Pittsburgh Automotive Item 56183 Owner's manual

Brand: Pittsburgh Automotive

Model: Item 56183

Type: Owner's manual

This manual is also suitable for

56183

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back

of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep

this manual and the receipt in a safe and dry place for future reference. 19h

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

2018 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

To ols required for assembly and se rv ic e m ay n ot b e i nc lu de d .

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 56183

SPECIFICATIONS TABLE

Sizes Inner Diameter Outer Diameter Length

Receiving Cup

1-3/4″ 2-1/8″ 1/2″

1-7/8″ 2-1/4″ 7/16″

Installing Tube

1-3/4″ 2″ 2-3/8″

1-3/4″ 2″ 3″

Remover / Installer 3/4″ 1-7/16″ 1″

Receiving Tube

2″ 2-1/4″ 2″

2-1/4″ 2-1/2″ 1-1/2″

2-1/4″ 2-1/2″ 3/4″

2-1/4″ 2-1/2″ 2-3/4″

2-3/4″ 3″ 2-1/4″

2-7/16″ 2-3/4″ 2-1/4″

2-5/8″ 2-7/8″ 2-7/8″

2-3/16″ 2-7/16″ 3-3/16″

Applications

Most GM

, Ford

, and Dodge

2 & 4 WD Pickups,

Vans, and SUV’s through 1997

Material Forged, heat treated and machined carbon steel

Screw Plug Size 7/8″ O.D. x 3″ Long

Important Safety Information

1. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

2. Keep children and bystanders away

while using this product. Distractions

can cause you to lose control.

3. Stay alert, watch what you are

doing and use common sense when

using this product. Do not use this

product while you are tired or under

the influence of drugs, alcohol or

medication. A moment of inattention

while using this product may result

in serious personal injury.

4. Use safety equipment. Always wear

eye protection. Safety equipment

such as non-skid safety shoes,

hard hat, or heavy duty work gloves

used for appropriate conditions

will reduce personal injuries.

5. Do not overreach. Keep proper

footing and balance at all times.

This enables better control of this

product in unexpected situations.

6. Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewelry or long

hair can be caught in moving parts.

7. Do not force this product. Use the

correct product for your application.

The correct product will do the

job better and safer at the rate

for which it was designed.

Page 3For technical questions, please call 1-888-866-5797.Item 56183

8. Store this product out of the reach

of children and do not allow people

unfamiliar with the product or these

instructions to operate the product.

This product could be dangerous

in the hands of untrained users.

9. Maintain this product. Check for

misalignment or binding of parts,

breakage of parts and any other

condition that may affect the

product’s operation. If damaged,

have this product repaired before

use. Many accidents are caused

by poorly maintained equipment.

10. Use this product in accordance with

these instructions and in the manner

intended for this particular type of

product, taking into account the

working conditions and the work to

be performed. Use of this product for

operations different from those intended

could result in a hazardous situation.

11. Maintain labels and nameplates

on the Adapter Set. These carry

important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

12. Wear ANSI-approved safety

goggles and heavy duty work

gloves when using this product.

13. Prior to servicing a vehicle, turn off

the vehicle’s engine and refer to

the vehicle manufacturer’s service

and repair manual for instructions

on how to safely secure the vehicle

in place with jacks, stands, etc.

14. The warnings, precautions, and

instructions discussed in this instruction

manual cannot cover all possible

conditions and situations that may

occur. It must be understood by the

operator that common sense and

caution are factors which cannot

be built into this product, but must

be supplied by the operator.

Operating Instructions

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of

this document including

all text under subheadings

therein before set up or

use of this product.

Attaching Plug Bolt to C-Frame

NOTE: This set is recommended

for use with 4065 4-Wheel Drive

Ball Joint Service Kit, which is also

available from Harbor Freight Tools.

1. The illustration in Figure A below

depicts a disassembled C-Frame, a

tool that is part of 4065 Service Kit.

2. To operate Master Ball Joint Adapter

Set, attach the Plug Bolt (part 14)

to the C-Frame from 4065.

3. To do so, unscrew and remove

the Forcing Screw, Steel Ball,

and O-Ring from the C-Frame.

Steel Ball / O-Ring

(not included)

Forcing

Screw

(not included)

Plug Bolt (14)

C-Frame

(Part of 4065)

Figure A

Page 4 For technical questions, please call 1-888-866-5797. Item 56183

4. Make sure Steel Ball and O-Ring

remain inside the Forcing Screw. Then

insert Plug Bolt into Forcing Screw.

5. Screw threaded end of Forcing Screw,

with its Steel Ball, O-Ring, and

attached Plug Bolt back into

threaded end of C-Frame toward

unthreaded hole of C-Frame.

Removing a Ball Joint

NOTE: The following instructions apply

to most GM

, Ford

, and Dodge

2 and

4 wheel drive pickups, vans, and SUV’s

through 1997 (see charts on pages 6

through 9). The instructions are intended to

illustrate the process in general terms, and

NOT to be specific to any one make/model

vehicle. A combination of Receiving Tubes

(parts 1-6 and 10-11), Receiving Cups

(parts 7-12), and Installing Tubes (parts

8-9), will be necessary for different vehicles.

1. Remove all attaching

hardware from ball joint.

2. Mount Remover/Installer (13) on

Forcing Screw assembly so that

larger diameter portion of Remover/

Installer faces threaded hole of

C-Frame, and smaller diameter

portion faces unthreaded side of

ball joint. (See Figure B below.)

3. Mount proper size Receiver Tube

over threaded side of ball joint.

4. Align mounted Remover/Installer,

ball joint, and Receiver Tube to

allow removal of ball joint.

5. Using a wrench, turn Forcing Screw

assembly clockwise to remove ball joint.

C-Frame

(Part of 4065)

Forcing

Screw

(not included)

Plug Bolt (14)

Remover /

Installer (13)

Receiver Tube

(1-6, 10-11)

Figure B

Page 5For technical questions, please call 1-888-866-5797.Item 56183

Installing a Ball Joint

1. Mount Remover/Installer (13) on

Forcing Screw assembly so that the

larger diameter portion of Remover/

Installer faces the threaded hole of

C-Frame and smaller diameter portion

faces the unthreaded side of ball joint.

2. Place mounted Remover/Installer

on unthreaded side of ball joint.

3. Align mounted Remover/

Installer, ball joint, and proper

size Receiver Tube (1-6, 10-11)

to allow installation of ball joint.

4. Using a wrench, turn Forcing

Screw assembly clockwise

to install the ball joint.

Maintenance and Servicing

1. Before each use, inspect general

condition of tool. Check for

misalignment or binding of moving

parts, cracked or broken parts,

and any other condition that may

affect its safe operation. Do not

use damaged equipment.

2. After use, clean external surfaces.

Then dry and lubricate all moving

parts. Do not use solvents.

3. When storing, keep Ball Joint

Adapter Set and its accessories

in its Carrying Case and store

in a clean, dry, safe location.

4. CAUTION! All maintenance, service,

and repairs not mentioned in this

manual must only be performed by

a qualified service technician.

Page 6 For technical questions, please call 1-888-866-5797. Item 56183

BALL JOINT ADAPTER APPLICATIONS

U = Upper, L = Lower,

R = Remove, I = Install

Part Numbers Below Illustrated on Page 10

Upper/

Lower

Vehicle

1 2 3 4 5 6 7 8 9 10 11 12 13 14

FORD

L 1986-97 AEROSTAR I

U 1987-88 2WD BRONCO II I

U 1989-90 2WD BRONCO II I I

L 1989-90 2WD BRONCO II I

1991-94 2WD

EXPLORER

I I

1991-94 2WD

EXPLORER

U 1983-88 2WD RANGER I

U 1989-97 2WD RANGER I I

1987-96 2WD 1/2-Ton

Pickup

R I I R

1997 2WD & 4WD

1/2-Ton Pickup

I R I

1987-97 2WD 3/4-, 1-Ton

Pickup

R I I R

1981-86 2WD 1/2-Ton

Pickup

1981-86 2WD 1/2-Ton

Pickup

I I R

1990 4WD BRONCO II

with Dana 28

U 1984-89 4WD BRONCO II I

L U 1980-96 4WD BRONCO I I R

1991-94 4WD

EXPLORER with Dana 28

1991-97 4WD RANGER

with Dana 28

U 1983-89 4WD RANGER I

L U 1980-96 4WD BRONCO I I R

1981 4WD 1-Ton

(3800 axle)

I I R

1980-96 4WD 1/2-, 3/4-

Ton

I I R

1987-97 2WD 1/2-, 3/4-

Ton

I I R I

1992-97 2WD 1/2-, 3/4-,

1-Ton Van

R I R

Page 7For technical questions, please call 1-888-866-5797.Item 56183

1992-97 2WD 1/2-Ton

Van

1992-97 2WD 3/4-, 1-Ton

Van

R I

1984-89 4WD BRONCO

1990 4WD BRONCO II

with Dana 28

L U

1990 4WD BRONCO II

with Dana 35

1991-93 4WD

EXPLORER with Dana

1990-93 4WD RANGER

with Dana 35

U 1992-97 4WD 1-Ton I I R

1980-96 4WD 1/2-, 3/4-,

1-Ton (IFS)

I I R

L U

1993-94 4WD

EXPLORER with Dana

L U

1993-97 4WD RANGER

with Dana 35

1996-97 4WD 1-Ton with

Solid Axle

I I R I

1980-95 4WD 3/4-, 1-Ton

Spindle

I I R I

BALL JOINT ADAPTER APPLICATIONS

U = Upper, L = Lower,

R = Remove, I = Install

Part Numbers Below Illustrated on Page 10

Upper/

Lower

Vehicle

1 2 3 4 5 6 7 8 9 10 11 12 13 14

FORD (CONTINUED)

Page 8 For technical questions, please call 1-888-866-5797. Item 56183

BALL JOINT ADAPTER APPLICATIONS

U = Upper, L = Lower,

R = Remove, I = Install

Part Numbers Below Illustrated on Page 10

Upper/

Lower

Vehicle

1 2 3 4 5 6 7 8 9 10 11 12 13 14

DODGE / CHRYSLER / PLYMOUTH

L 1987-97 2WD DAKOTA R I I R

1972-93 1/2-, 3/4-Ton

2WD Pickup

R I I R

1974-93 1/2-Ton 2WD

RAMCHARGER

R I I R

1979-97 1/2-, 3/4-, 1-Ton

2WD Van

R I I R

1972-93 2WD 3/4-, 1-Ton

Pickup

I R

L 1979-97 1-Ton 2WD Van I R

1984-96 CARAVAN,

VOYAGER, TOWN &

COUNTRY

1994-97 2WD 1/2-, 3/4-,

1-Ton Pickup (IFS)

1994-97 2WD 1/2-, 3/4-,

1-Ton Pickup (IFS)

1994-97 2WD 1-Ton Solid

Axle

I I

1994-97 2WD 1-Ton Solid

Axle

I I R I

1994-97 3/4-, 1-Ton Dana

60 Axle, 4WD

I I

1994-97 3/4-, 1-Ton Dana

60 Axle, 4WD

I I R I

L U

1994-97 1/2-, 3/4-Ton

DANA 44 Axle, 4WD

R I I R

1972-93 1/2-, 3/4-, 1-Ton

4WD & RAMCHARGER

R I I R

1972-93 1/2-, 3/4-, 1-Ton

4WD & RAMCHARGER

I I R

Page 9For technical questions, please call 1-888-866-5797.Item 56183

JEEP

1 2 3 4 5 6 7 8 9 10 11 12 13 14

L U

1993-97 2WD GRAND

CHEROKEE

R I I R

L U

1993-95 4WD GRAND

CHEROKEE,

GRAND WAGONEER

R I I R

1987-97 4WD

WRANGLER

R I I R

1984-95 4WD

CHEROKEE,

WAGONEER

R I I R

1990-97 2WD

CHEROKEE,

COMANCHE,

WAGONEER

R I I R

1990-97 4WD

WRANGLER

R I I R

1990-95

2WD & 4WD

CHEROKEE,

COMANCHE

WAGONEER

R I I R

1984-97 2WD

CHEROKEE, COMANCHE,

WAGONEER

R I I R

1984-89 2WD

CHEROKEE,

COMANCHE,

WAGONEER

R I I R I

1987-89 4WD

WRANGLER

R I I R I

1984-89 4WD

CHEROKEE,

COMANCHE, WAGONEER

R I I R I

L U

1984-92 Full Size 4WD

GRAND WAGONEER

I I R

L U

1972-88

4WD Truck, CJ,

Full

Size CHEROKEE

WAG-

ONEER

I I R

BALL JOINT ADAPTER APPLICATIONS

U = Upper, L = Lower,

R = Remove, I = Install

Part Numbers Below Illustrated on Page 10

Upper/

Lower

Vehicle

1 2 3 4 5 6 7 8 9 10 11 12 13 14

GENERAL MOTORS

1982-97 2WD S-10

BLAZER, Jimmy, Pickup

I R I

1985-97 ASTRO SAFARI

Van

1973-95 2WD 1/2-,

3/4-Ton G Van

1996-97 4WD 1/2-, 3/4-,

1-Ton

R I I

Page 10 For technical questions, please call 1-888-866-5797. Item 56183

Parts List and Diagram

Parts List

Part Description Qty

1 Receiving Tube 1

2 Receiving Tube 1

3 Receiving Tube 1

4 Receiving Tube 1

5 Receiving Tube 1

6 Receiving Tube 1

7 Receiving Cup 1

8 Installing Tube 1

Part Description Qty

9 Installing Tube 1

10 Receiving Tube 1

11 Receiving Tube 1

12 Receiving Cup 1

13 Remover / Installer 1

14 Plug Bolt 1

15 Carrying Case (not shown) 1

PLEASE READ THE FOLLOWING CAREFULLY

NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION

OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED

TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED

TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL

PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF

HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 11For technical questions, please call 1-888-866-5797.Item 56183

Assembly Diagram

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability

standards, and warrants to the original purchaser that this product is free from defects in materials

and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to

damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside

our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.

We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,

special or consequential damages arising from the use of our product. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion

may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Pittsburgh Automotive Item 56183 Owner's manual

Brand: Pittsburgh Automotive

Model: Item 56183

Type: Owner's manual

This manual is also suitable for

56183

Download PDF

report

Pittsburgh Automotive Item 56183 Owner's manual

This manual is also suitable for

Pittsburgh Automotive Item 56183 Owner's manual

Related papers

Other documents