Cadillac Prodigy One.2 Installation guide

Brand: Cadillac

Model: Prodigy One.2

Category: Video switches

Type: Installation guide

Prodigy One.2

Installation

TD-CADICTS-KIT

Manual

www.intraphex.com

support@intraphex.com

Support: 810.355.2266

Fax: 810-735-0175

Contacts

 Dash Pad Bracket

 Prodigy One.2

 Monitor

 Prodigy One Data Cable

 CTS Radio T-Harness

 AV input Cable

 4 Pin Touch Cable

 Multi Display PCB

& Connectors

 Bag of Screws & Clips

 Stereo Aux in Cable

Contents

Remove center console trim bezels. use hook tool to release panel from

rear. Place panels in safe locaon to assure they don’t get scratched.

Remove gear selector trim bezel. Use hook tool to release panel from

rear. Place panel in a safe locaon.

Place shier into “Neutral” (g A), pull gear selector trim bezel away from

radio dash bezel (g B),

Remove two 7mm screws at the lower le and right of the radio dash

bezel (g c).

Remove shown plasc trim. Use hook too to pull from noted area.

Remove shown plasc trim. Use hook tool to pull from noted area.

Use cauon not to break plasc tabs.

Remove radio dash bezel. Use cauon and unplug all connecons from

back of panel.

Remove four 7mm screws from front panel of disc changer.

Remove changer assembly and unplug all plugs from rear.

Install INTRAPHEX supplied “T-harness”, route wires as necessary to

ensure that changer assembly can be installed back into locaon.

Plug male end of INTRAPHEX supplied “T-harness” into rear of changer

assembly and reinstall antenna plugs.

Replace changer assembly and re-install four 7mm screws.

Please refer to wiring diagram in back of manual for reference

Connect 12 volt acc wire. Use Mul-meter to test. Located at BCM,

green plug PIN 6, pink wire.

Insert INTRAPHEX supplied T-nuts into empty locaons shown.

Next we will remove the OEM radio LCD, and preset buons.

Remove eight #1 screws securing the panel in place.

Gently pull the radio lcd away from dash bezel.

Remove four remaining #1 screws from lcd assembly

Remove preset buons from lcd.

Remove two #1 screws.

Separate buons from bezel.

Add buons to INTRAPHEX supplied trim bezel, route wires accordingly.

Replace two #1 screws.

Replace six #1 screws to ax INTRAPHEX supplied trim bezel to the radio

panel. Replace preset buon plug. Replace clock harness with Intraphex

supplied harness for dimming feature.

Assembled dash panel with INTRAPHEX supplied bezel.

Factory dash pad.

Remove t-10 torx screws to separate two pieces.

Align dash pad with INTRAPHEX supplied monitor bracket.

Use provided screws to aach dash pad to bracket.

Assembled dash pad bracket.

Aach dash pad bracket to monitor assemble using INTRAPHEX

provided screws. Long screws go in back of monitor and short ones go in

side of monitor. Steps 31 and 32 can be done aer car is re-assembled if

you nd it easier.

With monitor assembly in the up posion install two black INTRAPHEX

provided dash pad bracket rear set screws. Steps 31 and 32 can be done

aer car is re-assembled if you nd it easier.

Assembled monitor assembly

Install INTRAPHEX provided harnesses into monitor assembly.

Route cables accordingly and install monitor assembly into dash. Use

INTRAPHEX provided screws to secure into dash.

Plug in the two plugs from the preset buon panel.

Replace radio control panel.

Replace two 7mm screws.

Replace shier trim bezel.

Replace dash trim.

Replace dash trim.

Replace center console trim bezel

Ignion (pin 6, pink @ green plug in

BCM

Reverse (pin 3, lt green @ grey plug in

BCM

A/V input (use AUX on radio)

Camera Input

For SRX only

For CTS only

SPEAKER

***NOTE***

Please be sure to set the dip switches for video input according to the chart. Not seng the

dip switches correctly may render the prodigy one.2 or the video one inputs inoperave.

Scan the QR code above to see a short video on the operaon of the

Cadillac PRODIGY ONE.2 kit.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

Cadillac Prodigy One.2 Installation guide

Brand: Cadillac

Model: Prodigy One.2

Category: Video switches

Type: Installation guide

Other documents