Edsal 1UFF1 to 1UFF5 Assembly Manual

Brand: Edsal

Model: 1UFF1 to 1UFF5

Type: Assembly Manual

This manual is also suitable for

1UFE9

Models: 1UFE9, 1UFF1, 1UFF2, 1UFF3, 1UFF4, 1UFF5

Use Caution when handling and assembling metal parts. The metal may have sharp edges or corners. The use of pro-

tective gloves is recommended. Do not use this unit for anything that is outside the designed function of storage. Do

not store loose or heavy items on the top shelves or on the top of the unit, for they create a falling hazard that can injure

yourself or others. Always remember to use proper lifting techniques when moving either the boxed or assembled unit.

Cabinet Instruction Manual

Part List & Product Specification (patent pending)

Safety Instructions

It is recommended that the cabinets are assembled by more than one person. Use of a raised flat surface during assembly is highly

recommended. During shipping and handling, some of the panels that are used for assembly may have become bent. Use your hand

to pry up or push the parts back to their original form. To assure the unit is square, do not fully tighten the nuts and screws used in

the assembly until all are in place. After all nuts and screws are in place, square the unit and tighten all nuts and screws appropri-

ately. Make sure that the unit is placed on a level surface, as this may effect the performance of the unit.

General instructions

Reference

Page 1

(F) Bottom (G) Shelves

Right Hand Back

Left Hand Back

Right Hand Side

Left Hand Side

Top

Bottom

Shelves

Shelf Clips

Right Hand Door

Left Hand Door

Door Rods

10-24X3/8” Screws

Locking Handle

Description

CRBK7918R

CRBK7918L

CRSD7921-SR

CRSD7921-SL

CRTO3612-S

CRBO3624-S

CRSH3719

7000CLP

CRDO7318R

CRDO7318L

Offset Rod 36

102438S & N

RLHAB Recessed Handle

1UFE9, 1UFF1

4 Shelf

–

78”h x 18”d x 36”w

CRBK7918R

CRBK7918L

CRSD7927-SR

CRSD7927-SL

CRTO3627-S

CRBO3630-S

CRSH3725

7000CLP

CRDO7318R

CRDO7318L

Offset Rod 36

F102438S & N

RLHAB Recessed Handle

1UFF2, 1UFF3

4 Shelf

–

78”h x 24”d x 36”w

Required Tools

- Socket or Nut Driver

- Small Screwdriver

(I) Right Hand Door

(J) Left Hand Door

(K) Door Rods

(H) Shelf Clips

(L) 10-24 x 3/8”

Screws & Nuts

(M) Locking Handle

(A) Right Hand

(B) Left Hand Back

(E) Top

CRBK7924R

CRBK7924L

CRSD7927-SR

CRSD7927-SL

CRTO4827-S

CRBO4830-S

CRSH4925

7000CLP

CRDO7324R

CRDO7324L

Offset Rod 36

F102438S & N

RLHAB Recessed Handle

1UFF4, 1UFF5

4 Shelf

–

78”h x 24”d x 48”w

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal Manufacturing

facility at (773) 475-3000 and request customer service. We can also be reached on the internet at the following e-mail address:

[email protected]

To obtain replacement parts, please provide the following information :

- Model # - Part # & Description - Location Purchased - Date Purchased

This instruction sheet was designed to help you assemble this unit in the proper way, please follow them using all

parts and fasteners provided. Any alteration or deviation from this instruction sheet can result in unit failure. If

you have any assembly problems or questions, please feel free to contact our Alera Manufacturing facility at 1-

800-336-0671 and ask for customer service. We have people available to assist you if need be with any part of

this assembly process.

IT IS HIGHLY RECOMMENDED TO ASSEMBLE THIS UNIT AT EYE LEVEL, AND WITH THE HELP OF AN

ADDITIONAL PERSON. Using a RAISED surface such as a TABLE or DESK, will greatly EASE the ASSEMBLY

PROCESS. Assembly attempted on a much lower surface such as the floor, is still possible but does make the

assembly process longer and harder. During the shipping and handling of this product, some of the panels may

have a MINOR bend such as on a corner, or a door hinge pin. This minor variation can be REPAIRED SIMPLY

by using a SMALL TOOL or your HAND to move the material back to its designed form. Some of the materials

used in the packaging to protect the parts from damage may leave dust or smudges on the steel panels. It is

RECOMMENDED AFTER ASSEMBLY IS COMPLETE to use a MILD SOAP and WATER with a SOFT CLOTH

to wipe the unit clean.

Assembly Instructions

Page 2

Important Please Read First

This assembly process uses screws, and nuts to hold the parts together. To speed the assembly proc-

ess, have the necessary nut driver or socket wrench, and a screwdriver ready. Also have your pack-

aged hardware at close reach. After unpacking all the panels, visually inspect the corners. These are

the most susceptible to damage through the shipping and handling process. If you find a corner bent or

out of place, use your hand and gently move the corner back to the designed shape.

Getting Started

Step 1 - Back Assembly

Place the left and right hand backs on a level surface.

Position the parts so that the offsets over lap (see figure

1 for reference). Check that the screw holes on the back

panels have properly aligned. Use your small tipped

screwdriver to assist in aligning the screw holes if neces-

sary. Using the 10-24 x 3/8” screws and nuts provided,

bolt the backs together to complete the back assembly

(see figure 1 for reference).

Figure 1 – Back Assembly

Backs Overlap

Screw locations

Left Hand Back

Right Hand Back

Unit Top

Unit Bottom

Assembly Instructions

Page 3

Step 2 - Sides & Top Assembly

First step is to identify the right side panel and the left

side panel. After you have determined the left from the

right panel, place the left side panel with the hinges fac-

ing up toward you under the back assembly making sure

the holes of the side panel flange align with the holes of

the back assembly. After assuring the correct side is

aligned to the back assembly, use the 10-24 x 3/8”

screws and nuts to fasten the side panel to the back as-

sembly. Next take the top and place it into position un-

der the top flanges of the back assembly and the left

hand side panel. Using four (4) 10-24 x 3/8” screws and

nuts for fastening the back of the top, and two (2) 10-24

x 3/8” screws and nuts for fastening the front of the top,

align the screw holes of the top with the screw holes

from the left hand side top flange, and the back assem-

bly top flanges and fasten appropriately (see figure 2 for

screw locations). Now install the right side panel using

the same process as outlined above.

Figure 2 - Sides & Top Assembly

Step 3 - Bottom Assembly

The back, side, and top assembly is ready for the bot-

tom. Holding the bottom from the largest formed side

(front), place the bottom onto the inside of the back, side,

and top assembly. The rear flange of the bottom will

align with the screw holes on the back assembly, and the

sides of the bottom will engage into slots located on the

left and right hand side panels (see figure 3 for refer-

ence). Once all tabs have been properly engaged, and

all the screw holes align, move the front of the bottom

into position so that the screw holes align with the front

of the left and right side panels (use a small tipped screw

driver to assist in aligning the holes if necessary). Using

four (4) of the 10-24 x 3/8” screws and nuts, attach the

back flange of the bottom to the back assembly, and us-

ing four (4) of the 10-24 3/8” screws and nuts attach the

front of the bottom to the side panels (see figure 3 for

screw locations).

Figure 3 - Bottom Assembly

Figure 3 - Top Assem-

Screw Locations

for Top to Side

Screw Locations

for Side to Back

Screw Locations for Back to Top

Left Side

Right Side

Top

Screw Locations

For bottom to sides

(opposite side also)

Screw Locations

For bottom to sides

(opposite side also)

Screw Locations

For bottom to back

Tab Location

For bottom to sides

(opposite side also)

Bottom

Assembly Instructions

Page 4

Step 5 - Shelf Assembly

The unit is now ready for the shelves. Holding the shelf,

notice there are square and round cutouts on the edge of

the part. The square cutouts will install to the back of the

unit, and the round to the front. First select a level for

the shelf by selecting a set of square notches located

inside the unit on the back left and back right sides. A

series of round holes are located on the inside of the left

and right hand side panels near the hinges. Using a

shelf clip, insert the upper notch into a round hole oppo-

site the selected square holes where the shelf is to be

located. Push and “snap” the lower notch of the clip into

place using the next lowest round hole. Repeat the shelf

clip installation on the opposite corresponding side. To

insert the shelf, place the end with the square cutout to

the rear of the unit. Angle the shelf so that the shelf will

engage the square notches on the back assembly and

lower onto the front shelf clips. Repeat the process for

all remaining shelves. DO NOT install shelves in the

area even with the door handle. This will affect per-

formance of the cabinet by causing interference with

Figure 5 - Shelf Assembly

Step 6 - Final Assembly

To complete the unit, the locking handle needs to be in-

stalled on the right hand door. Follow carefully the as-

sembly instructions as written on the handle hardware

bag. Helpful hints on installation: The door rods will

slide into small plastic guides on the door. Install the

handle to the right hand door, then place the cam in posi-

tion. Slide the tip of the door rod into the lower plastic

guide and position the door rod onto the pin located on

the cam and hold it in place. Install the other door rod in

the upper plastic guide and position onto pin located on

the cam. Install the remaining hardware.

Figure 6 - Final Assembly

Figure 4 - Door Assembly

Step 4 - Door Assembly

First the unit needs to be squared. Turn the unit upright

and place on a level floor. Loosen and re-tighten the

screws appropriately to ensure the unit is square. Now

the doors are ready to be hung. With the hinge pins

pointed down, select the door with the handle hole (see

figure 4 for assistance). This is the right hand door.

Take the right hand door and align the door’s hinge pins

with the companion hinges located on the right side

panel. Some of the hinge pins may have moved or come

out of alignment during shipping and handling. If so,

move the hinge pins back to the proper position so that

they align with the companion hinge holes. Slowly slide

the hinge pins into the holes to properly seat the door.

Repeat the same process for the left hand door.

Edsal 1UFF1 to 1UFF5 Assembly Manual

Brand: Edsal

Model: 1UFF1 to 1UFF5

Type: Assembly Manual

This manual is also suitable for

1UFE9

Download PDF

report

Edsal 1UFF1 to 1UFF5 Assembly Manual

This manual is also suitable for

Edsal 1UFF1 to 1UFF5 Assembly Manual

Related papers

Other documents