SEI FA982500TX Installation guide

For assistance with assembly, contact:

Southern Enterprises Inc.

Customer Service 1-800-633-5096

[email protected]

www.seidal.com

FA982500TX

Moreno Fireplace Tower

-Mission Oak

Assembly Instructions

PO#:

A

Quantity of 1

Top Panel

B

Quantity of 1

Left Side Panel

C

Quantity of 1

Right Side Panel

D

Quantity of 1

Upper Back Panel

E

Quantity of 1

Fixed Shelf Panel

F

Quantity of 1

Bottom Panel

G

Quantity of 1

Bottom Cross Panel

H

Quantity of 2

Cross Panel

I

Quantity of 2

Vertical Panel

J

Quantity of 1

Back Panel

K

Quantity of 1

Adjustable Shelf Panel

L

Quantity of 2

Support Rail

M

Quantity of 2

Wood Block

1

Quantity of 28

Cam Bolt ∮9/32”x1-1/2”L

2

Quantity of 28

Cam Lock ∮5/16”x1/2”L

3

Quantity of 28

Wood Dowel 5/16” x1-1/2”L

4

Quantity of 5

Screw ∮5/32”x1”L

5

Quantity of 4

Bolt ∮1/4”x1-1/4”L

6

Quantity of 4

Lock Washer ∮1/4”

Moreno Fireplace Tower-Mission Oak

Parts List

Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface

like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing. Before

beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures. Using the

incorrect hardware will cause damage.

.

7

Quantity of 4

Flat washer ∮1/4”x3/4”

8

Quantity of 1

Allen Wrench 1/4”

9

Quantity of 7

Screw ∮5/32”x1-1/4”L

10

Quantity of 14

Screw ∮1/8”x1/2”L

11

Quantity of 4

Shelf Holder

12

Quantity of 2

Anti-Tipping Hardware

13

Quantity

of 1

Firebox (in a separate carton)

Care and Cleaning Instructions:

Before using, wipe with a clean, dry cloth.

Periodically apply furniture wax to renew

the finish. Avoid rubbing or scratching the

surface with rough or abrasive objects.

For replacement parts or questions, please

call customer service at 1-800-633-5096.

Assembly Tool Required

No.2 Phillips Screwdriver

(not included)

Figure 1

Do not over tighten cam bolts,

please stop when you feel them tighten.

Insert cam locks (2) into holes on

vertical panel (I).

Screw cam bolts (1) into holes on right

side panel (C). Attach vertical panel (I)

to right side panel (C) by inserting wood

dowel (3) and cam bolts (1) into

corresponding holes until vertical panel

(I) and right side panel (C) meet.

Tighten by rotating cam locks (2)

clockwise with Phillips screwdriver.

Figure 2

Insert cam locks (2) into holes on

vertical panel (I).

Screw cam bolts (1) into holes on left

side panel (B). Attach vertical panel (I)

to left side panel (B) by inserting wood

dowel (3) and cam bolts (1) into

corresponding holes until vertical panel

(I) and left side panel (B) meet.

Tighten by rotating cam locks (2)

clockwise with Phillips screwdriver.

Moreno Fireplace Tower- Mission Oak

Assembly Instructions

( 2)

(1)

Figure 3

Insert cam locks (2) into holes on cross

panel (H).

Screw cam bolts (1) into holes on top

panel (A). Attach cross panel (H) to top

panel (A) by inserting wood dowel (3)

and cam bolts (1) into corresponding

holes until cross panel (H) and top

panel (A) meet.

Tighten by rotating cam locks (2)

clockwise with Phillips screwdriver.

Use screw (4) and wood dowels (3) to

connect top panel (A) to upper back

panel (D).

Tighten screw (4) with Philip

screwdriver.

Figure 4

Insert cam locks (2) into holes on cross

panel (H).

Screw cam bolts (1) into holes on fixed

shelf panel (E). Attach cross panel (H)

to fixed shelf panel (E) by inserting

wood dowels (3) and cam bolts (1) into

corresponding holes until cross panel

(H) and fixed shelf panel (E) meet.

Tighten by rotating cam locks (2)

clockwise with Phillips screwdriver.

Use screws (9) and wood dowels (3) to

connect support rails (L) to shelf panel

(E).

Tighten screws (9) with Philips

screwdriver.

Figure 5

Use screws (9) and wood dowels (3) to

connect bottom cross panel (G) to

bottom panel (F).

Tighten screws (9) with Philips

screwdriver.

Figure 6

Insert cam locks (2) into holes on

assembled unit from figure 3 and

assembled unit from figure 5.

Screw cam bolts (1) into holes on right

side panel (C).

Attach assembled unit from figure 3 and

assembled unit from figure 5 to right

side panel (C) by inserting wood dowels

(3) and cam bolts (1) into corresponding

holes until assembled unit from figure 3,

assembled unit from figure 5, and right

side panel (C) meet.

Tighten by rotating cam locks (2)

clockwise with Phillips screwdriver.

Use bolts (5), lock washers (6), flat

washers (7), and wood dowels (3) to

connect assembled unit from figure 4 to

right side panel (C).

Tighten bolts (5) with Allen wrench (8).

Figure 7

Repeat last step to attach left side panel

(B) to assembled unit from figure 6.

Figure 8

Attach back panel (J) to assembled unit

with screws (10).

Tighten screws (10) with Phillips

screwdriver.

Insert firebox (13) into the back of the

unit. Make sure the firebox is pressed

tightly against the unit.

Attach wood blocks (M) to assembled

unit.

Use screws (4) to connect wood blocks

(M) to support rails.

Tighten screws (4) with Philips

screwdriver.

Figure 9

Insert shelf holders (11) into holes on

side panels.

Place adjustable shelf (K) onto the shelf

holder (11).

Make sure the shelf holder (11)

holds the shelf (K) firmly.

Figure 10

Attach anti-tipping hardware (12)

to the back of the upper back panel

(D) as shown in figure 10.

Tighten screws using Philips

screwdriver.

Mark two desired locations on wall and

drill two 3/16" holes.

Then, Insert plastic anchors into the two

holes on wall as shown. Attach the

anti-tipping hardware to the wall using

screws as shown.

Finally, move item close to the wall and

secure with plastic straps

Anti-tipping hardware must be used for

this product to avoid tipping and injury.

Figure 11

Now your Moreno fireplace tower is

ready for use.

Please immediately examine this product carefully. Any request for missing parts or damage replacement must

be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this

time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying

product(s) and we are not responsible for any damages due to product modification(s).

If damages or missing

parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement

merchandise.

Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central

time if you have product issues or email us at servi[email protected]. Please ask for customer service

representative for issues involving damages or replacement parts. Please ask for technical assistance

representative for any issues with product and assembly/construction.

Please contact the retailer that you purchased from for returns.

Customer Information

Name

Address

City/State/Zip Code

Phone Number

Please indicate where you purchased this item: Store/Website/Catalog

Please indicate color/size/style number:

Style No Parts Letter Parts Description Quantity Needed

Parts Replacement Form

Customer Service 1-800-633-5096

service@seidal.com

Southern Enterprises, Inc.

600 Freeport Parkway, Suite 200

Coppell, Texas 75019

SEI FA982500TX Installation guide

This manual is also suitable for

SEI FA982500TX Installation guide

Related papers

Other documents