Brother Innov-is 780D Owner's manual

PANTONE 285 Black Fcombo_emb_cover

Computerized Embroidery Machine

Operation Manual

GETTING READY

EMBROIDERY

APPENDIX

English

882-U30

XD1628-051

Printed in Taiwan

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

IMPORTANT SAFETY INSTRUCTIONS

Please read these safety instructions before attempting to use the machine.

DANGER - To reduce the risk of electric shock

1Always unplug the machine from the electrical outlet immediately after using, when cleaning,

when making any user servicing adjustments mentioned in this manual, or if you are leaving the

machine unattended.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons.

2Always unplug the machine from the electrical outlet when removing covers, lubricating, or

when making any adjustments mentioned in the instruction manual.

• To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp

the plug and pull it out of the electrical outlet. Do not pull on the cord.

• Plug the machine directly into the electrical outlet. Do not use an extension cord.

• Always unplug your machine if the power is cut.

3 Never operate this machine if it has a damaged cord or plug, if it is not working properly, if it has

been dropped or damaged, or water is spilled on the unit. Return the machine to the nearest

authorized dealer or service center for examination, repair, electrical or mechanical adjustment.

4 Always keep your work area clear:

• Never operate the machine with any air openings blocked. Keep ventilation openings of the

machine free from the build up of lint, dust, and loose cloth.

• Do not use extension cords. Plug the machine directly into the electrical outlet.

• Never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

5 Special care is required when embroidering:

• Always pay close attention to the needle. Do not use bent or damaged needles.

• Keep fingers away from all moving parts. Special care is required around the machine needle.

• Switch the machine to the symbol “O” position to turn it off when making any adjustments in the

needle area.

• Do not use a damaged or incorrect needle plate, as it could cause the needle to break.

• Do not push or pull the fabric when embroidering.

1

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

6 This machine is not a toy:

• Your close attention is necessary when the machine is used by or near children.

• Do not use outdoors.

7 For a longer service life:

• When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store

the machine near a space heater, iron, halogen lamp, or other hot objects.

• Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders

can damage the case and machine, and should never be used.

• Always consult the operation manual when replacing or installing any assemblies, the presser feet,

needle, or other parts to assure correct installation.

8 For repair or adjustment:

• If the Light unit is damaged, it must be replaced by authorized dealer.

• In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table

in the back of the operation manual to inspect and adjust the machine yourself. If the problem

persists, please consult your local authorized Brother dealer.

Use this machine only for its intended use as described in the manual.

Use accessories recommended by the manufacturer as contained in this manual.

The contents of this manual and specifications of this product are subject to change without notice.

For additional product information and updates, visit our web site at www.brother.com

SAVE THESE INSTRUCTIONS

This machine is intended for household use.

2

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

FOR USERS IN THE UK, EIRE, MALTA AND

CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the

mark, rating as marked on plug.

• Always replace the fuse cover. Never use plugs with the fuse cover omitted.

• If the available electrical outlet is not suitable for the plug supplied with this equipment, you

should contact your authorized dealer to obtain the correct lead.

FOR USERS IN AC INPUT 220-240V

COUNTRIES AND MEXICO

This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

3

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Contents

Introduction ........................................................................................................................5

Machine Features ................................................................................................................5

Accessories..........................................................................................................................6

Included accessories .........................................................................................................................................6

Optional accessories .........................................................................................................................................7

Names of Machine Parts and Their Functions .....................................................................8

Front view.........................................................................................................................................................8

Needle and embroidery foot section .................................................................................................................9

Right-side/rear view ..........................................................................................................................................9

Operation buttons...........................................................................................................................................10

Operation panel..............................................................................................................................................11

GETTING READY 13

Embroidery Step by Step ...................................................................................................14

Attaching the Embroidery Unit..........................................................................................15

Embroidery unit precautions ........................................................................................................................... 15

Attaching the embroidery unit......................................................................................................................... 15

Removing the embroidery unit ........................................................................................................................16

Turning the Machine On/Off.............................................................................................18

Power supply precautions ...............................................................................................................................18

Turning on the machine ..................................................................................................................................19

Turning off the machine ..................................................................................................................................19

LCD (Liquid Crystal Display) Operation............................................................................20

Viewing the LCD.............................................................................................................................................20

Changing the machine settings........................................................................................................................21

Checking machine operating procedures ........................................................................................................23

Winding/Installing the Bobbin...........................................................................................24

Bobbin precautions .........................................................................................................................................24

Winding the bobbin ........................................................................................................................................24

Installing the bobbin .......................................................................................................................................28

Upper Threading ...............................................................................................................30

About the spool of thread ................................................................................................................................30

Threading the upper thread .............................................................................................................................30

Threading the needle ...................................................................................................................................... 32

Threading the needle manually (without using the needle threader) ................................................................34

Replacing the Needle ........................................................................................................35

Needle precautions.........................................................................................................................................35

Checking the needle .......................................................................................................................................35

Replacing the needle.......................................................................................................................................36

EMBROIDERY 39

Embroidering Neatly .........................................................................................................40

What to prepare ..............................................................................................................................................40

Preparing the Fabric ..........................................................................................................42

Attaching a stabilizer material to the fabric ..................................................................................................... 42

Setting the fabric in the embroidery frame.......................................................................................................43

Attaching the Embroidery Frame.......................................................................................47

Attaching the embroidery frame ...................................................................................................................... 47

Removing the embroidery frame ..................................................................................................................... 48

Selecting Embroidery Patterns...........................................................................................49

Copyright information .................................................................................................................................... 49

Embroidery pattern types.................................................................................................................................49

LCD (liquid crystal display) operation .............................................................................................................50

Selecting characters ........................................................................................................................................52

Selecting an embroidery pattern......................................................................................................................53

Selecting a frame pattern.................................................................................................................................54

4

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Using an embroidery card (sold separately) ....................................................................................................55

Embroidering.....................................................................................................................56

Embroidering attractive finishes.......................................................................................................................56

Embroidering a pattern.................................................................................................................................... 57

Appliquéing ...................................................................................................................................................59

Editing and Saving Patterns ...............................................................................................61

Adjusting the layout ........................................................................................................................................61

Storing patterns ...............................................................................................................................................63

Adjusting the thread tension............................................................................................................................ 64

Resewing ........................................................................................................................................................65

Thread runs out partway through a design.......................................................................................................65

Stopping while embroidering ..........................................................................................................................66

Bobbin Case Adjustment ...................................................................................................68

Correct tension................................................................................................................................................68

Bobbin thread is loose.....................................................................................................................................68

Bobbin thread is tight ......................................................................................................................................68

APPENDIX 69

Care and Maintenance ......................................................................................................70

Cleaning the machine surface .........................................................................................................................70

Cleaning the race............................................................................................................................................70

Attaching the Embroidery Foot..........................................................................................72

Attaching the embroidery Foot “Q”................................................................................................................. 72

Troubleshooting ................................................................................................................74

Error messages ................................................................................................................................................78

Adjusting the LCD...........................................................................................................................................81

Operation beep...............................................................................................................................................81

Canceling the operation beep .........................................................................................................................82

Index .................................................................................................................................83

5

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Introduction

Thank you for purchasing this embroidery machine. Before using the machine, carefully read the

“IMPORTANT SAFETY INSTRUCTIONS”, and then study this manual for the correct operation of the

various functions. In addition, after you have finished reading this manual, store it where it can quickly be

accessed for future reference.

Machine Features

a Simple bobbin-winding

The bobbin can quickly and easily be wound with thread (page 24).

b Quick-set bobbin

You can start embroiderying without pulling up the bobbin thread (page 28).

c Automatic thread cutting

The thread can be cut automatically after embroidering (page 51).

d Embroidery

You can embroider built-in embroidery patterns, characters, framed decorations, and designs from optional embroidery

cards (page 39).

32

1

4

6

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Accessories

Included accessories

After opening the box, check that the following accessories are included. If any item is missing or damaged,

contact your retailer.

1. 2. 3.* 4. 5. 6. 7. 8. 9.

10. 11. 12. 13. 14. 15.

16. 17.

*75/11 3 needles

90/14 1 needle

No. Part Name

Part Code

No. Part Name

Part Code

U.S.A. / Canada

Others

U.S.A. / Canada

Others

1 Seam ripper X54243-051 10 Spool net XA5523-020

2 Bobbin (4) SA156

SFB:

XA5539-

151

11 Operation manual XD1628-121

12 Quick reference guide XD1629-021

13

Embroidery foot “Q”

(on machine)

XD0474-151

3 Needle set X59535-051

4 Cleaning brush X59476-021

14

Embroidery set (large)

H 18cm X W 13 cm

(H 7 inches X W 5 inches)

SA444/EF84

EF84:

XD0600-

002

5 Screwdriver (large) XC8349-021

6 Screwdriver (small) X55468-051

7 Spool cap (large) 130012-024 15 Scissors XC1807-121

8 Spool cap (medium) XE1372-001 16 Dust cover XZ5004-021

9 Spool cap (small) 130013-124 17 Accessory bag XC4487-021

7

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Optional accessories

The following are available as optional accessories.

Memo

z To obtain optional accessories or parts, contact your sales representative or the nearest authorized

service center.

z

All specifications are correct at the time of printing. The part codes are subject to change without notice.

z Visit your nearest authorized retailer for a complete listing of optional accessories available for your

machine.

1. 2. 3. 4.

5.

6.

No. Part Name

Part Code

No. Part Name

Part Code

U.S.A. / Canada

Other

U.S.A. / Canada

Other

1

Brother poly #90

bobbin thread

EBT-PE

EBT-PEN:

XC5996-001 5

Embroidery set (medium)

H 10 cm X W 10 cm

(H 4 inches X W 4 inches)

SA443/

EF83

EF83:

XD0599-002

2

Water solude stabilizer SA520

BM4: X81267-001

EBT-CEN

6

Embroidery set (extra large

(multi-position))

H 30 cm X W 13 cm

(H 12 inches X W 5 inches)

SA445

EF85:

XD0601-002

Stabilizer material for

embroidery

SA519

BM3: X81175-001

EBT-CEN

3 Embroidery card

–

4

Embroidery set (small)

H 2 cm X W 6 cm

(H 1 inch X W 2-1/2

inches)

SA442/

EF82

EF82:

XD0598-002

8

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Names of Machine Parts and Their Functions

The names of the various parts of the machine and their functions are described below. Before using the

machine, carefully read these descriptions to learn the names of the machine parts.

Front view

a Thread guide plate

Pass the thread around the thread guide plate when

threading the upper thread.

b Thread guide cover

Like with the thread guide plate, pass the thread around

the thread guide cover when threading the upper

thread.

c Spool pin

Place a spool of thread on the spool pin.

d Bobbin winding thread guide

Pass the thread around this thread guide when winding

the bobbin thread.

e Top cover

Open the top cover to place the spool of thread on the

spool pin.

f Bobbin winder

Use the bobbin winder when winding the bobbin.

g Operation panel

From the operation panel, patterns can be selected and

edited, and operations for using the machine can be

displayed (page 11).

h Embroidery unit connector slot

Plug in the connector for the embroidery unit.

i Presser foot lever

Raise and lower the presser foot lever to raise and lower

the presser foot

j Operation buttons

Use these buttons to operate the machine.

k Embroidery unit

Attach the embroidery unit to the machine, and then

attach the embroidery frame.

l Thread cutter

Pass the threads through the thread cutter to cut them.

m Needle threader lever

Use the needle threader lever to thread the needle.

n Thread take-up lever check window

Look through the window to check the position of the

take-up lever.

9

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Needle and embroidery foot section

a Thread guide disk

Pass the thread through the thread guide disk when

using the needle threader to thread the needle.

b Needle bar thread guide

Pass the upper thread through the needle bar thread

guide.

c Needle plate

When the needle is lowered, it enters the hole in the

needle plate.

d Needle plate cover

Remove the needle plate cover to clean the bobbin case

and race.

e Bobbin cover/bobbin case

Remove the bobbin cover, and then insert the bobbin

into the bobbin case.

f Embroidery foot “Q”

This presser foot is used for embroidering.

Right-side/rear view

a Handle

Carry the machine by its handle when transporting the

machine.

b Handwheel

Turn the handwheel toward you (counterclockwise) to

raise and lower the needle.

c Embroidery card slot

Insert the embroidery card.

d Air vent

The air vent allows the air surrounding the motor to be

exchanged. Do not cover the air vent while the

machine is being used.

e Power supply jack

Insert the plug on the power supply cord into the power

supply jack.

f Main power switch

Use the main power switch to turn the machine on and

off.

Memo

z Refer to pages 8 through 11 while you are

learning to use your machine.

10

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Operation buttons

The operation buttons help you to easily perform various basic machine operations.

a Start/stop button

Press the start/stop button to start or stop embroidering.

The machine embroiders at a slow speed while the

button is pressed. When embroidering is stopped, the

needle is lowered in the fabric.

The button changes color according to the machine’s

operation mode.

b Needle position button

Press the needle position button to raise or lower the

needle. Pressing the button twice sews one stitch.

c Thread cutter button

Press the thread cutter button after embroidering is

stopped to cut both the upper and the bobbin threads.

CAUTION

Note

z Do not press the thread cutter button if there

is no fabric under the presser foot or while

the machine is embroidering, otherwise

damage to the machine may occur.

z When cutting thread thicker than #30, nylon

thread or other special threads, use the

thread cutter on the side of the machine.

Green: The machine is ready to embroider or

is embroidering.

Red: The machine can not embroider.

Orange: The machine is winding the bobbin

thread, or the bobbin winder shaft is

moved to the right side.

● Do not press the thread cutter button

after the threads have already been cut,

otherwise the needle may break, the

threads may become tangled or damage

to the machine may occur.

11

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Operation panel

The front operation panel has an LCD (liquid crystal display) and operation keys.

a LCD (liquid crystal display) (touch panel)

Touch the keys displayed on the LCD to perform

operations.

For details, refer to “LCD (Liquid Crystal Display)

Operation” (page 20).

b Back key

Press to return to the previous screen.

c Previous page key

Press to display the previous screen when there are

items that are not displayed on the LCD.

d Next page key

Press to display the next screen when there are items

that are not displayed on the LCD.

e Memory key

Press to store patterns in the machine's memory.

f Embroidery key

Press to display the pattern type selection screen.

g Settings key

Press to display the settings screen.

h Help key

Press to get help on using the machine.

Displays simple explanations of setting upper thread /

bobbin winding / setting bobbin thread / embroidery

unit attachment / embroidery frame attachment / needle

replacement.

a

c

b

fg

d

e

h

12

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

1 GETTING READY

The various preparations to start embroidering are described in this chapter.

Embroidery Step by Step .........................................................................................14

Attaching the Embroidery Unit................................................................................15

Embroidery unit precautions ..............................................................................15

Attaching the embroidery unit ...........................................................................15

Removing the embroidery unit...........................................................................16

Turning the Machine On/Off ..................................................................................18

Power supply precautions ..................................................................................18

Turning on the machine .....................................................................................19

Turning off the machine .....................................................................................19

LCD (Liquid Crystal Display) Operation..................................................................20

Viewing the LCD ................................................................................................20

Changing the machine settings...........................................................................21

Checking machine operating procedures ...........................................................23

Winding/Installing the Bobbin.................................................................................24

Bobbin precautions ............................................................................................24

Winding the bobbin ...........................................................................................24

Installing the bobbin ..........................................................................................28

Upper Threading .....................................................................................................30

About the spool of thread ..................................................................................30

Threading the upper thread................................................................................30

Threading the needle..........................................................................................32

Threading the needle manually (without using the needle threader)..................34

Replacing the Needle ..............................................................................................35

Needle precautions ............................................................................................35

Checking the needle...........................................................................................35

Replacing the needle ..........................................................................................36

GETTING READY — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

14

Embroidery Step by Step

The basic steps for embroidery are as follows.

↓

1

Attaching the embroidery

unit

Attach the embroidery unit. (If the embroidery unit is not attached, the

machine does not operate.)

For details, refer to “Attaching the embroidery unit” (page 15).

2 Checking the needle

Use a needle matched to the fabric.

For details on replacing the needle, refer to “Replacing the needle” (page

36).

3

Setting up the bobbin

thread

For the bobbin thread, wind embroidery bobbin thread and set it in

place.

For details, refer to “Winding/Installing the Bobbin” (page 24).

4 Preparing the fabric

Attach a stabilizer material to the fabric, and hoop it in an embroidery

frame.

For details, refer to “Preparing the Fabric” (page 42).

5

Attaching the embroidery

frame

Attach the embroidery frame to the embroidery unit.

For details, refer to “Attaching the Embroidery Frame” (page 47).

6 Selecting a pattern

Select an embroidery pattern.

For details, refer to “Selecting Embroidery Patterns” (page 49).

7 Checking the layout

Check and adjust the size and position of the embroidery pattern.

For details on adjusting the layout, refer to “Adjusting the layout” (page

61).

8

Setting up the embroidery

thread

Set up the embroidery thread according to the pattern.

For details, refer to “Upper Threading” (page 30).

Attaching the Embroidery Unit 15

1

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Attaching the Embroidery Unit

This section describes how to attach the embroidery unit. Before turning on the machine, attach the

embroidery unit to it. If the embroidery unit is not attached, the machine does not operate.

Embroidery unit precautions

Cautions for the embroidery unit will be explained

below.

CAUTION

Note

z Do not touch the connector in the

embroidery unit connector slot. The

connector could be damaged, and it may

cause malfunctions.

z Do not lift up on the embroidery carriage,

and do not forcefully move it. It may cause

malfunctions.

Attaching the embroidery unit

Get the included embroidery unit ready.

a

Turn off the machine.

b

Slide the embroidery unit onto the machine

arm.

Push it in until it clicks and stops.

X The embroidery unit is attached.

c

Turn on the machine.

• For details, refer to “Turning on the machine”

(page 19).

X The confirmation message is displayed.

● Do not move the machine with the

embroidery unit in place. The embroidery

unit may be dropped and cause injury.

● Keep your hands and other objects away

from the embroidery carriage and frame.

Otherwise injury may result.

GETTING READY — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

16

d

Be sure that no objects or hands are near the

embroidery unit and press .

• When an animation is displayed on the

screen, the message above will be displayed

if you touch the screen with your finger.

X The carriage moves to its initial position.

a Carriage

CAUTION

Note

z If the machine is initialized with hands or

objects near the carriage, the screen may

return to the initial display. After removing

whatever is near the carriage, turn the power

on again.

X The screen for selecting the embroidery

pattern type is displayed.

• For details on the embroidery patterns, refer

to “Selecting Embroidery Patterns” (page 49).

Removing the embroidery unit

Make sure that the machine is completely stopped

and follow the instructions below.

a

Remove the embroidery frame.

• For details on removing the embroidery

frame, refer to “Removing the embroidery

frame” (page 48).

b

Press , and then press .

X The embroidery carriage moves into a

position where it can be stored.

c

Turn off the machine.

• For details, refer to “Turning off the machine”

(page 19).

CAUTION

● Do not put your hands or other objects

near the carriage. It may cause injury.

a

● Always turn off the machine before

removing the embroidery unit.

It may cause malfunctions if removed

when the machine is turned on.

Attaching the Embroidery Unit 17

1

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

d

Hold the release button on the bottom left of

the embroidery unit, and slowly pull the

embroidery unit to the left.

a Release button

X The embroidery unit separates from the

machine.

CAUTION

● Do not carry the embroidery unit by

holding the release button compartment.

a

GETTING READY — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

18

Turning the Machine On/Off

This section explains how to turn the machine on and off.

Power supply precautions

Be sure to observe the following precautions concerning the power supply.

WARNING

CAUTION

● Use only regular household electricity for the power source. Using other power sources may

result in fire, electric shock, or damage to the machine.

● Turn off the main power and remove the plug in the following circumstances:

• When you are away from the machine

• After using the machine

• When the power fails during use

• When the machine does not operate correctly due to a bad connection or a disconnection

• During electrical storms

● Do not use extension cords or multi-plug adapters with many other appliances plugged in to

them. Fire or electric shock may result.

● Do not touch the plug with wet hands. Electric shock may result.

● When unplugging the machine, always turn off the main power first. Always grasp the plug to

remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric

shock.

● Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted,

or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These

things may damage the cord and cause fire or electric shock. If the cord or plug is damaged,

take the machine to your authorized dealer for repairs before continuing use.

● Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a

fire may result.

Page is loading ...

Brother Innov-is 780D Owner's manual

Related papers

Other documents