Danfoss VLT HVAC Drive FC 102 Operating instructions

Contents

1 Safety

1-1

Safety instructions 1-1

Before Commencing Repair Work 1-2

Special conditions 1-2

Avoid unintended Start. 1-3

Safe Stop of the Adjustable Frequency Drive 1-3

IT Line Power 1-5

2 Introduction

2-1

3 Mechanical installation

3-1

Before starting 3-1

Mechanical Dimensions 3-3

4 Electrical installation

4-1

How to connect 4-1

Line power wiring overview 4-6

Motor wiring overview 4-13

DC bus connection 4-17

Brake Connection Option 4-18

Relay Connection 4-20

How to Test Motor and Direction of Rotation. 4-24

Electrical Installation and Control Cables 4-27

5 How to operate the adjustable frequency drive

5-1

Three ways of operating 5-1

How to operate the numeric LCP (NLCP) 5-1

Tips and tricks 5-5

6 How to program the adjustable frequency drive

6-1

How to program 6-1

Quick Menu Mode 6-1

Function Set-ups 6-10

Parameter list 6-55

Main Menu Structure 6-55

0-** Operation and Display 6-56

1-** Load / Motor 6-58

2-** Brakes 6-59

VLT

®

HVAC Drive Instruction Manual Contents

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

3-** Reference / Ramps 6-60

4-** Limits / Warnings 6-61

5-** Digital In / Out 6-62

6-** Analog In / Out 6-64

8-** Communication and Options 6-66

9-** Profibus 6-67

10-** CAN Fieldbus 6-68

11-** LonWorks 6-69

13-** Smart Logic Controller 6-70

14-** Special Functions 6-71

15-** FC Information 6-72

16-** Data Readouts 6-74

18-** Info & Readouts 6-76

20-** FC Closed-loop 6-77

21-** Ext. Closed-loop 6-78

22-** Application Functions 6-80

23-** Time-based Funtions 6-82

24-** Application Functions 2 6-83

25-** Cascade Controller 6-84

26-** Analog I / O Option MCB 109 6-86

7 Troubleshooting

7-1

Alarms and warnings 7-1

Fault messages 7-4

Acoustic noise or vibration 7-6

8 Specifications

8-1

General Specifications 8-1

Special Conditions

8-20

9 Index

9-1

Contents VLT

®

HVAC Drive Instruction Manual

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

1Safety

1.1.1 Symbols

Symbols used in this manual:

NOTE!

Indicates something to be noted by the reader.

Indicates a general warning.

Indicates a high-voltage warning.

✮ Indicates a default setting

1.1.2 High voltage warning

The voltage of the adjustable frequency drive and the MCO 101 option card is dangerous whenever it is connected to line power.

Incorrect installation of the motor or adjustable frequency drive may cause damage to the equipment, serious injury or death. Con-

sequently, it is essential to comply with the instructions in this manual as well as local and national rules and safety regulations.

1.1.3 Safety instructions

Prior to using functions directly or indirectly influencing personal safety (e.g., Safe Stop, Fire Mode or other functions either forcing

the motor to stop or attempting to keep it functioning), a thorough risk analysis and system test must be carried out. The system

tests must include testing failure modes regarding the control signaling (analog and digital signals and serial communication.

NOTE!

Before using fire mode, contact Danfoss

VLT

®

HVAC Drive Instruction Manual 1 Safety

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

1-1

1

• Make sure the adjustable frequency drive is properly grounded.

• Do not remove AC line input connections, motor connections or other power connections while the adjustable frequency drive is connected to

line power.

• Protect users against supply voltage.

• Protect the motor against overloading in accordance with national and local regulations.

• The ground leakage current exceeds 3.5 mA.

• The [OFF] key is not a safety switch. It does not disconnect the adjustable frequency drive from line power.

1.1.4 Before Commencing Repair Work

1. Disconnect the adjustable frequency drive from line power.

2. Disconnect DC bus terminals 88 and 89.

3. Wait at least the time mentioned above in the section General Warning.

4. Remove motor cable

1.1.5 Special conditions

Electrical ratings:

The rating indicated on the nameplate of the adjustable frequency drive is based on a typical 3-phase line power supply within the specified voltage,

current and temperature ranges, which are expected to be used in most applications.

The adjustable frequency drives also support other special applications, which affect the electrical ratings of the adjustable frequency drive.

Special conditions that affect the electrical ratings might be:

• Single phase applications.

• High temperature applications that require derating of the electrical ratings.

• Marine applications with more severe environmental conditions.

Other applications might also affect the electrical ratings.

Consult the relevant sections in this manual and in the

VLT HVAC Drive Design Guide, MG.11.BX.YY

for information about the electrical ratings.

Installation requirements:

The overall electrical safety of the adjustable frequency drive requires special installation considerations regarding:

• Fuses and circuit breakers for overcurrent and short-circuit protection

• Selection of power cables (line power, motor, brake, load sharing and relay)

• Grid configuration (IT,TN, grounded leg, etc.)

• Safety of low-voltage ports (PELV conditions).

Consult the relevant clauses in these instructions and in the

VLT HVAC Drive Design Guide

for information about the installation requirements.

1 Safety VLT

®

HVAC Drive Instruction Manual

1-2

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

1

1.1.6 Caution

Caution

The adjustable frequency drive DC link capacitors remain charged after power has been disconnected. To avoid an electrical shock hazard, disconnect

the adjustable frequency drive from line power before carrying out maintenance. Wait at least as follows before doing service on the adjustable

frequency drive:

Voltage

Minimum Waiting Time

4 min. 15 min. 20 min. 30 min. 40 min.

200–240 V 1.1 - 3.7 kW 7.5–60 hp [5.5–45 kW]

380–480 V 1.1 - 7.5 kW 15–125 hp [11–90 kW]

150–300 hp [110–200

kW]

350–600 hp [250–450

kW]

525–600 V

1.5–10 hp [1.1–7.5

kW]

150–350 hp [110–250

kW]

450–750 hp [315–560

kW]

525–690 V 60–125 hp [45–90 kW]

150–350 hp [110– 250

kW]

450–750 hp [315– 560

kW]

850–1600 hp [630–

1200 kW]

Be aware that there may be high voltage on the DC link even when the LEDs are turned off.

1.1.7 Installation at high altitudes (PELV)

At altitudes above 6,600 feet [2 km], please contact Danfoss regarding PELV.

1.1.8 Avoid unintended Start.

While the adjustable frequency drive is connected to line power, the motor can be started/stopped using digital commands, bus

commands, references or via the Local Control Panel.

• Disconnect the adjustable frequency drive from line power whenever personal safety considerations make it necessary to avoid an unintended

start.

• To avoid an unintended start, always activate the [OFF] key before changing parameters.

• Unless terminal 37 is turned off, an electronic fault, temporary overload, a fault in the line power supply or lost motor connection may cause a

stopped motor to start.

1.1.9 Safe Stop of the Adjustable Frequency Drive

For versions equipped with a Safe Stop terminal 37 input, the adjustable frequency drive can perform the safety function

Safe Torque Off

(as defined by

draft CD IEC 61800-5-2) or

Stop Category 0

(as defined in EN 60204-1).

It is designed and deemed suitable for the requirements of Safety Category 3 in EN 954-1. This functionality is called Safe Stop. Prior to integrating and

using safe stop in an installation, a thorough risk analysis must be carried out on the installation in order to determine whether the safe stop functionality

and safety category are appropriate and sufficient. In order to install and use the safe stop function in accordance with the requirements of Safety Category

3 in EN 954-1, the related information and instructions of the

VLT HVAC Drive Design Guide

must be followed! The information and instructions contained

in the Instruction Manual are not sufficient for a correct and safe use of the safe stop functionality!

VLT

®

HVAC Drive Instruction Manual 1 Safety

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

1-3

1

130BA491

This certificate also covers FC 102 and FC 202!

1 Safety VLT

®

HVAC Drive Instruction Manual

1-4

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

1

1.1.10 IT Line Power

IT Line Power

Do not connect 400 V adjustable frequency drives with RFI filters to line supplies with a voltage between phase and ground of more

than 440 V.

For IT line power and delta ground (grounded leg), AC line voltage may exceed 440 V between phase and ground.

par. 14-50

RFI 1

can be used to disconnect the internal RFI capacitors from the RFI filter to ground. If this is done, it will reduce the RFI performance

to A2 level.

1.1.11 Software version and approvals: VLT HVAC Drive

VLT HVAC Drive

Software version: 3.1.x

This manual can be used with all VLT HVAC Drive adjustable frequency drives with software version 3.1.x.

The software version number can be seen from par. 15-43

Software Version

.

1.1.12 Disposal Instructions

Equipment containing electrical components must not be disposed of together with domestic waste.

It must be separately collected with electrical and electronic waste according to local and currently valid leg-

islation.

VLT

®

HVAC Drive Instruction Manual 1 Safety

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

1-5

1

1 Safety VLT

®

HVAC Drive Instruction Manual

1-6

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

1

2Introduction

2.1 Introduction

2.1.1 Available literature

- Instruction Manual MG.11.Ax.yy provides the necessary information for getting the adjustable frequency drive up and running.

- Design Guide MG.11.Bx.yy contains all the technical information about the adjustable frequency drive and customer design and applications.

- Programming Guide MG.11.Cx.yy provides information on how to program and includes complete parameter descriptions.

- Mounting Instruction, Analog I/O Option MCB109, MI.38.Bx.yy

-

PC-based Configuration Tool MCT 10, MG.10.Ax.yy enables the user to configure the adjustable frequency drive from a Windows

™

based PC

environment.

-

Danfoss VLT

®

Energy Box software at

www.danfoss.com/BusinessAreas/DrivesSolutions

, then choose PC Software Download

-

VLT

®

VLT HVAC Drive Drive Applications, MG.11.Tx.yy

- Instruction Manual VLT HVAC Drive BACnet, MG.11.Dx.yy

- Instruction ManualVLT HVAC Drive Profibus, MG.33.Cx.yy.

- Instruction ManualVLT HVAC Drive Device Net, MG.33.Dx.yy

- Instruction ManualVLT HVAC Drive LonWorks, MG.11.Ex.yy

- Instruction Manual VLT HVAC Drive High Power, MG.11.Fx.yy

- Instruction ManualVLT HVAC Drive Metasys, MG.11.Gx.yy

- Instruction Manual VLT HVAC Drive FLN, MG.11.Zx.yy

x = Revision number

yy = Language code

Danfoss technical literature is available in print from your local Danfoss Sales Office or online at:

www.danfoss.com/BusinessAreas/DrivesSolutions/Documentations/Technical+Documentation.htm

VLT

®

HVAC Drive Instruction Manual 2 Introduction

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

2-1

2

2.1.2 Adjustable Frequency Drive Identification

Below is an example of an identification label. This label is situated on the adjustable frequency drive and shows the type and the options with which the

unit is equipped. See below for details of how to read the Type code string (T/C).

Figure 2.1: This example shows an identification label.

NOTE!

Please have T/C (type code) number and serial number ready before contacting Danfoss.

2 Introduction VLT

®

HVAC Drive Instruction Manual

2-2

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

2

2.1.3 Type Code String

Description Pos Possible choice

Product group & FC Series 1-6 FC 102

Power rating 8-10 1.1–560 kW (P1K1 - P560)

Number of phases 11 Three phases (T)

AC line voltage 11-12

T 2: 200–240 V AC

T 4: 380–480 V AC

T 6: 525–600 V AC

Enclosure 13-15

E20: IP20

E21: IP 21/NEMA Type 1

E55: IP 55/NEMA Type 12

E2M: IP21/NEMA Type 1 w/ line power shield

E5M: IP 55/NEMA Type 12 w/ line power shield

E66: IP66

P21: IP21/NEMA Type 1 w/ backplate

P55: IP55/NEMA Type 12 w/ backplate

RFI filter 16-17

H1: RFI filter class A1/B

H2: RFI filter class A2

H3: RFI filter class A1/B (reduced cable length)

H4: RFI filter class A2/A1

Brake 18

X: No brake chopper included

B: Brake chopper included

T: Safe Stop

U: Safe + brake

Display 19

G: Graphical Local Control Panel (GLCP)

N: Numeric Local Control Panel (NLCP)

X: No Local Control Panel

Coating PCB 20

X. No coated PCB

C: Coated PCB

Line power option 21

X: No line power disconnect switch

1: With line power disconnect switch (IP55 only).

See Chapter 8 for max. cable sizes.

Adaptation 22 Reserved

Adaptation 23 Reserved

Software release 24-27 Current software

Software language 28

A options 29-30

AX: No options

A0: MCA 101 Profibus DP V1

A4: MCA 104 DeviceNet

AG: MCA 108 Lonworks

AJ: MCA 109 BACnet gateway

B options 31-32

BX: No option

BK: MCB 101 General purpose I/O option

BP: MCB 105 Relay option

BO: MCB 109 Analog I/O option

C0 options MCO 33-34 CX: No options

C1 options 35 X: No options

C option software 36-37 XX: Standard software

D options 38-39

DX: No option

D0: DC backup

Table 2.1: Type code description.

The various options and accessories are described further in the

VLT HVAC Drive Design Guide, MG.11.BX.YY

.

VLT

®

HVAC Drive Instruction Manual 2 Introduction

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

2-3

2

2.1.4 Abbreviations and Standards

Abbreviations: Terms: SI units: I-P units:

a Acceleration

m/s

2

ft/s

2

AWG American wire gauge

Auto Tune Automatic Motor Tuning

°C

Celsius

I Current A Amp

I

LIM

Current limit

Joule Energy J = N∙m ft-lb, Btu

°F

Fahrenheit

FC Adjustable Frequency Drive

f Frequency Hz Hz

kHz Kilohertz kHz kHz

LCP Local Control Panel

mA Milliampere

ms Millisecond

min Minute

MCT Motion Control Tool

M-TYPE Motor Type Dependent

Nm Newton meters in-lbs

I

M,N

Nominal motor current

f

M,N

Nominal motor frequency

P

M,N

Nominal motor power

U

M,N

Nominal motor voltage

par. Parameter

PELV Protective Extra Low Voltage

Watt Power W Btu/hr, hp

Pascal Pressure Pa = N/m² psi, psf, ft of water

I

INV

Rated Inverter Output Current

RPM Revolutions Per Minute

SR Size Related

T Temperature C F

t Time s s, hr

T

LIM

Torque limit

U Voltage V V

Table 2.2: Abbreviation and Standards table

2 Introduction VLT

®

HVAC Drive Instruction Manual

2-4

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

2

3 Mechanical installation

3.1 Before starting

3.1.1 Checklist

When unpacking the adjustable frequency drive, make sure that the unit is undamaged and complete. Use the following table to identify the packaging:

Enclosure

type:

A2

(IP 20-21)

A3

(IP 20-21)

A5

(IP 55-66)

B1/B3

(IP 20-21-55-66)

B2/B4

(IP 20-21-55-66)

C1/C3

(IP 20-21-55-66)

C2*/C4

(IP 20-21-55-66)

Unit size (kW):

200–240 V

1.1–3.0 3.7 1.1–3.7

5.5–11/

5.5–11

15/

15–18.5

18.5–30/

22–30

37-45/

37-45

380–480 V 1.1–4.0 5.5–7.5 1.1–7.5

11–18.5/

11–18.5

22-30/

22-37

37-55/

45-55

75-90/

75-90

525–600 V 1.1–7.5

11–18.5/

11–18.5

22-37/

22-37

45-55/

45-55

75-90/

75-90

Table 3.1: Unpacking table

Please note that it is recommended to have a selection of screwdrivers (phillips or cross-thread screwdriver and torx), a side-cutter, drill and knife handy

for unpacking and mounting the adjustable frequency drive. The packaging for these enclosures contains, as shown: accessory bag(s), documentation

and the unit. Depending on options fitted, there may be one or two bags and one or more booklets.

VLT

®

HVAC Drive Instruction Manual 3 Mechanical installation

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

3-1

3

A2 A3 A5 B1 B2 B3 B4 C1 C2 C3 C4

IP20/21 IP20/21 IP55/66 IP21/55/66 IP21/55/66 IP20 IP20 IP21/55/66 IP21/55/66 IP20 IP20

Figure 3.1: Top and bottom mounting holes.

Figure 3.2: Top and bottom mounting holes. (B4+C3+C4 only)

Accessory bags containing necessary brackets, screws and connectors are included with the drives upon delivery.

All measurements in mm.

3.2.1 Mechanical Front Views

3 Mechanical installation VLT

®

HVAC Drive Instruction Manual

3-2

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

3

Mechanical dimensions

Frame size (kW): A2 A3 A5 B1 B2 B3 B4 C1 C2 C3 C4

200–240 V

380–480 V

525–600 V

1.1–3.0

1.1–4.0

-

3.7

5.5–7.5

1.1–7.5

1.1–3.7

1.1–7.5

5.5–11

11–18.5

15

22-30

5.5–11

11–18.5

15–18.5

22–37

18.5–30

37–55

37-45

75-90

22-30

45-55

37-45

75-90

IP

NEMA

20

Chassis

21

Type 1

20

Chassis

21

Type 1

55/66

Type 12

21/ 55/66

Type 1/12

21/ 55/66

Type 1/12

20

Chassis

20

Chassis

21/ 55/66

Type 1/12

21/ 55/66

Type 1/12

20

Chassis

20

Chassis

Height (mm)

Enclosure A** 246 372 246 372 420 480 650 350 460 680 770 490 600

..with de-coupling plate A2 374 - 374 - - - - 419 595 - - 630 800

Backplate A1 268 375 268 375 420 480 650 399 520 680 770 550 660

Distance between mount. holes a 257 350 257 350 402 454 624 380 495 648 739 521 631

Width (mm)

Enclosure B 90 90 130 130 242 242 242 165 231 308 370 308 370

With one C option B 130 130 170 170 242 242 242 205 231 308 370 308 370

Backplate B 90 90 130 130 242 242 242 165 231 308 370 308 370

Distance between mount. holes b 70 70 110 110 215 210 210 140 200 272 334 270 330

Depth (mm)

Without option A/B C 205 205 205 205 200 260 260 248 242 310 335 333 333

With option A/B C* 220 220 220 220 200 260 260 262 242 310 335 333 333

Screw holes (mm)

c 8.0 8.0 8.0 8.0 8.2 12 12 8 - 12 12 - -

Diameter ø d 11 11 11 11 12 19 19 12 - 19 19 - -

Diameter ø e 5.5 5.5 5.5 5.5 6.5 9 9 6.8 8.5 9.0 9.0 8.5 8.5

f 9 9 9 9 9 9 9 7.9 15 9.8 9.8 17 17

Max weight

(kg)

4.9 5.3 6.6 7.0 14 23 27 12 23.5 45 65 35 50

* Depth of enclosure will vary with different options installed.

** The free space requirements are above and below the bare enclosure height measurement A. See section 3.2.3 for further information.

3.2.2 Mechanical Dimensions

VLT

®

HVAC Drive Instruction Manual 3 Mechanical installation

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

3-3

3

Accessory Bags: Find the following parts included in the adjustable frequency drive accessory bags

Frame sizes A1, A2 and A3 Frame size A5 Frame sizes B1 and B2 Frame sizes C1 and C2

Frame size B3 Frame size B4 Frame size C3 Frame size C4

1 + 2 only available in units with brake chopper. For DC link connection (load sharing) the connector 1 can be ordered separately (Code no. 130B1064)

An eight-pole connector is included in accessory bag for FC 102 without Safe Stop.

3.2.3 Accessory Bags

3 Mechanical installation VLT

®

HVAC Drive Instruction Manual

3-4

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

3

3.2.4 Mechanical mounting

All IP20 enclosure sizes as well as IP21/ IP55 enclosure sizes except A2 and A3 allow side-by-side installation.

If the IP 21 Enclosure kit (130B1122 or 130B1123) is used on enclosure A2 or A3,, there must be a minimum of 2 in [50 mm] of clearance between

drives.

For optimal cooling conditions, allow a free air passage above and below the adjustable frequency drive. See table below.

Air passage for different enclosures

Enclo-

sure:

A2 A3 A5 B1 B2 B3 B4 C1 C2 C3 C4

a (mm): 100 100 100 200 200 200 200 200 225 200 225

b (mm): 100 100 100 200 200 200 200 200 225 200 225

1. Drill holes in accordance with the measurements given.

2. You must provide screws suitable for the surface on which you want to mount the adjustable frequency drive. Re-tighten all four screws.

Table 3.2: Mounting frame sizes A5, B1, B2, B3, B4, C1, C2, C3 and C4 on a non-solid back wall, the drive must be provided with a backplate A due to

insufficient cooling air over the heatsink.

For heavier drives (B4, C3, C4), use a lift. First wall-mount the 2 lower bolts, then lift the drive onto the lower bolts. Finally, fasten the drive against the

wall with the 2 top bolts.

VLT

®

HVAC Drive Instruction Manual 3 Mechanical installation

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

3-5

3

3.2.5 Safety Requirements for Mechanical Installation

Pay attention to the requirements that apply to integration and the field mounting kit. Follow the information in the list to avoid serious

damage or injury, especially when installing large units.

The adjustable frequency drive is cooled by air circulation.

To protect the unit from overheating, it must be ensured that the ambient temperature

does not exceed the maximum temperature stated for the

adjustable frequency drive

, and that the 24-hour average temperature

is not exceeded

. Locate the maximum temperature and 24-hour average in the

paragraph

Derating for Ambient Temperature

.

If the ambient temperature is in the range of 113°–131°F [45°–55°C], derating of the adjustable frequency drive will become relevant, see

Derating for

Ambient Temperature

.

The service life of the adjustable frequency drive is reduced if derating for ambient temperature is not taken into account.

3.2.6 Field Mounting

For field mounting the IP 21/IP 4X top/,TYPE 1 kits or IP 54/55 units are recommended.

3.2.7 Panel Through Mounting

A Panel Through mount kit is available for adjustable frequency drive series VLT HVAC Drive, VLT Aqua Drive and .

In order to increase heatsink cooling and reduce panel depth, the adjustable frequency drive may be mounted in a through panel. Furthermore, the built-

in fan can then be removed.

The kit is available for enclosures A5 through C2.

NOTE!

This kit cannot be used with cast front covers. No cover or imminent plastic cover must be used instead.

Information on ordering numbers is found in the

Design Guide

, section

Ordering Numbers.

More detailed information is available in the

Panel Through Mount Kit instruction, MI.33.H1.YY,

where yy=language code.

3 Mechanical installation VLT

®

HVAC Drive Instruction Manual

3-6

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

3

4 Electrical installation

4.1 How to connect

4.1.1 Cables General

NOTE!

For the VLT HVAC Drive High Power series line power and motor connections, please see the VLT HVAC Drive

High Power Instruction

ManualMG.11.FX.YY

.

NOTE!

Cables General

All cabling must comply with national and local regulations on cable cross-sections and ambient temperature. Copper (140°–167°F

[60°–75°C]) conductors are recommended.

Details of terminal tightening torques.

Power (kW) Torque (Nm)

Enclo-

sure

200–240

V

380–480

V

525–600

V

Line pow-

er

Motor

DC connec-

tion

Brake Ground Relay

A2 1.1–3.0 1.1–4.0 1.8 1.8 1.8 1.8 3 0.6

A3 3.7 5.5–7.5 1.1–7.5 1.8 1.8 1.8 1.8 3 0.6

A5 1.1–3.7 1.1–7.5 1.1–7.5 1.8 1.8 1.8 1.8 3 0.6

B1 5.5–11 11–18.5 - 1.8 1.8 1.5 1.5 3 0.6

B2

-

15

22

30

-

4.5

2)

4.5

2)

3.7

3

0.6

B3 5.5–11 11–18.5 11–18.5 1.8 1.8 1.8 1.8 3 0.6

B4 11–18.5 18.5–37 18.5–37 4.5 4.5 4.5 4.5 3 0.6

C1 18.5–30 37 - 55 - 10 10 10 10 3 0.6

C2 37 - 45 75 - 90

-

14/24

1)

14/24

1)

14 14 3 0.6

C3 18.5–30 37 - 55 37 - 55 10 10 10 10 3 0.6

C4 30 - 45 55 - 90 55 - 90

14/24

1)

14/24

1)

14 14 3 0.6

D1/D3 - 110 - 132 110 - 132 19 19 9.6 9.6 19 0.6

D2/D4 - 160-250 160-315 19 19 9.6 9.6 19 0.6

E1/E2 - 315-450 355-560 19 19 19 9.6 19 0.6

F1–F4

3)

-

Table 4.1: Tightening of terminals

1) For different cable dimensions x/y, where x ≤0.147 in² [95 mm²] and y≥0.147 in² [95 mm²]

2) Cable dimensions above 25 hp [18.5 kW] ≥ 0.0542 in

2

[35 mm

2

] and below 30 hp [22 kW] ≤ 0.0155 in

2

[10 mm

2

]

3) For data on the F-series, please consult VLT

®

HVAC Drive High Power Instruction Manual, MG.11.F1.02

4.1.2 Fuses

Branch circuit protection

In order to protect the installation against electrical and fire hazard, all branch circuits in an installation, switch gear, machines, etc., must be short-circuit

and overcurrent protected according to the national/international regulations.

Short circuit protection

The adjustable frequency drive must be protected against short-circuit to avoid electrical or fire hazard. Danfoss recommends using the fuses mentioned

below to protect service personnel or other equipment in case of an internal failure in the unit. The adjustable frequency drive provides full short circuit

protection in case of a short circuit in the motor output.

VLT

®

HVAC Drive Instruction Manual 4 Electrical installation

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

4-1

4

Overcurrent protection

Provide overload protection to avoid fire hazard due to overheating of the cables in the installation. Overcurrent protection must always be provided in

accordance with national regulations. The adjustable frequency drive is equipped with internal overcurrent protection that can be used for upstream

overload protection (UL applications excluded). See par. 4-18

Current Limit

in the

VLT HVAC Drive Programming Guide

. Fuses must be designed for

protection in a circuit capable of supplying a maximum of 100,000 A

rms

(symmetrical), 500 V/600 V maximum.

Non-UL compliance

If UL/cUL is not to be complied with, Danfoss recommends using the fuses mentioned in the table below, which will ensure compliance with EN50178.

In case of malfunction, not following the recommendation may result in unnecessary damage to the adjustable frequency drive.

Non-UL compliance

Adjustable frequency

drive

Max. fuse size

Voltage Type

200–240 V

1K1-1K5

16A

1

200–240 V type gG

2K2

25A

1

200–240 V type gG

3K0

25A

1

200–240 V type gG

3K7

35A

1

200–240 V type gG

5K5

50A

1

200–240 V type gG

7K5

63A

1

200–240 V type gG

11K

63A

1

200–240 V type gG

15K

80A

1

200–240 V type gG

18K5

125A

1

200–240 V type gG

22K

125A

1

200–240 V type gG

30K

160A

1

200–240 V type gG

37K

200A

1

200–240 V type aR

45K

250A

1

200–240 V type aR

380–480 V

1K1

10A

1

380–500 V type gG

2K2-3K0

16A

1

380–500 V type gG

4K0-5K5

25A

1

380–500 V type gG

7K5

35A

1

380–500 V type gG

11K–15K

63A

1

380–500 V type gG

18K

63A

1

380–500 V type gG

22K

63A

1

380–500 V type gG

30K

80A

1

380–500 V type gG

37K

100A

1

380–500 V type gG

45K

125A

1

380–500 V type gG

55K

160A

1

380–500 V type gG

75K

250A

1

380–500 V type aR

90K

250A

1

380–500 V type aR

1) Max. fuses - see national/international regulations to select an appropriate fuse size.

Table 4.2: Non-UL fuses 200 V to 480 V

Circuit Breakers manufactured by General Electric, Cat. No. SKHA36AT0800, 600 V AC maximum, with the rating plugs listed below can be used to meet

UL requirements.

Size/Type

Rating plug catalog # Amps

P110 SRPK800A300 300

P132 SRPK800A350 350

P160 SRPK800A400 400

P200 SRPK800A500 500

P250 SRPK800A600 600

Table 4.3: Circuit Breaker Tables - D enclosures, 380–480 V

Size/Type

Bussmann PN* Rating Ferraz Siba

P250 170M4017 700 A, 700 V 6.9URD31D08A0700 20 610 32.700

P315 170M6013 900 A, 700 V 6.9URD33D08A0900 20 630 32.900

P355 170M6013 900 A, 700 V 6.9URD33D08A0900 20 630 32.900

P400 170M6013 900 A, 700 V 6.9URD33D08A0900 20 630 32.900

Table 4.4: E enclosures, 380–480 V

4 Electrical installation VLT

®

HVAC Drive Instruction Manual

4-2

MG.11.A9.22 - VLT

®

is a registered Danfoss trademark

4

Page is loading ...

Danfoss VLT HVAC Drive FC 102 Operating instructions

This manual is also suitable for

Danfoss VLT HVAC Drive FC 102 Operating instructions

Related papers

Other documents