Safety Vision SV-CLCD56B1 Troubleshooting Manual
- Category
- Car video systems
- Type
- Troubleshooting Manual
COLLISION AVOIDANCE CAMERA SYSTEMS
Copyright © 2008 Safety Vision, L.P. All Rights Reserved.
05/08
CORPORATE HEADQUARTERS
6100 W. Sam Houston Pkwy. N.
Houston, TX 77041-5113
Toll Free: 800.880.8855
Main: 713.896.6600
Fax: 713.896.6640
ww w.safety vision.com
FCC Compliance Statement
This device has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equip-
ment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference
in which case the user will be required to correct the interference at his own
expense.
Any changes or modications in construction of this device which are not
expressly approved by the party responsible for the compliance could void
the user’s authority to operate the equipment.
NOTE
CAUTION
Important Notices
Title: Rear Vision System Troubleshooting Guide for SV-CLCD56B1
Safety Vision attempts to provide information contained in this manual
based on the latest product information available at the time of publication.
However, because of Safety Vision’s policy of continual product improvement,
Safety Vision reserves the right to amend the information in this document at
any time without prior notice.
This material is condential and the property of Safety Vision. It is shared with
your company for the sole purpose of helping you with the operation of the
described equipment.
Safety Vision makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
tness for a particular purpose. Safety Vision shall not be liable for errors
contained herein or for incidental or consequential damages in connection
with the furnishing, performance, or use of this material.
Safety Vision expressly disclaims all responsibility and liability for the
installation, use, performance, maintenance, and support of third-party
products. Customers are advised to make their independent evaluation of
such products.
No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Safety Vision.
Safety Vision® is a registered trademark of Safety Vision, LP. All other products or
name brands mentioned in this document are trademarks of their respective
owners. For more information about Safety Vision and its products, go to
www.safetyvision.com or call 800-880-8855.
The Power Led is on, but no picture is displayed.
Check that the green wire is connected to the back-up light circuit and is
1.
receiving 12V.
If there is still no picture OR there is a white screen OR picture comes on
2.
then goes o in less than ten (10) seconds, return the unit for service. See
page 10.
Troubleshooting: The Power LED is on (cont.)
There is no audio.
Check that the yellow wire is receiving 12V.
1.
If there is still no audio, return the unit for service. 2. See page 10.
Troubleshooting: There is no audio
The SV-CLCD56B1 is unique to other Rear Vision Systems in that it
has seperate green and yellow wires for video and audio triggers,
respectively.
SV- LCD56B1 System Features
Monitor
5.6-inch TFT LCD screen•
Wide eld of view•
Integrated speaker•
Camera
Rugged, water-resistant housing•
CCD image sensor for improved image quality•
Wide eld of view (135• ⁰ diagonal, 108⁰ horizontal)
LEDs that generate infrared light for improved image quality in low-light •
situations
Integrated microphone•
Control Box
Provides DC power to the monitor and camera•
1 audio/video input•
1 audio/video output•
4 9
Contents
SV-CLCD56B1 System Features ........................................................................................... 4
Monitor Controls ...................................................................................................................... 5
Tools Required for Troubleshooting .................................................................................. 7
Operating and Troubleshooting Instructions ................................................................ 7
Troubleshooting Procedures ............................................................................................... 8
Returning the Unit for Service............................................................................................10
FCC Compliance Statement ............................................................................................... 11
Return the SV-CLCD56B1 for service when:
Previous troubleshooting owcharts do not solve the problem.•
After comrming the • Color, Contrast, and Brightness controls are properly
adjusted, the monitor displays solid white.
The picture comes on and then goes o within ten (10) seconds time.•
To return the unit for service:
Call Technical Support at
1. 800-880-8855.
Speak to a Technical Support Representative.
2.
Obtain an 3. RMA Number and any additional special instructions.
Carefully pack the unit, including all defective parts and a note that
4.
includes the RMA Number and a detailed description of the issue
experienced.
Ship to:
5.
Safety Vision
Technical Support RMA# _______________
6100 West Sam Houston Parkway North
Houston, TX 77041
Returning the Unit for Service
310
1) POWER LED
Indicates that the monitor has power. The LED glows red when the monitor
is receiving power, but is not turned on (Stand By Mode). The LED switches o
when the LCD screen is turned on.
2) DAY/NIGHT SENSOR
Senses available light and adjusts monitor volume accordingly.
3) MENU BUTTON
Press to cycle through Color, Contrast, Brightness, Volume, and Language menus.
Use the + and - Buttons to adjust each setting.
4) + BUTTON
Press this button to increase Menu values.
5) - BUTTON
Press this button to decrease Menu values.
The monitor’s Power LED is not on.
Check the fuse located on the red wire.
1. See picture below.
Check for 12V at the end of the red wire.
2.
Conrm black wire is connected to a good ground on the chassis.3.
If there is voltage on the red wire and the black wire is connected properly, 4.
return the unit for service. See page 10.
Troubleshooting: The Power LED is not on
The Power LED is on, but no picture is displayed.
Check the pins inside the Monitor Input/Power Connector and all other
1.
connectors. If there are any pins damaged or missing return unit for
service.
Conrm the Monitor Input/Power Connector is rmly connected to the
2.
proper Control Box Connector.
If there is still no picture, see the next procedure on the following page.
3.
Troubleshooting: The Power LED is on
Monitor Input/Power Connector
Fuse
Monitor Controls
8 5
6) POWER BUTTON
Press once while in Stand By Mode to turn monitor on. When on, press once to
cycle through C A1, CA2, and AUX inputs. Press and hold to return monitor to
Stand By Mode.
7) NORMAL/MIRROR SWITCH
Press to switch monitor image to display Normal or Reverse (as it would appear
in a rear-view mirror).
8) MONITOR INPUT/POWER CONNECTOR
Supplies both power and image input to the monitor.
9) BRACKET SLOT
Accepts the adjustable monitor mounting bracket.
Tools Required for Troubleshooting
DVM (Digital Voltmeter, set to DC)•
Fuse Puller•
Operating and Troubleshooting Instructions
When you turn the ignition key to the accessory or on position, power is sup-
plied to the monitor. The system will turn on automatically when the vehicle
is shifted into reverse. Pushing the Power Button will also manually activate
the system, which allows the operator to use the system while driving. The
green LED on the monitor will illuminate at that time.
Conrm the Color, Contrast, and Brightness settings are properly adjusted if pos-
sible. Access these settings by pressing the Menu Button.
Note the power of the monitor:
When you push the power switch to the Stand By Mode position, the monitor
is placed in a Stand By Mode mode. The monitor is not turned o until the igni-
tion key is in the o position.
See the following three pages for these conditions:
If the Power LED is NOT on - see procedure on page 8.•
If the Power LED is on - see procedure on pages 8 and 9.•
If no audio is received - see procedure on page 9.•
If the screen is completely white, or the picture comes on and •
goes o within 10 seconds - see instructions for returning unit
for service on page 10.
76
-
1
-
2
-
3
-
4
-
5
-
6
Safety Vision SV-CLCD56B1 Troubleshooting Manual
- Category
- Car video systems
- Type
- Troubleshooting Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Safety Vision 70RP User guide
-
-
-
-
-
-
Safety Vision Observer 4120 User guide
-
-
Safety Vision Observer 4816 NVR User guide
-