Sony ht fs3 User manual

Home Theatre System

4-143-280-12(1)

HT-FS3

Operating Instructions

2

GB

3

Do not expose batteries or apparatus with battery-

installed to excessive heat such as sunshine, fire or the

like.

Do not install the appliance in a confined space, such as

a bookcase or built-in cabinet.

To reduce the risk of fire, do not cover the ventilation

opening of the apparatus with newspapers, tablecloths,

curtains, etc. Do not place the naked flame sources such

as lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing, and do

not place objects filled with liquids, such as vases, on

the apparatus.

As the main plug is used to disconnect the unit from the

mains, connect the unit to an easily accessible AC

outlet. Should you notice an abnormality in the unit,

disconnect the main plug from the AC outlet

immediately.

Disposal of Old Electrical

& Electronic Equipment

(Applicable in the

European Union and

other European

countries with separate

collection systems)

This symbol on the product or

on its packaging indicates that

this product shall not be treated as household

waste. Instead it shall be handed over to the

applicable collection point for the recycling of

electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will

help prevent potential negative consequences for

the environment and human health, which could

otherwise be caused by inappropriate waste

handling of this product. The recycling of

materials will help to conserve natural resources.

For more detailed information about recycling of

this product, please contact your local Civic

Office, your household waste disposal service or

the shop where you purchased the product.

Disposal of waste

batteries (applicable in

the European Union and

other European

countries with separate

collection systems)

This symbol on the battery or on the packaging

indicates that the battery provided with this

product shall not be treated as household waste.

On certain batteries this symbol might be used in

combination with a chemical symbol. The

chemical symbols for mercury (Hg) or lead (Pb)

are added if the battery contains more than

0.0005% mercury or 0.004% lead. By ensuring

these batteries are disposed of correctly, you will

help prevent potentially negative consequences

for the environment and human health which

could otherwise be caused by inappropriate

waste handling of the battery. The recycling of

the materials will help to conserve natural

resources. In case of products that for safety,

performance or data integrity reasons require a

permanent connection with an incorporated

battery, this battery should be replaced by

qualified service staff only. To ensure that the

battery will be treated properly, hand over the

product at end-of-life to the applicable collection

point for the recycling of electrical and

electronic equipment. For all other batteries,

please view the section on how to remove the

battery from the product safely. Hand the battery

over to the applicable collection point for the

recycling of waste batteries. For more detailed

information about recycling of this product or

battery, please contact your local Civic Office,

your household waste disposal service or the

shop where you purchased the product.

Notice for customers: the following

information is only applicable to

equipment sold in countries applying EU

directives.

The manufacturer of this product is Sony Corporation,

1-7-1 Konan Minato-ku, Tokyo, 108-0075 Japan. The

Authorized Representative for EMC and product safety

is Sony Deutschland GmbH, Hedelfinger Strasse 61,

70327 Stuttgart, Germany. For any service or guarantee

matters, please refer to the addresses given in separate

service or guarantee documents.

WARNING

3

GB

On safety

• Should any solid object or liquid fall into the system,

unplug the system and have it checked by qualified

personnel before operating it any further.

• Do not climb on the subwoofer, as you may fall down

and injure yourself, or system damage may result.

On power sources

• Before operating the system, check that the operating

voltage is identical to your local power supply. The

operating voltage is indicated on the nameplate at the

rear of the subwoofer.

• If you are not going to use the system for a long time,

be sure to disconnect the system from the wall outlet

(mains). To disconnect the AC power cord (mains

lead), grasp the plug itself; never pull the cord.

• AC power cord (mains lead) must be changed only at

the qualified service shop.

• The unit is not disconnected from the mains as long as

it is connected to the AC outlet, even if the unit itself

has been turned off.

On heat buildup

Although the system heats up during operation, this is

not a malfunction. If you continuously use this system

at a large volume, the system temperature of the back

and bottom rises considerably. To avoid burning

yourself, do not touch the system.

On placement

• Place the system in a location with adequate

ventilation to prevent heat buildup and prolong the

life of the system.

• Do not place the system near heat sources, or in a

place subject to direct sunlight, excessive dust, or

mechanical shock.

• Do not place anything at the rear of the subwoofer that

might block the ventilation holes and cause

malfunctions.

• Do not cover the grill of the subwoofer.

• Do not place the system near equipment such as a TV,

VCR, or tape deck. (If the system is being used in

combination with a TV, VCR, or tape deck, and is

placed too close to that equipment, noise may result,

and picture quality may suffer. This is especially

likely when using an indoor antenna. Therefore, we

recommend using an outdoor antenna.)

• Use caution when placing the system on surfaces that

have been specially treated (with wax, oil, polish, etc.)

as staining or discoloration of the surface may result.

On operation

Before connecting other components, be sure to turn off

and unplug the system.

If you encounter color irregularity on

a nearby TV screen

Color irregularities may be observed on certain types of

TV sets.

If color irregularity is observed...

Turn off the TV set, then turn it on again after 15 to 30

minutes.

If color irregularity is observed

again...

Place the subwoofer or the speakers further away from

the TV set.

On cleaning

Clean the system with a soft dry cloth. Do not use any

type of abrasive pad, scouring powder or solvent such

as alcohol or benzine.

If you have any question or problem concerning your

system, please consult your nearest Sony dealer.

Precautions

continued

4

GB

Copyrights

This system incorporates Dolby* Digital and Pro Logic

Surround and the DTS** Digital Surround System.

* Manufactured under license from Dolby

Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are

trademarks of Dolby Laboratories.

** Manufactured under license under U.S. Patent #'s:

5,451,942; 5,956,674; 5,974,380; 5,978,762;

6,487,535 & other U.S. and worldwide patents

issued & pending. DTS and DTS Digital Surround

are registered trademarks and the DTS logos and

This system incorporates High-Definition Multimedia

Interface (HDMI™) technology.

HDMI, the HDMI logo and High-Definition

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.

“BRAVIA Sync” is a trademark of Sony Corporation.

“PLAYSTATION” is a trademark of Sony Computer

Entertainment Inc.

“S-AIR” and its logo are trademarks of Sony

Corporation.

“x.v.Colour (x.v.Color)” and “x.v.Colour (x.v.Color)”

logo are trademarks of Sony Corporation.

The system is compatible with the S-AIR function,

which allows transmission of sound between S-AIR

products wirelessly.

S-AIR receivers can be used with the system. You can

enjoy system sound in another room.

S-AIR products can be purchased as options (the S-AIR

product lineup differs depending on the area).

Notes or instructions for the S-AIR receiver in these

Operating Instructions refer only to when the S-AIR

receiver is used.

For details on the S-AIR function, see “Using an S-AIR

product” (page 49).

About the S-AIR function

5

GB

Precautions...............................................3

About the S-AIR function........................4

Getting Started

Unpacking ................................................6

Installing the system ................................7

Connecting the speakers ........................11

Connecting components with HDMI

jacks .................................................12

Connecting components without HDMI

jacks .................................................14

Setting up the sound output of the

connected component ......................16

Connecting the antenna (aerial) .............17

Connecting the other components..........19

Playback Options

Index to parts and controls.....................21

Enjoying TV...........................................24

Enjoying other components ...................25

Surround Function

Enjoying the surround effect..................27

Enjoying the sound at low volume

(NIGHT mode) ................................28

“BRAVIA” Sync Features

What is “BRAVIA” Sync?.....................29

Preparing for the “BRAVIA” Sync........29

Enjoying Blu-ray Disc/DVD..................31

(One-Touch Play)

Enjoying the TV sound from the

speakers ...........................................32

(System Audio Control)

Turning off the TV, system and connected

components ......................................33

(System Power Off)

Using the power saving function ...........34

Tuner Functions

Presetting radio stations .........................35

Listening to the radio .............................36

Using the Radio Data System (RDS).....38

Advanced Settings

Controlling the connected Sony

components with the remote ........... 39

Changing the input button assignments of

the remote........................................ 42

Settings and adjustments using the

amplifier menu ................................ 43

Using an S-AIR product........................ 49

Additional Information

Troubleshooting .................................... 59

Specifications ........................................ 62

Glossary................................................. 64

Index...................................................... 66

Table of contents

6

GB

Inserting batteries into the remote

You can control the system using the supplied remote. Insert two R6 (size AA) batteries by matching

the + and – ends on the batteries to the markings inside the compartment.

• Do not leave the remote in an extremely hot or humid place.

• Do not use a new battery with an old one.

• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a

malfunction.

• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage

from battery leakage and corrosion.

Getting Started

Unpacking

• Subwoofer (1)

•Speakers (2)

• AM loop antenna (aerial) (1)

• FM wire antenna (aerial) (1)

• Speaker cords (2)

• Digital optical cord (2.5 m) (1)

• Foot pads (8)

• Remote commander (RM-

AAU060) (1)

• R6 (size AA) batteries (2)

• Operating Instructions (1)

Notes

7

GB

Getting Started

Install the subwoofer and speakers as shown in the illustration below.

• Do not block the heat ventilation on the rear panel of the subwoofer.

• Do not cover the grill of the subwoofer.

• It is recommended to place the subwoofer on the front edge of a table or rack, etc., to accept the remote signal

correctly.

To use the speakers efficiently

Position the speakers so that the distance between each speaker and the listening position (A and B)

is the same (from 0.0 to 7.0 m).

• Place both speakers the same distance apart as they are from the listening position (to form an isosceles triangle).

• The speakers should be placed at least 0.6 m apart.

• Place the speakers forward of the TV. Make sure there are no reflecting obstacles in the way of the speakers.

Installing the system

Notes

Subwoofer

Speaker (L) Speaker (R)

Speaker (L)

TV

Speaker (R)

Subwoofer

continued

8

GB

• Both speakers should be pointed straight forward. Do not place the speakers at an angle.

• It is recommended to place the speakers on the edge of a table or rack, etc., to prevent sound reflection.

To connect the speaker cords to the speakers

The connector of the speaker cords is color-coded depending on the type of speaker.

Connect the speaker cords to match the color of the SPEAKER jacks of the subwoofer.

Be sure to match the speaker cords to the appropriate terminals on the speakers: the gray speaker

cord to +, and the gray speaker cord with a black line to –. Do not catch the speaker cord insulation

in the speaker terminals.

Correct

Incorrect

Recommended

Side view

(–) Gray with

a black line

Connector

Speaker (L): White

Speaker (R): Red

Rear of the speaker

(+) Gray

9

GB

Getting Started

To install the speakers on a flat surface

Before you install the speakers, be sure to attach the supplied foot pads to prevent vibration or

movement as shown in the illustration below.

You need to attach the supplied foot pads to both the right and left speakers.

To install the speakers on the speaker stand

For greater flexibility in positioning the speakers, use the optional WS-FV11 or WS-FV10D speaker

stand (available only in certain countries). For details, refer to the operating instructions supplied with

the speaker stand.

To install the speakers on a wall

You can install your speakers on the wall.

1 Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.

See the illustrations below.

2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm.

3 Hang the speakers on the screws.

More than 25 mm

4 mm

Hole on the rear of

the speaker

4.6 mm

10 mm

5 to 7 mm

continued

10

GB

• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach

the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where

reinforcement is applied.

• Contact a screw shop or installer regarding the wall material or screws to be used.

• Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or

improper screw installation, natural calamity, etc.

Notes

Rear of the speaker

4.6 mm

10 mm

11

GB

Getting Started

The connector of the speaker cords is color-coded depending on the type of speaker.

Connect the speaker cords to match the color of the SPEAKER jacks of the subwoofer.

Connecting the speakers

ANTENNA

AM

FM

75 COAXIAL

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

SPEAKER

ONLY FOR SS-FS3

R

L

DMPORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

Speaker (R)Speaker (L)

Red (speaker (R))

Rear of the

subwoofer

White (speaker (L))

12

GB

Sony recommends that you connect components to the system using HDMI cables.

With HDMI, you can easily enjoy both high quality sound and high quality images.

For details on the Control for HDMI function, refer to ““BRAVIA” Sync Features” (page 29).

Connect the AC power cord (mains lead) after you have finished connecting all components to the

system.

Connecting a TV monitor, projector, etc.

Connect the audio output of the TV to the audio input of the system using a digital optical cord or an

audio cord in order to listen to the TV sound from the system.

• The OPTICAL TV IN jack has priority when you connect both the audio output of the TV to the OPTICAL TV IN

and AUDIO IN jack of the system.

Connecting components with HDMI jacks

Note

ANTENNA

AM

FM

75 COAXIAL

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

SPEAKER

ONLY FOR SS-FS3

R

L

DMPORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

TV monitor, projector, etc.

A Audio cord (not supplied)

B Digital optical cord (supplied)

C HDMI cable (not supplied)

Audio/video signal

ABC

Audio signal

or

: Signal flow

Rear of the

subwoofer

13

GB

Getting Started

Connecting a Blu-ray Disc player (recorder), “PlayStation 3,”

DVD player (recorder), satellite/cable television tuner, etc.

Notes on HDMI connections

• Use a High Speed HDMI cable. If you use a Standard HDMI cable, 1080p images may not be

displayed properly.

• Sony recommends that you use an HDMI-authorized cable or Sony HDMI cable.

• Check the setup of the connected component if an image is poor or the sound does not come out of a

component connected via the HDMI cable.

• Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be

suppressed by the connected component.

• Sound may be interrupted when the number of channels or sampling frequency of audio output

signals from the playback component is changed.

• When the connected component is not compatible with copyright protection technology (HDCP), the

image and/or the sound from the HDMI TV OUT jack may be distorted or may not be output.

In this case, check the specification of the connected component.

• We do not recommend using an HDMI-DVI conversion cable.

• When TV, DIGITAL 1, DIGITAL 2, FM, AM, or DMPORT is selected, the video signal that was

selected last time is output.

• This system supports “x.v.Colour (x.v.Color)” transmission, extended by HDMI ver1.3.

ANTENNA

AM

FM

75 COAXIAL

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

SPEAKER

ONLY FOR SS-FS3

R

L

DMPORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

Blu-ray Disc player (recorder),

“PlayStation 3”

A HDMI cable (not supplied)

A

: Signal flow

Audio/video

signal

DVD player (recorder)

Audio/video

signal

Satellite/cable television tuner

Audio/video

signal

AA

Rear of the

subwoofer

14

GB

When you connect a DVD player (recorder), satellite/cable television tuner, “PlayStation 2,” etc., that

has no HDMI jacks, connect to the system using the OPTICAL DIGITAL 1 IN or COAXIAL

DIGITAL 2 IN jack.

If the satellite/cable television tuner does not have an OPTICAL OUT jack, connect the system using

the COAXIAL DIGITAL 2 IN jack. In this case, it is not necessary to connect all the cables. Connect

the audio cords according to the jacks of your components.

Connect the AC power cord (mains lead) last.

Connecting a component to the OPTICAL DIGITAL 1 IN jack

Connecting components without HDMI jacks

ANTENNA

AM

FM

75 COAXIAL

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

SPEAKER

ONLY FOR SS-FS3

R

L

DMPORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

TV monitor, projector, etc.

A

A Audio cord (not supplied)

B Digital optical cord (supplied)

C Digital optical cord (not supplied)

Video signal

: Signal flow

CB

or

Audio signal Video signal Audio signal

DVD player (recorder), “PlayStation 2,”

satellite/cable television tuner, etc.

Video signal

Rear of the

subwoofer

15

GB

Getting Started

Connecting a component to the COAXIAL DIGITAL 2 IN jack

• The OPTICAL TV IN jack has priority when you connect both the audio output of the TV to the OPTICAL TV IN

and AUDIO IN jack of the system.

Note

ANTENNA

AM

FM

75 COAXIAL

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

SPEAKER

ONLY FOR SS-FS3

R

L

DMPORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

TV monitor, projector, etc.

A

A Audio cord (not supplied)

B Digital optical cord (supplied)

C Digital coaxial cord (not supplied)

Video signal

: Signal flow

CB

or

Audio signal Video signal Audio signal

DVD player (recorder),

satellite/cable television tuner, etc.

Video signal

Rear of the

subwoofer

16

GB

Depending on the audio output settings of the connected component, the sound may output in 2 channel

sound format only. In this case, set the connected component to output the sound in multi channel sound

format (PCM, DTS, Dolby Digital). For details on audio output settings, refer to the operating

instructions supplied with the connected component.

Setting up the sound output of the connected component

17

GB

Getting Started

Connecting the AM loop antenna (aerial)

The shape and the length of the antenna (aerial) are designed to receive AM signals. Do not dismantle

or roll up the antenna (aerial).

1 Remove only the loop part from the plastic stand.

2 Set up the AM loop antenna (aerial).

3 Connect the cords to the AM antenna (aerial) terminals.

While pushing down the terminal clamp, insert the (*) part of the cords.

The cords can be connected to either terminal.

• Do not place the AM loop antenna (aerial) near the system or other AV component, as noise may

result.

• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.

4 Make sure the AM loop antenna (aerial) is connected firmly by pulling softly.

Connecting the antenna (aerial)

Note

Tip

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

P

ORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

FM

75 COAXIAL

ANTENNA

AM

*

Rear of the subwoofer

continued

18

GB

Connecting the FM wire antenna (aerial)

Connect the FM wire antenna (aerial) to the FM 75 Ω COAXIAL jack.

• Be sure to fully extend the FM wire antenna (aerial).

• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.

• Do not use the FM wire antenna (aerial) while it is bundled up.

• Insert the FM wire antenna (aerial) fully and firmly to the terminal.

• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the subwoofer to an outdoor

FM antenna (aerial) as shown below.

Notes

Tip

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

P

ORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

FM

75 COAXIAL

ANTENNA

AM

FM wire antenna (aerial)

(supplied)

FM 75 Ω COAXIAL jack

Rear of the subwoofer

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

P

ORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

FM

75 COAXIAL

ANTENNA

AM

Outdoor FM antenna

(aerial)

Rear of the subwoofer

19

GB

Getting Started

Connecting the DIGITAL MEDIA PORT adapter

You can enjoy sound from the connected component on the system by connecting the DIGITAL

MEDIA PORT adapter.

Connect the AC power cord (mains lead) last.

• Do not connect or disconnect the DIGITAL MEDIA PORT adapter while the system is turned on.

• When you connect the DIGITAL MEDIA PORT adapter, be sure the connector is inserted with the arrow mark

facing toward the arrow mark on the DMPORT jack. To detach the DIGITAL MEDIA PORT adapter, press and

hold

A and then pull out the connector.

Connecting the other components

Notes

ANTENNA

AM

FM

75 COAXIAL

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

SPEAKER

ONLY FOR SS-FS3

R

L

DMPORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

DIGITAL MEDIA PORT adapter

: Signal flow

Rear of the

subwoofer

A

continued

20

GB

Using the wireless system

The system is compatible with the S-AIR function, which allows sound transmission between the

subwoofer and S-AIR product (not supplied). When you purchase the S-AIR product, you need to

establish sound transmission.

For details, see page 49.

CAUTION

• There is no need to open the slot cover until the S-AIR product is used.

ANTENNA

AM

FM

75 COAXIAL

HDMI

TV OUTSAT/CATV INDVD INBD IN

EZW-T100

SPEAKER

ONLY FOR SS-FS3

R

L

DMPORT

DC 5V

0.7A MAX

AUDI O IN

R

TV

L

OPTICAL

TV IN

COAXIAL

DIGITAL

DIGITAL 1 IN DIGITAL 2 IN

Slot cover

Rear of the

subwoofer

Page is loading ...

Sony ht fs3 User manual

This manual is also suitable for

Sony ht fs3 User manual

Related papers

Other documents