Pyle PDBC10 User manual

Category
Power supply units
Type
User manual

This manual is also suitable for

Owner's
Manual
PDBC10
-
....
-
<S;:'''l>PYLE
" 0 " " 0 0 0 " 0
PDBCID
PRO =
- -
8
Outlet
Rack
Mount
Power
Supply
Center
www.pyleaudio.com
718.535.1800
718.236.2400(fax)
1600 63rd Street, Brooklyn NY 11204
Owner's
Manual
PDBC10
-
....
-
~~~E
·
0 " " 0 " 0 " 0
~
- -
8
Outlet
Rack
Mount
Power
Supply
Center
www.pyleaudio.com
718.535.1800
718.236.2400(fax)
1600 63rd Street, Brooklyn NY 11204
OPERATION NOTICE
Thank you for buying our product. Please take a few minutes to read these
operating instructions. These instructions have important product information,
explaining the features and operation
of
your unit. Please retain these
instructions for future reference.
1.
Be sure that the line voltage
of
your
outlet
isAC
IIOV/60HZ or 220V/50HZ.
If
you aren't sure, consult your appliance
dealer or local power company.
2.
Protect the voltage line: Avoid putting pressure
on the line. Do not push or pull the line too hard.
3. Do not cover the vents: this product uses vents
to keep the temperature
of
the components
low.
Covering the vents will damage the unit.
4. Avoid water, dust, and moisture. Keep the unit
dust free and do not place liquids on or near the unit.
5.
Avoid putting the unit
in
low temperatures.
Keep the unit
in
a room where the temperature is
above
40 degrees Fahrenheit.
6.
Make sure your unit is exposed to air -- do not
operate it in a smaller container
or
near a heater.
7.
Do not drop metal in the unit. This could
cause a short-circuit and damage your
equipment.
8.
Do not open this unit. There are no
user-servicable parts inside.
Please contact
qualified personnel
if
your unit
is
not
functioning.
9.
Do not clean with volatile solutions. Do not
use alcohol, paint, or gasoline on this product.
CONTROLS AND CONNECTIONS
PLEASE
READ
THIS
MANUAL
BEFORE
OPERATING
THIS
UNIT
o
o
Caution
:To
prevent malfunctioning and/or possible equipment damage:
Before plugging the unit into the power source:
(1
) the voltage selector
switch should
be
set for the correct voltage for your area (115Vand
230V)
and (2) all equipment connected to the crossover outputs should
be
turned
off and all the inputs turned off.
NOTE:
Max power of each socket should below
200W
2 3 4 5 6 7 8
1.
Power
Switch
1
5.
Power
Switch
5
2.
Power
Switch
2
6.
Power
Switch
6
3.
Power
Switch
3
7.
Power
Switch
7
4.
Power
Switch
4 8.
Power
Switch
8
1&.&1
CE
Ef
la:
°lla
:
°lla
:
°lla
:
°lla
:
°lla
:
°lla
:
°lla
:
°1
--
2 3 4 5
1.
Power
output
socket
8
2.
Power
output
socket
7
3.
Power
output
socket
6
4.
Power
output
socket
5
5.
Power
output
socket
4
6 7 8
6.
Power
output
socket
3
7.
Power
output
socket
2
8.
Power
output
socket
1
9.
Power
Input
Cord
10. Fuse
9
o
o
10
CONTROLS AND CONNECTIONS
PLEASE
READ
THIS
MANUAL
BEFORE
OPERATING
THIS
UNIT
o
o
Caution
:To
prevent malfunctioning and/or possible equipment damage:
Before plugging the unit into the power source:
(1
) the voltage selector
switch should
be
set for the correct voltage for your area (115Vand
230V)
and (2) all equipment connected to the crossover outputs should
be
turned
off and all the inputs turned off.
NOTE:
Max power of each socket should below
200W
2 3 4 5 6 7 8
1.
Power
Switch
1
5.
Power
Switch
5
2.
Power
Switch
2
6.
Power
Switch
6
3.
Power
Switch
3
7.
Power
Switch
7
4.
Power
Switch
4 8.
Power
Switch
8
1&
.
&1
CE
Ef
la:
°lla
:
°lla
:
°lla
:
°lla
:
°lla
:
°lla
:
°lla
:
°1
--
2 3 4 5
1.
Power
output
socket
8
2.
Power
output
socket
7
3.
Power
output
socket
6
4.
Power
output
socket
5
5.
Power
output
socket
4
6 7 8
6.
Power
output
socket
3
7.
Power
output
socket
2
8.
Power
output
socket
1
9.
Power
Input
Cord
10. Fuse
9
o
o
10
  • Page 1 1
  • Page 2 2
  • Page 3 3

Pyle PDBC10 User manual

Category
Power supply units
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI