Radiant iMODULE User manual

Brand: Radiant

Model: iMODULE

Type: User manual

Radiant iMODULE lets you manage your heating system conveniently via your smartphone or tablet, using the iMODULE app. Its intuitive and user-friendly interface provides remote control over your heating system, allowing you to adjust temperatures, set schedules, and monitor energy consumption. With iMODULE, you can create personalized heating profiles that adapt to your daily routine, ensuring maximum comfort and energy efficiency. Whether you're at home or away, you'll have complete control over your heating system at your fingertips.

iMODULE - RAD - ING - Manuale - 1507.1

User's manual

iMODULE

Remote Control via Wi-Fi or GSM

iMODULE - RAD - ING - Manuale - 1507.1

iMODULE_EN

TABLE OF CONTENTS

1. INSTALLER SECTION 3

1.0.1. INSTALLER REGISTRATION 4

1.0.2. REGISTERING A NEW USER 4

1.0.3. HOW TO CONFIGURE THE PARAMETERS OF THE NEW UNIT 5

1.0.4. WIRING 7

1.0.5. CONFIGURATION OF IMODULE GSM VERSION 9

1.0.6. CONFIGURATION OF IMODULE WI-FI VERSION 10

2. USER SECTION 11

2.0.1. APP IMODULE 12

2.0.2. LOCAL-CONTROLLER 13

2.0.3. RECEIVER IMODULE 14

The operations of installation, described in this section,

must be performed by qualified personnel only, who has

technical expertise in the field required to installation and

maintenance of the parts of the heating and DHW production

systems for civil and industrial buildings as provided in Art.

3 of Min. Decree no. 37 dated 22.01.2008.

1. INSTALLER SECTION

iMODULE - RAD - ING - Manuale - 1507.1

1 Installazione_iMODULE_v.1502_EN

2. INSTALLATION

INSTALLER

1.0.1. INSTALLER REGISTRATION

› Open the page ‘http://www.imodule.it/’;

› Click on “Registration Form”;

› Type in the page the following data:

· Installer's Name;

· Installer's Surname;

· Installer's Email Address;

· Choose a password;

· Installer's Address;

· Installer's mobile phone number (with

international dialling code);

· Country;

· VAT number (11 characters);

· Captcha code.

› Press "Send".

› To confirm the registration, the installer must

click on the link received by email;

› after confirmation, the installer receives a second

email with a summary of login credentials and an

attachment with the instructions for accessing

the technical panel of the iModule APP.

1.0.2. REGISTERING A NEW USER

› Open the page ‘http://app.imodule.it/admin’;

› Enter the installer login credentials and click on

"Login".

› The list of registered users (if any) will be

displayed.

› To add a new User click on “New User/Boiler”.

› Enter the information regarding the new iModule

unit to register:

· UserName and Password (that will be used by

the user to log in to iMODULE APP);

· Name and Surname of system/iModule owner;

· Serial number of the iModule (without the

zeros before the digit, for a serial number

00000168 you will write 168); the serial number

is specified in the iModule unit, on the label

above connector 'A' and below connector 'C'

(see fig. 3 in chapter 'WIRING' );

· the phone number of the SIM card inserted in

the iModule (only for iModule in GSM version);

· the place (province) of the iModule unit.

› Once you have entered the data, click on “Save”.

› Return to the home page, in the list of users,

where is displayed the new iModule registered.

INSTALLATION

iMODULE - RAD - ING - Manuale - 1507.1

1 Installazione_iMODULE_v.1502_EN

2. INSTALLATION

INSTALLER

1.0.3. HOW TO CONFIGURE THE PARAMETERS OF THE NEW UNIT

To configure the parameters of the new unit click on the adjustable spanner icon (see fig. 1).

fig. 1

fig. 2

iMODULE - RAD - ING - Manuale - 1507.1

1 Installazione_iMODULE_v.1502_EN

2. INSTALLATION

INSTALLER

OPEN-THERM PROTOCOL CONFIGURATION

Use the parameter “OT Protocol version” (see fig.2)

to configure the iModule based on the version of

the Open-Therm Protocol used by the boiler:

› 0 = for boilers with electronic printed circuit

board NORDGAS;

› 1 = for boilers with electronic printed circuit

board HONEYWELL;

› 2 = non applicable.

CONFIGURATION OF STANDARD/DST TIME

You can switch from standard time to daylight

saving time (and vice versa), using the parameter

"DST change" (see figure 2) and modify the time of

the iModule by one hour, according to the following

convention:

› 0 = no change to current iModule time;

› 1 = add one hour to current iModule time;

› 255 = remove one hour from current iModule

time.

TIME ZONE CONFIGURATION

You can manage all of the time zones from -12

hours to +14 hours, in relation to UTC coordinated

universal time, with a resolution of half an hour.

The time zone of the iModule is set using the

parameter "Time Zone" (see fig.2), within its his

range [104÷156], according to the following rule:

· value of parameter “Time Zone” = 128 +

difference of iModule time in relation to UTC

time, multiplied by 2.

Examples of Time Zones:

UTC Time (Time Zone 0) = set “Time Zone” = 128;

Western Europe Time (Time one 1) = set "Time

Zone" = 130;

India Time (Time Zone +5.5) = set “Time Zone” =

139;

Examples by City:

Paris/Rome = UTC Time + 1 = set “Time Zone” =

130;

London = UTC Time = set “Time Zone” = 128;

Moscow = UTC Time + 3 = set “Time Zone” = 134;

Kiev = UTC Time +2 = set “Time Zone” = 132;

Tehran = UTC Time +3.5 = set “Time Zone” = 135.

OPEN-THERM (OT) CONFIGURATION OR ROOM

THERMOSTAT (RT)

For iModule systems connected to Open-Therm

boilers (configuration–OT), set the parameter

“Connection Type (OT/RT)” = 0;

For iModule systems connected to Room

Thermostat boilers (configuration–RT), set the

parameter “Connection Type (OT/RT)” = 1;

iMODULE - RAD - ING - Manuale - 1507.1

1 Installazione_iMODULE_v.1502_EN

2. INSTALLATION

INSTALLER

1.0.4. WIRING

Install the Local-Controller within the home, for

example in the same position as the previous

programmable thermostat/remote controller.

Install the iModule in any place inside the house

(house, cellar, boiler room, under the stairs… ), with

a good GSM signal (for iModule in GSM version)

or in the vicinity of the WI-FI Router/Switch (for

iModule in Wi-Fi version);

Once you have installed the Local-Controller and

the iModule, carry out the following electrical

connections (see fig.3):

· Open-Therm connection between iModule

and Local-Controller (2 wires);

· Connection between the iModule and the

Boiler (2 wires) via Open-Therm or Room

Thermostat Relay;

· iModule connection to the power supply

network (230VAC).

KEY

Connector A (Power supply):

· N - Neutral point of power cord (mains voltage

230 VAC, 50 Hz);

· L - Phase of power cord (mains voltage 230

VAC, 50 Hz);

· G - Grounding point of power cord (mains

voltage 230 VAC, 50 Hz);

Connector B (for Room Thermostat versions only):

· T1 and T2 should be connected to the boiler

to activate the heating request via the Room

Thermostat relay.

Connector C (Open-Therm connections):

· B1 and B2 should be connected to Open-

Therm bus of the boiler (only for boilers with

Open-Therm configuration);

· R1 and R2 should be connected to the Local

Controller.

fig. 3

iMODULE - RAD - ING - Manuale - 1507.1

1 Installazione_iMODULE_v.1502_EN

2. INSTALLATION

INSTALLER

WIRING DIAGRAM OF OPENTHERM BOILER

WIRING DIAGRAM OF ROOM THERMOSTAT BOILER

fig. 4

fig. 5

iMODULE - RAD - ING - Manuale - 1507.1

1 Installazione_iMODULE_v.1502_EN

2. INSTALLATION

INSTALLER

1.0.5. CONFIGURATION OF IMODULE GSM VERSION

WARNING

Use only SIM card “2G” type “DATA” or “OPTION + DATA” (the SIM cards “3G” are not supported like

in the case of telephone provider TRE).

To insert the SIM card into the iModule see fig.6.

Send an SMS to the telephone number associated to the SIM card inserted in the iModule with the following

format:

APN:xxx# (instead of ‘xxx’ insert the APN of the operator of the SIM card inserted in the iModule).

Below are some examples of APN for Italian operators:

TIM = ibox.tim.it

VODAFONE = mobile.vodafone.it

WIND = internet.wind

Example of SMS to send to the iModule:

APN:internet.wind#

fig. 6

iMODULE - RAD - ING - Manuale - 1507.1

1 Installazione_iMODULE_v.1502_EN

2. INSTALLATION

INSTALLER

1.0.6. CONFIGURATION OF IMODULE

WI-FI VERSION

Power the iModule unit (via connector A, see fig.3 in

chapter ‘WIRING’);

a Wi-Fi network called “iModule_WiFi” will be

activated for 10 minutes; the network can be

accessed without password;

Connect a Wi-Fi device (PC/Laptop/Tablet/

Smartphone) to “iModule_WiFi” network;

Open a Web-Browser in the Wi-Fi device

(recommended Browsers: Internet Explorer

Mozilla Firefox

, Safari

) and select the web page:

http://captiveportal.net;

If the web page ‘http://captiveportal.net’ does not

open promptly, we suggest you disable the Proxy

server, where applicable (check the connection

options or browser settings);

Enter the data requested in the following fields

(fig.7):

› Insert miniAP PassKey: nordgas

› Insert the SSID: name of Wi-Fi network to which

the iModule will connect

› Insert the PSK: name of Wi-Fi network to which

the iModule will connect

› Ignor the following 4 fields “Insert Static IP

Address”, “Insert Static NetMask”, “Insert Static

GW Address” and “Insert Static DNS Address”

› Turn on/off DNS/DHCP: select “ON”

› Choose Auth Type: select “Open System”

› Choose Auth: select one of the following options

based on the safety protocol of the Wi-Fi network

to which the device will connect:

· “WPA/WPA2” (with password);

· “WEP” (with password);

· “Open” (without password) for free Wi-Fi

networks;

› Choose Mode: select Station;

› Finally, press Press “GO!”.

After a few seconds, the “iModule_WiFi” network

is disabled by the iModule unit via the dedicated

automatic disable function of the Wi-Fi device;

On the APP iModule, wait for max 3/5 minutes and

check that the room temperature displayed was

updated.

NOTE: should it be necessary to repeat the Wi-

Fi setup (for example when you need to change

one or more parameters of the Wi-Fi network to

connect), cut off power to the iModule and repeat

the configuration procedure.

fig. 7

the operations described in this section are addressed to

all those who will use the machine. The machine must be

used and accessed only by qualified operators that fully

read and understood the User section, paying particular

attention to the warnings.

2. USER SECTION

iMODULE - RAD - ING - Manuale - 1507.1

3 APP iMODULE_EN

2. USE

USER

The iModule consists of:

› APP iMODULE installed on Smartphone and

Tablet;

› Local-Controller (with room temperature

sensor);

› Receiver iModule (in GSM or Wi-Fi version).

2.0.1. APP IMODULE

The APP iMODULE allows you to control the boiler

connected to the Receiver iModule via your personal

electronic device (Tablet and Smartphone).

Download the APP iMODULE for iOS (Apple iPhone/

iPad) and Android for free easily, by scanning the

QR (quick response) code below:

Or find the APP “iMODULE” directly in:

· App Store for iOS (Apple iPhone/iPad)

· Google Play for Android.

Once you have installed the APP iMODULE you can

access the DEMO version (username and password

not required), to test the interface and the control

logic of the system without being connected to any

real system.

Installer of you unit.

In he login page, you can select the application

language from the following:

· English

· Italian

· Czech

· Polish

· Russian

· Ukrainian

You can also use the APP iMODULE from the

browser entering the access credentials in the

web page ‘http://app.imodule.it/home’. For quick

access, scan the QR (quick response) code below:

USE

iMODULE - RAD - ING - Manuale - 1507.1

3 Local-Controller_EN

2. USE

USER

2.0.2. LOCAL-CONTROLLER

The Local–Controller unit is equipped with a sensor

that measures the room temperature displayed on

the APP iMODULE.

The Local–Controller allows the User to set, in

MANUAL mode, the desired room temperature

using the adjustment dial.

KEY OF USER INTERFACE (SEE FIG.1)

1. Dial: used to set the room temperature within

the range from 10°C to 30°C, valid fro MANUAL

mode only;

2. Green LED:

· Steadily Lit: MANUAL mode enabled (boiler

controlled by the Local-Controller).

· Flashing Slowly: AUTOMATIC mode enabled

(boiler controlled by the APP iMODULE).

· Flashing Quickly: MANUAL mode enabled

(power has been cut off to Receiver iModul,

the boiler is controlled directly by the Local-

Controller);

3. Push button: hold it down for three seconds

to switch from AUTOMATIC to MANUAL mode

and vice versa;

4. Red LED:

· Steadily Lit: failed communication between

Open-Therm amd Receiver iModule or boiler;

· LED off: no failure;

· Flashing Slowly: Room sensor failure (on

Local-Controller);

· Flashing Quckly: Receiver iModule failure (no

communication to APP iModule).

USE

fig. 1

iMODULE - RAD - ING - Manuale - 1507.1

3 iModule Ricevitore_EN

2. USE

USER

2.0.3. RECEIVER IMODULE

The Receiver iModule enables, in AUTOMATIC

mode, exchanging data between the boiler and your

personal electronic device (Tablet and Smartphone)

controlled by the APP iMODULE.

KEY OF LED USER INTERFACE ‘1’ (FIG.1)

› Green LED Steadily Lit: AUTOMATIC mode

enabled (boiler controlled by the APP iMODULE).

› Alternating Red and Green Flashing LED: the

system is not configured (for WI-FI version,

configure the WI-FI network to connect; for GSM

version send an SMS to configure the APN).

› Green Slow Flashing LED (1 flash every 2.5

seconds): MANUAL mode enabled, boiler

controlled by Local-Controller.

› Green Slow Flashing LED (1 flash every second):

GSM/Wi-Fi communication in progress.

› Green Quick Flashing LED (5 flashes every

second): Wi-Fi communication (mini access-

point) in progress.

› Red Steadily Lit LED: GSM/Wi-Fi communication

failure.

› Red Slow Flashing LED (1 flash every second):

Local-Controller communication failure.

› Red Quick Flashing LED (5 flash every second):

boiler communication failure (if configured as

Open-Therm).

› LED off: iModule not powered.

If power has been cut off to Receiver iModul, the

boiler is controlled directly by the Local-Controller

in MANUAL mode.

USE

fig. 1

RADIANT BRUCIATORI S.p.A.

Via Pantanelli, 164/166 - 61025 - Montelabbate (PU)

Tel. +39 0721 9079.1 • fax. +39 0721 9079279

e-mail: info@radiant • http://www.radiant.it

Radiant iMODULE User manual

Radiant iMODULE User manual

Radiant iMODULE User manual

Related papers

Other documents