................................................................................................................... A-3

Suggested part.................................................................................................................. A-3

Firmware Upgrade Installation................................................................................... A-4

Button Labels....................................................................................................................... A-6

Installing labels in the scaler’s buttons ............................................................................ A-6

iv Digital Display Scaler • Table of Contents

Table of Contents, cont’d

68-555-01 Rev. D

01 05

All trademarks mentioned in this manual are the properties of their respective owners.

Digital Display Scaler

Chapter One

Introduction

About this Manual

About the Scaler

Features

Introduction, cont’d

Digital Display Scaler • Introduction1-2

Introduction

About this Manual

This manual contains installation, configuration, and operating information for the

Extron DDS 402 digital display scaler.

This chapter identifies the scaler’s features. Chapter 2 details how to install the

scaler. Chapter 3 describes how to operate the scaler and use all of its features.

Chapter 4 provides information about programming the scaler under RS-232

control, such as from a PC or a host controller. Chapter 5 details the Extron control

software for Windows, which allows you to operate the scaler from a PC in a

graphical environment. Appendix A lists the scaler’s specifications and pertinent

part numbers and provides procedures for performing updates and repairs.

About the Scaler

The DDS 402 is a two-input digital display scaler (figure 1-1). The scaler inputs

high-resolution RGBHV/RGBS/RGsB video on a 15HD connector (Input 1) and

either RGBHV/RGBS/RGsB video or component video signals on five BNC

connectors (Input 2). Input 1 is buffered, looped through, and output on a 15HD

connector for use by a local monitor. The DDS 402 scales the selected input up or

down to any 1 of 41 output resolutions and rates and outputs the video as both

RGBHV or RGBS video and HD component video, on five BNCs and a 15HD

connector. Several of the output resolutions and rates include Extron’s Accu-RATE

Frame Lock™ (AFL™), a proprietary technology that locks the output frame rate to

the input rate, solving the problems that result from different input and output

rates. For home theaters, the DDS 402 features HDTV 720p, 1080p, and 1080i

outputs.

Extron

DDS 402

100-24

50-60H

HD Camera

PC Computer

RS-232

Control

Projector

Plasma

Display

Figure 1-1 — DDS 402 digital display scaler

For upscaling, the DDS 402 converts the horizontal and vertical sync timing and

the number of lines of the lower-resolution RGB input to match the native

resolution of the display. This produces an undistorted, brighter picture.

For downscaling, the DDS 402 accepts any computer resolution, up to 1600 x 1200,

with horizontal scan rates up to 100 kHz and vertical scan rates up to 120 Hz, and

converts the input to match the native resolution of the display.

The scaler is ideal for displaying images on projectors with limited display

resolutions, such as liquid-crystal display (LCD) projectors, digital light processor

(DLP) projectors, and plasma projectors.

1-3Digital Display Scaler • Introduction

The scaler also features a zoom function, up to 200%, that maintains the original

aspect ratio. The zoom function makes the scaler ideal for video wall applications

using four displays and four DDS 402s zoomed to 200%.

The scaler features four levels of horizontal filters, which help prevent detail loss,

and ten levels of vertical filtering, which reduce flicker.

Other picture controls that the DDS 402 provides are centering, size, brightness,

and contrast adjustments. The scaler also has a top and bottom line blanking

function.

The DDS 402 is housed in a rack-mountable, 1U high, 17.5" wide metal enclosure.

With the included mounting brackets, the scaler can be rack mounted, or mounted

under a desk or table, or against a wall or the side of a desk. The DDS 402 has an

internal 100VAC to 240VAC, 50/60 Hz, 30 watts auto-switchable power supply that

provides worldwide power compatibility.

Features

Inputs — The DDS 402 switches between two inputs: Input 1 accepts computer

video on a 15HD connector, Input 2 accepts high resolution RGBHV, RGBS,

RGsB, or component video on five BNCs.

Computer video loop-through connector — The computer video input, Input 1, is

buffered, looped through, and output for use on a local monitor on a 15HD

connector.

Outputs — The DDS 402 scales images to the following output resolutions:

• 640 x 480 (VGA) at 50 Hz, 60 Hz, 75 Hz, and lock*

• 800 x 600 (SVGA) at 50 Hz, 60 Hz, 75 Hz, and lock*

• 832 x 624 (Macintosh) at 60 Hz and 75 Hz, and lock*

• 848 x 480 (plasma) at 60 Hz and lock*

• 852 x 480 (plasma) at 60 Hz and lock*

• 1024 x 768 (XGA) at 50 Hz, 60 Hz, 75 Hz, 85 Hz, and lock*

• 1280 x 768 (plasma) at 56 Hz and lock*

• 1280 x 1024 (SXGA) at 50 Hz, 60 Hz, and lock*

• 1360 x 765 (plasma) at 60 Hz and lock*

• 1365 x 1024 (plasma) at 60 Hz and lock*

• 1400 x 1050 (SXGA+) at 50 Hz, 60 Hz, and lock*

• 576p (HDTV) at 50 Hz and lock*

• 720p (HDTV) at 60 Hz and lock*

• 1080p (HDTV) at 60 Hz and lock*

• 1080i (HDTV) at 50 Hz, 60 Hz, and lock*

* See Accu-RATE Frame Lock (patent pending) below.

Introduction, cont’d

Digital Display Scaler • Introduction1-4

Operational flexibility — Operations such as input and scaling selection, picture

controls, and saving and recalling of presets can be performed on the front

panel or over the RS-232 link. The RS-232 link allows remote control via a PC

or control system. Input selection is also available under contact closure

control.

• Front panel control — The scaler front panel controller supports individual

input selection. The front panel features large, positive touch, illuminated

buttons that can be labeled with text or graphics, two rotary knobs for

making adjustments or selecting menu options, and an LCD.

• Windows-based control program — Extron’s Windows-based control

program provides a versatile range of operational options with its graphical

interface and drag-and-drop/point-and-click operation.

• Simple Instruction Set (SIS™) control — The remote control protocol uses

Extron’s SIS for easy programming and operation.

• Contact closure control — The operator can select either input via contact

closure through the Remote port.

Accu-RATE Frame Lock™ (AFL™) — A technology exclusive to Extron that solves

frame rate conversion issues experienced by video scalers. When video input

and output refresh rates differ, occasionally the two rates cross over each

other. The result is a glitch or image freeze on the display. AFL solves this

problem by locking the output frame rate to the input frame rate.

3:2 pulldown detection for NTSC video sources — This advanced, patent pending,

film mode processing feature helps maximize image detail and sharpness for

video sources that originated from film. When film is converted to NTSC

video, the film frame rate has to be matched to the video frame rate in a

process called 3:2 pulldown. Jaggies and other image artifacts can result if

conventional deinterlacing techniques are used on film-source video. The

DDS 402’s advanced film mode processing recognizes signals that originated

from film. The DDS 402 then applies video processing algorithms that

optimize the conversion of video that was made with the 3:2 pulldown

process. This results in richly detailed images with sharply defined lines.

Test patterns — The switcher features built-in test patterns to aid in monitor or

projector set-up and evaluation.

Blue mode — The switcher can be set to output the blue video signal only, to help

installers calibrate the monitor or projector.

Triple-Action Switching™ (RGB delay) — RGB delay blanks the screen when the

scaler switches between inputs. The new sync signals precede the RGB

signals, so that a noise-filled scramble is not shown during the transition.

The time delay between the RGB and sync signals is user adjustable up to

five seconds on the front panel and under RS-232 control.

Horizontal and vertical detail — The DDS 402 offers four levels of horizontal detail

and eight levels of vertical detail. Horizontal and vertical detail minimize the

loss of picture fidelity.

Picture controls — Horizontal and vertical centering, horizontal and vertical sizing,

brightness, contrast, zoom, and detail controls are available for fine picture

adjustments.

Top and bottom line blanking — Extron’s exclusive variable horizontal blanking

feature allows the operator to add black lines at the top and bottom edges of

the image to mask the top and bottom each image.

1-5Digital Display Scaler • Introduction

Freeze mode — Locks the output display to the selected image. Once an input is

frozen, the input can be removed without losing the output image. This

feature lets the DDS 402 function as a still store.

Auto memories — The two inputs support 32 auto-recall memories each, based on

the incoming frequency. Information on sizing, centering, detail, contrast,

and brightness is saved.

Front panel security lockout — Locks out all front panel functions except the input

selection and centering controls. When the front panel is locked, all functions

are still available via RS-232 commands.

Mounting flexibility — Mounting brackets make the 1U high scaler mountable in

any conventional 19” wide rack, or under or through a desk or other

furniture.

Power — The 100VAC to 240VAC, auto-switchable, internal power supply of the

DDS 402 provides worldwide power compatibility.

Introduction, cont’d

Digital Display Scaler • Introduction1-6

Digital Display Scaler

Chapter Two

Installation

Installation Overview

Mounting the Scaler

Cabling and Rear Panel Views

Configuration

Installation, cont’d

Digital Display Scaler • Installation2-2

Installation

Installation Overview

To install and set up a DDS 402 Digital Display Scaler for operation, perform the

following steps:

Disconnect power from all of the equipment, including the video source(s),

and the devices that will receive the scaled video signal.

Rack mount the scaler, if desired. See Mounting the Scaler in this chapter.

Connect the digital input and loop-through cables. See Video input connections

in this chapter.

Connect the digital output cables. See Video output connections in this chapter.

If desired, connect the RS-232 cable. See RS-232 connection and Contact closure

connection in this chapter.

Connect the AC power cable. See Power connection in this chapter.

Mounting the Scaler

The DDS 402 comes with rubber feet and a set of rack mounting brackets.

Tabletop use

For tabletop use, attach a self-adhesive rubber foot to each corner of the bottom of

the DDS 402 scaler.

Rack mounting

Rack mount the scaler as follows:

1. Attach the rack mount brackets to the scaler with eight #8 machine

screws, provided (figure 2-1).

2. Insert the scaler into the rack, align the holes in the mounting bracket

with those of the rack.

2A MAX

100-240V 50-60Hz

REMOTE

RGB/HD R-Y, B-Y, Y

RGB/R-Y, B-Y, Y

RGB

RGB/R-Y, B-Y, Y

/RY

/B-Y

/RY

/B-Y

Rack-mount

Bracket

Figure 2-1 — Mounting the digital display dcaler

3. Secure the scaler to the rack using the supplied machine screws.

Cabling and Rear Panel Views

All connectors are on the rear panel (figure 2-2).

2-3Digital Display Scaler • Installation

2A MAX

100-240V 50-60Hz

REMOTE

RGB/HD R-Y, B-Y, Y

RGB/R-Y, B-Y, Y

RGB

RGB/R-Y, B-Y, Y

/R-Y

/B-Y

HVS

/R-Y

/B-Y

/HV

7 53 64

Figure 2-2 — DDS 402 rear panel connectors

Video input connections

Input 1 (computer video) input (top) connector — Connect computer or RGB

video to this female 15HD connector.

Input 1 (computer video) loop-through (bottom)

connector — Connect a local monitor to this female 15HD

connector. The scaler buffers the computer video input

and loops it on this connector.

The Digital Display Scaler buffers the computer video input signal before

passing it to the loop-through connector. Beyond that, it does not alter the

loop-through video in any way. The loop through output is the same

resolution and frequency as the computer video input.

Input 2 (RGB or component video) connectors — Connect RGBHV, RGBS,

RGsB, or component video (R-Y, Y, B-Y for YUVi or YUVp, or Betacam) to

these female BNC connectors (figure 2-3).

Ensure that the correct Input 2 video format is selected from the front panel

menu, see Input #2 submenu, in chapter 3, Operation, or via the RS-232

port, see chapter 4, Programmer’s Guide, and chapter 5, Scaler Software.

/R-Y

/B-Y

/R-Y

/B-Y

/HV

V H

/HV

/R-Y

/B-Y

/HV

RGBHV video

RGBS video

RGsB video Component video (R-Y, B-Y, Y)

/R-Y

/B-Y

/HV

Figure 2-3 — Input 2 connections for RGBHV, RGBS, RGsB and

component video

For RGBHV video — Connect to five BNC connectors.

For RGBS video — Connect to four BNC connectors.

For RGsB and component video — Connect to three BNC connectors.

Video output connections

The two video output connectors, the 15HD connector and the five BNC

connectors, both output the same video signal. The 15HD connector outputs

RGBHV only, not RGBS.

RGB/HD R-Y, B-Y, Y Output 15HD connector — Connect an RGB video or

HD component video display to this female 15HD connector.

RGB

Installation, cont’d

Digital Display Scaler • Installation2-4

RGB/HD R-Y, B-Y, Y Output BNC connectors — Connect an RGB video or

HD component video display to these female BNC connectors (figure 2-4).

RGBHV video

RGBS video

Component video (R-Y, B-Y, Y)

/R-Y

/B-Y

/R-Y

/B-Y

/R-Y

/B-Y

Figure 2-4 — BNC output connections for RGBHV, RGBS, and component

video

For RGBHV video — Connect to five BNC connectors.

For RGBS video — Connect to four BNC connectors.

For component video — Connect to three BNC connectors.

RS-232 connection

Remote port — Connect a host device, such as a computer or touch panel

control, to the Digital Display Scaler via this 9-pin D connector for serial

RS-232 control (figure 2-5).

Female

Male

RS-232 FunctionPin

—

Gnd

—

Contact closure, input #1

Transmit data

Receive data

Contact closure, input # 2

Signal ground

Not used

Figure 2-5 — Remote port pin assignments

See chapter 4, Programmer’s Guide, for definitions of the SIS commands and

chapter 5, Scaler Software to install and use the control software.

Contact closure connection

Remote port — The Remote connector also provides a way to select an input

using a remote contact closure device. Contact closure control uses pins on

the Remote connector that are not used by the RS-232 interface (figure 2-5).

To select a different input number using a contact closure device, momentarily

short the pin for the desired input number to logic ground (pin 5). To force

one of the inputs to be always selected, leave the short to logic ground in

place. The short overrides front panel input selections.

Power connection

AC power connector — Plug a standard IEC power cord into this connector

to connect the scaler to a 100 to 240VAC, 50 Hz or 60 Hz power source. The

front panel control and input selection buttons light in sequence during

power-up, the LCD displays the product name and then cycles through the

default messages.

Configuration

DDS 402 can be configured using either the front panel controls, the SIS, or the

Windows Control program. See chapter 3, Operation, chapter 4, Programmer’s Guide,

and chapter 5, Scaler Software for more information.

Page is loading ...

Extron electronic DDS 402 User manual

Brand: Extron electronic

Model: DDS 402

Category: Plasma TVs

Type: User manual

This manual is also suitable for

Extron Electronics Home Theater Screen DDS 402

Download PDF

report

Extron electronic DDS 402 User manual

This manual is also suitable for

Extron electronic DDS 402 User manual

Related papers

Other documents