protech ProX-1635LF User manual

USER’S

MANUAL

ProX-1635LF

For Socket 370

Half-size CPU Card

With VGA / LAN

Prox-1635LF M2

Copyright Notice

Prox-1635LF Socket 370

Half-size Embedded Card

With VGA / LAN

OPERATION MANUAL

COPYRIGHT NOTICE

This operation manual is meant to assist both Embedded Computer

manufacturers and end users in installing and setting up the system. The

information contained in this document is subject to change without any notice.

This manual is copyrighted January 2004. You may not reproduce or transmit in

any form or by any means, electronic, or mechanical, including photocopying

and recording.

ACKNOWLEDGEMENTS

All trademarks and registered trademarks mentioned herein are the property of

their respective owners.

CE NOTICE

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Copyright Notice

FCC NOTICE

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment not

expressly approve by the party responsible for compliance could void your

authority to operate such equipment.

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual ....................................................... 1-2

1-2 System Specification ..................................................... 1-3

1-3 Safety Precautions ......................................................... 1-6

CHAPTER 2 HARDWARE CONFIGURATION

2-1 Jumper & Connector Quick Reference Table ............... 2-2

2-2 Component Locations ................................................... 2-3

2-3 How to Set the Jumpers ................................................ 2-5

2-4 COM Port Connector ………………………………… 2-7

2-5 RS232/422/485 (COM2) Selection ............................... 2-8

2-6 PS/2 Mouse Connector …………….....................…... 2-9

2-7 Keyboard or PS/2 Mouse Selection .......................…... 2-9

2-8 External Keyboard Connector ....................................... 2-10

2-9 Reset Connector ............................................................ 2-10

2-10 ATX Power Button ………………............................... 2-10

2-11 AT/ATX Function Selection …………………………. 2-11

2-12 Hard Disk Drive LED Connector …..………………… 2-12

2-13 EXTSMI Connector …………………………………. 2-12

2-14 VGA Connector ...................................…………….... 2-13

2-15 Floppy Disk Drive Connector ...................................... 2-14

2-16 Hard Disk Drive Connector .......................................... 2-15

2-17 Printer Connector …………………………………….. 2-16

2-18 CPU Fan Connector ………………………………….. 2-17

2-19 ATX Signal Connector ……………..………………… 2-17

2-20 Wake-on-LAN Connector ……….…………………… 2-17

2-21 Universal Serial Bus Connector …………..………….. 2-18

2-22 Reset/NMI/Clear Watchdog Selection ………………. 2-19

2-23 LAN Connector …………………..…………………... 2-20

2-24 Power Connector ……………………………………. 2-20

2-25 IRDA Connector ……………………..………………. 2-21

2-26 Clear CMOS Data Selection …………………………. 2-21

2-27 Memory Installation ……………….…………………. 2-22

2-28 INTB/SERIRQ Selection …………………………….. 2-22

Contents

2-29 PPCI Connector ………………………………………. 2-23

2-30 CPU Speed Selection ………………………………… 2-24

2-31 LCD Connector ………………………………………. 2-25

2-32 Inverter Connector ……………………………………. 2-26

2-33 Power LED Connector ……………………………….. 2-26

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction …………................................................... 3-2

3-2 VIA 4 in 1 Service Pack Driver 3-2

3-3 VGA Driver Utility ………………………………….. 3-3

3-4 Flash BIOS Update ....................................................... 3-4

3-5 LAN Driver Utility …................................................... 3-6

3-6 USB2.0 Software Installation Utility ………………… 3-8

3-7 Watchdog Timer Configuration .................................... 3-9

CHAPTER 4 AWARD BIOS SETUP

4-1 Introduction ................................................................... 4-2

4-2 Entering Setup ............................................................... 4-3

4-3 The Standard CMOS Setup ………............................... 4-4

4-4 The Advanced BIOS Features ....................................... 4-8

4-5 Advanced Chipset Features ........................................... 4-11

4-6 Integrated Peripherals …............................................... 4-13

4-7 Power Management Setup ............................................ 4-18

4-8 PNP/PCI Configuration …............................................. 4-22

4-9 PC Health Status ……................................................... 4-24

4-10 Frequency/Voltage Control ........................................... 4-25

4-11 Load Fail-Safe Defaults ................................................ 4-26

4-12 Load Optimized Defaults .........................................…. 4-26

4-13 Password Setting …………………………………….. 4-27

4-14 Save & Exit Setup ......................................................... 4-28

4-15 Exit Without Saving ………………………………… 4-29

APPENDIX A EXPANSION BUS

ISA Bus Pin Assignment .......................................................... A-2

Contents

APPENDIX B TECHNICAL SUMMARY

Block Diagram ......................................................................... B-2

Interrupt Map ............................................................................ B-3

RTC & CMOS RAM Map ....................................................... B-4

Timer & DMA Channels Map .................................................. B-5

I/O & Memory Map ................................................................. B-6

APPENDIX C TROUBLE SHOOTING

Trouble Shooting for Error Messages ...................................... C-2

Trouble Shooting for POST Codes .......................................... C-8

Page:1-1

INTRODUCTION

This chapter gives you the information for Prox-1635LF. It also

outlines the System specifications.

Section includes:

z About This Manual

z System Specifications

z Safety precautions

Experienced users can skip to chapter 2 on page 2-1

for a Quick Start.

CHAPTER

1

Chapter 1 Introduction

Page: 1-2

Prox-1635LF USER

′

S MANUAL

1-1. ABOUT THIS MANUAL

Thank you for purchasing our Prox-1635LF Socket 370 Half-Size ISA CPU

Card with VGA/ LAN/CF Card, which is fully PC / AT compatible. The Prox-

1635LF provides faster processing speed, greater expandability and can

handle more tasks than before. This manual is designed to assist you how to

install and set up the system. It contains four chapters. The user can apply this

manual for configuration according to the following chapters :

Chapter 1 Introduction

This chapter introduces you to the background of this manual, and the

specifications for this system. The final page of this chapter will indicate how

to avoid damaging this Embedded Card.

Chapter 2 Hardware Configuration

This chapter outlines the component locations and their functions. In the end

of this chapter, you will learn how to set jumper and how to configure this

card to meet your own needs.

Chapter 3 Software Utilities

This chapter contains helpful information for proper installations of the VGA

Utility, LAN Utility, and Flash BIOS Update. It also describes the Watchdog-

timer configuration.

Chapter 4 Award BIOS Setup

This chapter indicates you how to set up the BIOS configurations.

Appendix A Expansion Bus

This Appendix introduces you the expansion bus for ISA BUS.

Appendix B Technical Summary

This section gives you the information about the Technical maps.

Appendix C Trouble Shooting

This section outlines the error messages and offers you the methods to solve

the problems.

Chapter 1 Introduction

Prox-1635LF USER

′

S MANUAL

Page: 1-3

1-2. SYSTEM SPECIFICATIONS

z CPU :

Intel® Celeron

TM

/ Pentium® III/ Tualatin/ C3 processors in 370-pin socket

566MHz ~ 1GHz clock generator

Auto detect voltage regulator

z MEMORY :

Up to 1GB DDR

One 184-pin DIMM socket on board

z CACHE :

Built-in CPU

z REAL-TIME CLOCK / CALENDAR :

Built-in VIA VT8235

z BIOS :

Phoenix-Award PnP, Firmware HUB BIOS memory size 4MB, with VGA

BIOS

Easy update 256KB flash EEPROM

Support Green Function.

Support S/IO Setup.

z KEYBOARD AND MOUSE CONNECTOR :

Mini DIN connector, support for keyboard or PS/2 mouse.

One additional 5-pin external keyboard connector

z BUS SUPPORT :

External PPCI Bus

z DISPLAY :

Build in VIA CLE266.

Support CRT, 24bits TTL Panel.

Onboard 15-pin CRT connector, support resolutions up to 1600 x 1200.

Onboard 41-pin connector on TTL Panel.

Chapter 1 Introduction

Page: 1-4

Prox-1635LF USER

′

S MANUAL

z WATCHDOG :

I / O port 0443H to Enable watchdog.

I / O port 0441H to Disable watchdog.

Watchdog function is selectable for Reset or NMI function.

Time-out timing select 0 / 8 / 16 / 24 / 32 / 40 / 48 / 56 / 64 / 72 / 80 / 88 / 96 /

104 / 112 / 120 sec +/- 25%.

z IDE INTERFACE :

One enhanced IDE port, support Ultra DMA-33/66/100.

One channel, support up to four devices.

z FLOPPY DISK DRIVER INTERFACE :

Support up to two Floppy Disk Drives, 3.5" and 5.25" ( 1.2M / 1.44M /

2.88M).

z USB CONNECTOR :

Universal Serial Bus Connector, support up to four USB 2.0 ports.

z LAN ADAPTER :

Single port, VIA 6103 PHY Chip

10/100 Base-TX Ethernet, support Wake-on-LAN

z CF Card Connector :

Compact Flash connector on board with second IDE, support type II CF.

z SERIAL PORT :

Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte

FIFOs;

COM1 is fixed as RS-232; COM2 selectable for RS-232/422/485.

MIDI Compatible

Programmable Baud Rate Generator

z PARALLEL PORT :

SPP, ECP, EPP Function.

Bi-directional parallel port.

z GREEN FUNCTION :

Software supported by BIOS setup.

Hardware supported by switch control.

Chapter 1 Introduction

Prox-1635LF USER

′

S MANUAL

Page: 1-5

z HARDWARE MONITORING FUNCTION :

CPUFAN

CPU Temperature

Auto Detect Voltage

z IRDA :

One Infrared port

z LED INDICATOR :

Hard Disk access

Power Indicator

z DMA CONTROLLER :

82C37 x 2

z DMA CHANNELS :

7

z INTERRUPT CONTROLLERS :

82C59 x 2

z INTERRUPT LEVELS :

15

z OPERATING TEMPERATURE :

0 to 60°C.

z INPUT POWER REQUIREMENT :

DC Voltage: +5V, minimum +4.75V, maximum 5.25V.

DC Ampere: 15A.

DC Voltage: +12V, minimum +11.4V, maximum 12.6V.

DC Ampere: 500mA.

z BOARD DIMENSIONS :

185mm x 122mm

z BOARD NET WEIGHT :

0.28 Kilograms.

Chapter 1 Introduction

Page: 1-6

Prox-1635LF USER

′

S MANUAL

1-3. SAFETY PRECAUTIONS

Follow the messages below to avoid your systems from damage:

1. Keep your system away from static electricity on all occasions.

2. Stay safe from the electric shock. Don‘t touch any components of this card

when the card is power-on. Always disconnect power when the system is

not in use.

3. Disconnect power when you change any hardware devices. For instance,

when you connect a jumper or install any cards, a surge of power may

damage the electronic components or the whole system.

Page 2-1

HARDWARE

CONFIGURATION

** QUICK START **

Helpful information describes the jumper & connector settings, and

component locations.

This section includes:

z Jumper & Connector Quick Reference Table

z Component Locations

z Configuration and Jumper settings

z Connector‘s Pin Assignments

CHAPTER

2

Chapter 2 Hardware Configuration

Page: 2-2

Prox-1635LF USER

′

S MANUAL

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

COM Connector .................................................… COM1, COM2

RS232/422/485 (COM2) Selection ........................ JP3

Keyboard or PS/2 Mouse Connector ……………. DIN1

Keyboard or PS/2 Mouse Selection ……………... JP4

External Keyboard Connector …………………… EXKB1

Reset Connector ..................................................... JP8 (1,2)

ATX Power Button ……………….…………...… JP11 (5,7)

AT/ATX Function Selection ……………………..

…………………….

JP8 (3,4), JP13,

JP9

Hard Disk Drive LED Connector .......................... JP11 (2,4,6,8)

EXTSMI Connector …………………………… JP11 (1,3)

VGA Connector ………......................................... VGA1

Floppy Disk Drive Connector ................................ FDD1

Hard Disk Drive Connector ................................... IDE1

Printer Connector ................................................... LPT1

CPU Fan Connector ............................................... FAN2

ATX Signal Connector ………………………….. JP10

Wake-On-LAN Connector ………………………. WOL1

Universal Serial Bus Connector ............................. JP5, JP6

NMI/Reset/Clear Watchdog …………………..…. JP8

LAN Connector ..................................................... UTP1

Power Connector ………………………………… PW1

IrDA Connector …………………………………. IRDA1

Clear CMOS Data Selection …………..……..….. JP1

Memory Installation ...............................................

DIMM1

INTB/SERIRQ Selection ……………………….. JP7

PPCI Connector ……………….………………… PPCI

CPU Speed Selection ……………………………. JP2

LCD Connector ………………………………….. LCD1

Inverter Connector ………………………………. JP15

Power LED Connector ………………………….. PW_LED1

Chapter 2 Hardware Configuration

Prox-1635LF USER

′

S MANUAL

Page: 2-3

2-2. COMPONENT LOCATIONS

Prox-1635LF Connector, Jumper and Component locations – Front View

Chapter 2 Hardware Configuration

Page: 2-4

Prox-1635LF USER

′

S MANUAL

Prox-1635LF Connector, Jumper and Component locations – Rear View

Chapter 2 Hardware Configuration

Prox-1635LF USER

′

S MANUAL

Page: 2-5

2-3. HOW TO SET THE JUMPERS

You can configure your board by setting the jumpers. Jumper is consists of

two or three metal pins with a plastic base mounted on the card, and by using

a small plastic "cap", Also known as the jumper cap (with a metal contact

inside), you are able to connect the pins. So you can set-up your hardware

configuration by "opening" or "closing" pins.

The jumper can be combined into sets that called jumper blocks. When the

jumpers are all in the block, you have to put them together to set up the

hardware configuration. The figure below shows how this looks like.

JUMPERS AND CAPS

If a jumper has three pins (for example, labelled PIN1, PIN2, and PIN3), You

can connect PIN1 & PIN2 to create one setting and shorting. You can either

connect PIN2 & PIN3 to create another setting. The same jumper diagrams are

applied all through this manual. The figure below shows what the manual

diagram looks like and what they represent.

Chapter 2 Hardware Configuration

Page: 2-6

Prox-1635LF USER

′

S MANUAL

JUMPER DIAGRAMS

JUMPER SETTINGS

Chapter 2 Hardware Configuration

Prox-1635LF USER

′

S MANUAL

Page: 2-7

2-4. COM PORT CONNECTOR

There are two COM port enhanced in this board namely: COM1 & COM2.

COM1 is fixed for RS-232, while COM2 is selectable for RS-232/422/485.

COM1 : COM1 Connector

The COM1 Connector assignments are as follows:

PIN ASSIGNMENT

1 DCD

2 RX

3 TX

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI

COM2 : COM2 Connector

The COM2 Connector assignments are as follows:

PIN ASSIGNMENT

RS-232 RS-422 RS-485

1 DCD TX- TX-

2 RX TX+ TX+

3 TX RX+ RX+

4 DTR RX- RX-

5 GND GND GND

6 DSR RTS- NC

7 RTS RTS+ NC

8 CTS CTS+ NC

9 RI CTS- NC

10 NC NC NC

COM1

Chapter 2 Hardware Configuration

Page: 2-8

Prox-1635LF USER

′

S MANUAL

2-5. RS232/422/485 (COM2) SELECTION

JP3 : RS-232/422/485 Selection

COM2 is selectable for RS-232, 422, 485 function.

The jumper settings are as follows :

COM 2

Function

Jumper Setting

(pin closed)

Jumper

Illustration

RS-232

Open

RS-422

1-2, 5-6, 7-8, 9-10

11-12,13-14,15-16

17-18, 19-20

RS-485

1-3, 4-6, 7-8, 9-10

11-12,13-14,15-16

17-18, 19-20

*** Manufactory default --- RS-232.

Page is loading ...

protech ProX-1635LF User manual

This manual is also suitable for

protech ProX-1635LF User manual

Related papers

Other documents