Page 1 of 5 AR-B1893 Manual Part: 220010258
AR-B1893 MANUAL
Version 1.1
1. SETTING UP THE SYSTEM
TOP PLACEMENT
BOTTOM PLACEMENT
1.1 SO-DIMM DDR-SDRAM SOCKET 200
PIN (SODIMM1)
1.2 HARD DISK (IDE1 & IDE2) & CF
CONNECTOR (CFD1)
Note: If IDE2 & CFD1 both in used, CFD1 must be as “Master” & IDE2
is as “Slave”.
1.3 VGA CONNECTOR
1.4 KEYBOARD / MOUSE CONNECTOR
Page 2 of 5 AR-B1893 Manual Part: 220010258
1.5 POWER CONNECTOR
1.6 CMOS JUMPER
1.7 USB PORT
• USB1 (Port0 & Port1)
• USB3 Pin Header (Port2 & Port3)
1.8 SERIAL PORT
COM1: RS-232
COM2: RS232 / RS-422 / RS-485
Note: If CN6 in used, COM2 can’t be used
1.9 FAN CONNECTOR (CPUF1, CPUF2, CPUF3)
1.10 INTERNAL BUZZER (BZ1)
1.11 ETHERNET RJ-45 (LAN1, LAN2, LAN3,
LAN4)
: Link LED
: Act LED
: Link LED
: Act LED
1.12 RESET BUTTON
Page 3 of 5 AR-B1893 Manual Part: 220010258
1.13 ATX POWER (ATX1)
1.14 MINI PCI SLOT (MPCI1)
1.15 PCI SLOT (PCI1)
1.16 ISP CPLD CONNECTOR (CN1)
1.17 GPIO PORT (CN2)
1.18 JUMPER & PIN HEADER
Page 4 of 5 AR-B1893 Manual Part: 220010258
2.0 WATCH DOG TESTING
2.1 GPIO TESTING
2.2 LCD DISPLAY TESTING
Page 5 of 5 AR-B1893 Manual Part: 220010258
2.3 ETHERNET MAC ADDRESS
PROGRAMMING
2.3.1 BCM4401 Ethernet:
Program the eeprom in engineering
mode
(1) Boot from DOS (Win 98 preferred) and
type b44diag –b44eng
(2) 0:>sromutil –m 001018000001 14e4
8401. MAC address 001018000001,
SVID:14e4 and SID:8401 will be
programmed into eeprom. You can change
to other values if nevessary.
(3) 0:>sromutil –b 0. Disable PXE function
on NIC if PXE binary image is being
integrated into BIOS.
(4) 0:>sromutil –d –feeprom.bin, you will get
your golden eeprom.bin file
(5) Exit to DOS
(6) Re-boot the system
(7) Under engineering mode, customers can
see a list of all commands by typing “help”
after 0:>. In addition, for all parameters,
please type 0:>command ? (for example
0:>secfg ?, and you should get a list of all
parameters associated with that specific
command),
2.3.2 BCM5788 Ethernet:
Program the eeprom in engineering
mode
(1) Boot from DOS (Win 98 preferred) and
type b57diag -b57eng
(2) Please make sure HIMEN.SYS and
COMMAND.COM are also included on the
floppy.
(3) 0:>seprg –fee5788c3.26
(4) 0:>secfg and change the settings (for
example 1=00:10:18:12:34:56 to change
MAC address. 24=1 to enable ASF).
Remember to save the settings and write
back to EEPROM. Please see page 4 for
the complete list of EEPROM setting.
(5) For LOM applications, please modify
item 30 under settings to 1 (from NIC to
LOM)
(6) 0:>sedump -f=eeprom.bin -l=xxxx (file
size of eeprom.bin), you will get the golden
eeprom.bin file
(7) Exit to DOS
(8) Under engineering mode, customers can
see a list of all commands by typing “help”
after 0:>. In addition, for all parameters,
please type 0:>command ? (for example
0:>secfg ?, and you should get a list of all
parameters associated with that specific
command).
/
