RLM W6 adapter plate
Quick Installation Guide
R59770765 Rev. 00, January 2014
1
Barco nv
Noordlaan 5, B-8520 Kuurne
www.barco.com
Mounting the adapter plate on adjustable frame
1. Loosen the three hexagonal screws on the adapter
plate.
2. Position the adapter plate as illustrated; align the hex-
agonal screws of the adapter plate with the notches of
the adjustable frame.
3. Mount the adpater plate on the adjustable frame by
doing following:
• slide in (F) the adapter plate until its hexagonal
screws are fully inside their respective notch (N)
on the adjustabe frame;
• secure the adapter plate by sliding it sideward (S).
4. Tighten the three hexagonal screws to fix the adpater
plate on the adjustable frame.
Steps
Tools
Open ended wrench 12 mm
Parts
• R3623995 - Hexagonal screw (A);
• R9849600 - Adapter plate (B);
• R850600 - Adjustable frame (C).
A
A
A
Step 1
B
C
Step 2
Step 3
Step 4
A
A
A
F
S
A
N
RLM W6 adapter plate
Quick Installation Guide
R59770765 Rev. 00, January 2014
2
Preparing the projector
Tools
Open ended wrench 8 mm
Parts
• R9006300 - RLM W6 projector (A);
• R819602 - Bolt (3x) (B);
• Lock nut (3x) (C);
• B360623 - Flange nut (3x) (D).
Steps
1. Turn the projector upside down.
2. Screw in the three bolts into the holes on the projector.
3. Tighten the hexagonal lock nut on each bolt in turn to
fix the bolts into the projector.
4. Screw in a flange nut to an equal height on each bolt.
Step 1
A
Step 3
C
Step 2
D
Step 4
B
RLM W6 adapter plate
Quick Installation Guide
R59770765 Rev. 00, January 2014
3
Mounting the projector
Tools
Open ended wrench 8 mm
Parts
• R9006300 - RLM W6 projector (A);
• R819602 - Bolt (3x) (B);
• R9849600 - Adapter plate (C);
• R850600 - Adjustable frame (D);
• B360623 - Flange nuts (3x) (E);
• R366245 - Hexagonal lock nuts (3x) (F).
Steps
1. Fit the bolts at the bottom of the projector into to the
holes in the adapter plate (1a) until the flange nuts
touch the adapter plate (1b).
2. Screw a flange nut on each of these bolts to fix the pro-
jector to the adapter plate.
Note: Changing the position of both flange nuts on the bolts
changes the projector distance to the adapter plate
(i.e. height adjustment).
3. Secure the position of the nuts on each of the bolts by
adding and tightening a hexagonal nut.
Step 1a
A
B
B
B
C
D
Step 1b
E
Step 2
E
Step 3
F
RLM W6 adapter plate
Quick Installation Guide
R59770765 Rev. 00, January 2014
4
Projector alignments
Yaw adjustmentPitch adjustment
T
T
T
T
10°
A
• Rotate the threaded rod (T) counterclockwise/clockwise - to lift/lower
the rear end of the projector respectively and correct the vertical keystone.
• Rotate the threaded rod (T) counterclockwise/clockwise - to rotate the pro-
jector left/right respectively around the vertical axis (A) in a horizontal plane
and correct the horizontal keystone.
RLM W6 adapter plate
Quick Installation Guide
R59770765 Rev. 00, January 2014
5
Roll adjustment Translation adjustment
T
T
T
T
• Rotate the threaded rod (T) counterclockwise/clockwise - to tilt the
projector up/down and rotate the projected image clockwise/counter-
clockwise respectively.
• Rotate the threaded rod (T) counterclockwise/clockwise - to move the
projector forward/backward and zoom in/zoom out the projected image
respectively.
Projector alignments
RLM W6 adapter plate
Quick Installation Guide
R59770765 Rev. 00, January 2014
6
Lateral adjustment
T
T
• Rotate the threaded rod (T) counterclockwise/clockwise - to move the
projector left/right and shift left/shift right the projected image respec-
tively.
Projector alignments
-
1
-
2
-
3
-
4
-
5
-
6
Barco RLM-W6 Quick start guide
- Category
- Projector mounts
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco F22 series Quick start guide
-
-
Barco Projector Toolset User guide
-
-
Barco RLM-W8 Owner's manual
-
Barco RLM R6+ Performer User manual
-
Barco RLM-W14 User guide
-
-
-