2. Baby Lock
  3. Gallant Longarm

Baby Lock Gallant Longarm Assembly Instructions

  • Hello! I am an AI chatbot trained to assist you with the Baby Lock Gallant Longarm Assembly Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Page 1
Bobbin Winder Assembly Instrucons
ITEM PART # DESCRIPTION QTY
1 QM10210 MAST - THREAD TELESCOPING 1
2 QM10173 SCREW - M4 X 10 PHP ZN 2
3 QM10292 SPOOL PIN THREADS CHROME 1
4 HG00461 BOBBIN WINDER 1
5 HG00461-1 BASE PLATE-BOBBIN WINDER 1
Parts List
Step 1:Aachthebobbinwinderassembly
(item4)tothebaseplate(item5)with
twoM4X10screws(item2).
Step 2:Tightenthetwoscrewsrmlywitha
#2Phillipsscrewdriver(notprovided).
Step 3:Threadthethreadmastassembly
(item1)intothebaseplate.
Step 4:Tightenthethreadmastnutwitha
10mmwrench(notprovided).
Step 5:Threadthespoolpin(item3)into
thebaseplate.
Step 6:Tightenthespoolpinwithaprotecve
cloth,suchasaterrywashcloth,and
pliers(notprovided).
Secon 1: Bobbin Winder Assembly
1
2
3
4
5
Tools Needed (not provided):
•#2Phillipsscrewdriver
•10mmwrench
•Protecvecloth(suchasaterrywashcloth)
•Pliers
Bobbin Winder
Assembly Instrucons
September2020
Page 2
Bobbin Winder Assembly Instrucons
NOTE:Thebobbinwinderhas
adjustmentsthatwillgreatlyenhanceits
performanceandensurethequalityof
thewindonthebobbins:
Vercal Fill Adjustment:Turnthesmallertop
knob(item1)upordownunlthethread
bouncesupanddownandllsthebobbin
evenly,toptoboomwithinthebobbinanges.
Tension Adjustment:Turnthelower,larger
knob(item2)clockwisetotightenandcounter-
clockwisetoloosenthepre-tension.Turnthe
knobjust
ghtenoughforthebobbinthreadto
windrmly.Thethreadshouldnotbespongy
(tooloose),orwarpthebobbin(tooght).A
warpedbobbinisrenderedunusable.Toomuch
pre-tensionwillalsostretchthethreadduring
winding.
Amount of Fill Adjustment: Thisadjustment
determineshowfullthebobbinwillbewhen
thebobbinwindershutso.Thebobbinthread
shouldbealileinsidethebobbinanges,so
thatthethreadwillnotbetootightwithinthe
machine’sbobbin case.
Loosenthescrew(item4)onthesensor(item
3)witha#2Phillipsscrewdriverandslidethe
sensorawayfromthebobbinforafullerbobbin
ortowardthebobbinforlessthreadto be
woundonto
thebobbin.
NOTE:thebobbinwinderdoeshavea
smallthreadcuer(item5)tocutthe
threadoncethebobbiniswound.
Secon 2: Bobbin Winder Adjustments
1
2
5
3
4
Page 3
Bobbin Winder Assembly Instrucons
Secon 3: How to Wind a Bobbin on the Bobbin Winder
Step 1:Placeconeorspoolofthreadonthe
spoolpinatthebackofthebobbin
winder.
Step 2:Pullthethreadupandthroughthetop
looponthethreadmastthatshouldbe
directlyabovethespoolofthread.
Step 3:Runthethreadthroughthesmallsilver
threadguideonthebackofthetension
knobfrombacktofront.
Step 4:Flossthethreadbetweenthetwo
tensiondisksinaclockwisedirecon.
Step 5:Placeanemptybobbinonthe
bobbinpin.
Step 6:Bringthethreadupthroughtheslotin
thebobbin.
Step 7:Holdingthetailofthethread,pressthe
blueStartbuontowindthebobbin.
Oncethethreadiswindingonthe
bobbin,trimthethreadtail.
Step 8:Youcaneitherpushtheredstop
buttontostopthewindingprocess
orallow thewinderto automatically
stopwhen the sensoristriggered.
1
2
3
4
5
6
7
8
/