Salsbury Industries 9274GRY-U Installation guide

Storage Cabinets – 9000 Series

Assembly Instructions

Thank you for selecting Salsbury’s storage cabinets. We are confident that the quality and construction of the cabinets will prove to be a good

investment. These instructions are intended to assist you in the assembly of standard, counter height, wardrobe, and combination models.

Individual job conditions will dictate whether the storage cabinets must be anchored to the wall, the floor, or both and the type of fasteners to use to

do so.

General Notes

1. Pages 1 through 6 provide instructions for the 18” deep and 24” deep standard storage cabinets. Pages 7 through 9 provide special information

required to assemble the counter-height, wardrobe, and combination storage cabinets. For other than the standard storage cabinets, use the

standard storage cabinet instructions as a guide while referring to the pictures and special information for the other cabinets. Parts and quantities of

fasteners used will be different than for the standard cabinets.

2. Figure 9 on page 6 shows all the parts for the standard storage cabinet that should be in the package with their names as used in this document.

The parts for the counter height, wardrobe, and combination storage cabinets are shown on pages 7 through 9.

3. All the screwed connections should initially be only finger tight. Square the cabinet assembly before firmly tightening all the screwed connections.

Typical Assembly – Standard Storage Cabinet

1. Lay the Back down on a flat surface with the bottom flange up. The end with no flange and four (4) holes along the edge is the top end. See

Figure 1.

Figure 1

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

www.lockers.com engineering

@lockers.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

2. Place one of the Notch Strips along the right side of the Back with the notches inward pointed up and the Notch Strip holes aligned with the holes

along the right side of the Back. The Notch Strips are symmetrical end-to-end, so either one fits on either the right or left side of the Back.

3. Place the Right Upright along the right side of the Back with the Back and Notch Strip inside the flanges of the Upright and the top of the Upright

at the same end as the top of the Back. The rear flange on the Right Upright is the one with 7 holes. The front flange has only five (5) holes. The

top flange of the Right Upright has three (3) holes while the bottom flange has no holes. Fasten together the Back and the Notched Strip to the Right

Upright flange using seven (7) screws and nuts. Only five (5) screws and nuts go through the Notch Strip. The screws should be inserted from the

inside of the cabinet with the nuts being installed on the rear of the cabinet.

4. Repeat 2 and 3 with the Left Upright and other Notch Strip using another seven (7) screws and nuts.

5. Stand the Uprights and Back assembly up. Insert the Top from the rear of the cabinet underneath the top flanges of the Right and Left Uprights.

The only flange of the Top should be in the rear and pointing downward toward the bottom of the cabinet. The flange of the

Top will be on the outside of the back. Attach the Top to the Upright flanges and Back using ten (10) screws and nuts, three (3) on each side on the

top and four (4) in the rear. See Figure 2.

Figure 2

6. Place the Bottom between the Uprights and fasten to the Uprights and the Back using ten (10) screws and nuts, three (3) on each side and four

(4) in the rear. See Figure 3.

Figure 3

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

7. Place Door Frame Assembly upon the Uprights with the top of the Frame fitting over the Top panel. Fasten Door Frame Assembly to the Uprights

using seven (7) screws and nuts on each side hidden inside the flanges. Fasten the front edge of the Top panel to the top of the Door Frame

Assembly using four (4) screws and nuts. See Figure 4.

Figure 4

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

8. Fasten Right Door with holes for Handle and lock to hinges on right side of Frame. Attach using two (2) screws and nuts per each of the three (3)

hinges. Repeat to fasten Left Door to hinges on left side of Frame. For this step it may be more convenient to stand the cabinet assembly up

vertically. However, the illustrations show the cabinet remaining in the beginning position. See Figure 5.

Figure 5

9. Mount Handle on Right Door with two (2) screws and lockwashers. Insert Lock Bar Guides into slots on top and bottom of Right Door. Ensure

that Guides are fully inserted and locked in place. See Figure 6.

Figure 6

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

10. Rotate latch to position shown below. Mount Lock Bars on Latch as shown below. Do not fasten Latch to Handle yet. Rotate Handle to open

(unlatched position or horizontal) position. Insert Lock Bars into plastic Guides while aligning square hole in Latch with square threaded shoulder on

Handle. Install lock nut on threaded shank of Handle. Check that Handle, Latch, and Lock Bars operate smoothly and effectively. See Figure 7.

Figure 7

11. Open the Doors. The Shelves fit into notches in the Notched Strips on the back wall of the cabinet. Fasten the Shelves with two (2) screws and

nuts, one (1) in each of the two (2) front corners of each Shelf. Locate the Shelves as dictated for the cabinet’s ultimate use. The Shelves are

adjustable on 2” centers. See Figure 8.

Figure 8

This completes the assembly of your storage cabinet.

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Figure 9 - Standard Storage Cabinet – Parts Identification and Count

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Assembly Special Information – Counter Height Cabinet

The parts for the counter height storage cabinet are much shorter in vertical height than the standard storage cabinet. The only parts that are the

same as in the standard cabinet are the handle, latch, lock bar guides, shelf, and bottom. The Top sits on top of the flanges of the Back and the

Right and Left Uprights and the seven (7) screws and nuts to attach the top are hidden inside the flanges of the Top. The counter height cabinet has

only one (1) shelf and it may be installed in any desired position. Fewer fasteners are required to assemble the counter height cabinet due to the

shorter height. See the illustration below while generally following the instructions for the standard storage cabinet.

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Assembly Special Information – Wardrobe Cabinet

1. Assemble the Back, Notch Strips, Right and Left Uprights, Top, and Bottom in that same manner as in the standard cabinet.

2. Assemble the two (2) Rod Hangers to the outside of the centers of the side flanges of the Top Shelf. Each Rod Hanger is fastened with two (2)

screws and nuts. Install the Coat Rod into the hangers before fastening the second hanger. See illustration below.

3. Assemble the Door Frame Assembly to the Right and Left Uprights and Top in the same manner as in the standard cabinet.

4. Assemble the Top Shelf with installed Coat Rod into the cabinet in the same manner as installing a Shelf into the standard cabinet.

5. The Doors, Handle, Latch, and Lock Bars are assembled in the same manner as in the standard cabinet.

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Assembly Special Instructions – Combination Cabinet

1. Assemble the Back, Notch Strips, Right and Left Uprights, Top, and Bottom in that same manner as in the standard cabinet.

2. Assemble the two (2) Rod Hangers to the outside of the centers of the side flanges of the Top Shelf. Each Rod Hanger is fastened with two (2)

screws and nuts. Install the Coat Rod into the hangers before fastening the second hanger. See illustration below.

3. Assemble the Door Frame Assembly to the Right and Left Uprights and Top in the same manner as in the standard cabinet.

4. Assemble the Top Shelf with installed Coat Rod into the cabinet in the same manner as installing a Shelf into the standard cabinet.

5. The combination cabinet has a Center Partition that installs between the Top Shelf and the Bottom and is fastened to these items with two (2)

screws to the Top Shelf and three (3) screws to the Bottom.

6. The four (4) Small Shelves are installed between the Left Upright and the Center Partition with three (3) screws each. The left side of each shelf

installs in the same manner as in the standard cabinet, i.e. into the Notch Strip in the left rear corner with one (1) screw and nut fastening the front

left corner. The right flange of each Small Shelf fastens to the Center Partition with two (2) screws and nuts. The Small Shelves may be installed in

any vertical position at 2” increments.

7. The Doors, Handle, Latch, and Lock Bars are assembled in the same manner as in the standard cabinet.

SALSBURY INDUSTRIES

1010 East 62

nd

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Salsbury Industries 9274GRY-U Installation guide

Salsbury Industries 9274GRY-U Installation guide

Related papers

Other documents