Generac MMG35DF4 Owner's manual

Category
Power generators
Type
Owner's manual

This manual is also suitable for

SAVE THIS MANUAL FOR FUTURE REFERENCE
For technical assistance contact:
www.generacmobileproducts.com
Technical Support
1-800-926-9768
Owner’s Manual
Diesel Generator
MMG35DF4 • MMG45IF4 • MMG55DF4
Up to SN 3005615838
01306
Use this page to record important information about your unit
Record the information found on your unit data label on this
page. See
Unit and Serial Number Locations.
Engine and generator serial numbers are located on separate
data plates affixed to the engine and generator respectively.
When contacting a Generac Mobile Authorized Service Dealer
(GMASD) about parts and service, always supply the complete
model number and serial number of the unit.
Operation and Maintenance: Proper maintenance and care of
the unit ensures a minimum number of problems and keeps
operating expenses at a minimum. It is the operator’s
responsibility to perform all safety checks, to verify that all
maintenance for safe operation is performed promptly, and to
have the equipment checked periodically by a GMASD. Normal
maintenance, service and replacement of parts are the
responsibility of the owner/operator and, as such, are not
considered defects in materials or workmanship within the
terms of the warranty. Individual operating habits and usage
may contribute to the need for additional maintenance or
service.
Unit Model No.
Unit Serial No.
Engine Model No.
Engine Serial No.
Generator Model No.
Generator Serial No.
Date Purchased
(000394)
WARNING
Breathing diesel engine exhaust exposes you
to chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
Always start and operate the engine in a
well-ventilated area.
• If in an enclosed area, vent the exhaust to
the outside.
• Do not modify or tamper with the exhaust
system.
• Do not idle the engine except as necessary.
For more information go to
www.P65Warnings.ca.gov/diesel.
(000393a)
WARNING
CANCER AND REPRODUCTIVE HARM
www.P65Warnings.ca.gov.
Owner’s Manual for Mobile Generator iii
Table of Contents
Section 1: Introduction and Safety
Introduction ..................................................................1
Read This Manual Thoroughly ....................................1
How to Obtain Service .................................................1
Safety Rules .................................................................1
Safety Symbols and Meanings ...................................1
General Hazards ...........................................................2
Trailer Hazards .............................................................2
Electrical Hazards ........................................................3
Explosion and Fire Hazards ........................................3
Fuel Hazards .................................................................4
Engine Safety ...............................................................4
Operating Safety ..........................................................5
Positioning the Unit .....................................................5
Lowering Trailer Tongue .............................................5
Towing Safety ...............................................................5
Hitch and Coupling ......................................................5
Safe Towing Techniques .............................................6
Reporting Trailer Safety Defects ................................6
Safety and Operating Decals ......................................7
Section 2: General Information
Specifications .............................................................11
Unit Dimensions .........................................................12
Unit and Serial Number Locations ...........................13
Altitude and Temperature Limitations .....................13
Component Locations ...............................................14
Exterior ......................................................................14
Connection Panel ......................................................15
Control Panel .............................................................16
Genset Controller .......................................................17
Controller Modes .......................................................19
Operator Pages .........................................................19
Maintenance Alarms ..................................................21
Selective Catalytic Reduction (SCR) Monitoring ....22
Voltage Selector Switch ............................................23
Lockout Function .......................................................23
Section 3: Operation
Pre-start Checklist .....................................................25
Manually Starting the Unit .........................................25
AUTO (Remote) Starting the Unit .............................26
Low Idle Switch ..........................................................26
Wet Stacking ..............................................................26
Cold Weather Operation ............................................27
Using a Booster Battery or Charger (if equipped) ..28
Generator Output Connections ................................28
Generator Cam Lock Connections (If Equipped) ....29
Using the Voltage Selector Switch ...........................29
Fine Voltage Adjustment ...........................................30
Voltage Regulator ......................................................30
Customer Convenience Receptacles .......................30
Main Circuit Breaker ..................................................30
DOC and SCR Cleaning Operations .........................30
Disabling Automatic (AUTO) Exhaust After-Treatment
Cleaning (If Equipped) ...............................................31
Force a Manual Exhaust After-Treatment Cleaning 31
Enable Exhaust After-Treatment Cleaning ................31
Transfer Switch ..........................................................31
Alternative Load Device (ALD) (If Equipped) ..........32
AUTO Exercise Timer ................................................32
Accessing the Configuration Menu ............................32
Set the Controller Clock ............................................32
Set the Schedule .......................................................32
Setting Up a Daily Scheduled Run ............................33
Set the Unit to AUTO Mode .......................................33
Shutting Down the Unit .............................................33
Emergency Stop Switch ............................................33
Idle Switch ..................................................................33
Using ECU Override ...................................................33
Towing the Unit ..........................................................34
Lifting the Unit ............................................................34
Section 4: Maintenance
Emissions Information ..............................................37
Maintenance ...............................................................37
Daily Walk Around Inspection ..................................37
Belt Tensioners ..........................................................37
General Maintenance .................................................37
Engine Oil Recommendations ..................................38
Coolant Recommendation ........................................38
Basic Maintenance Schedule ....................................39
Engine Break-In Requirements—Isuzu ....................41
iv Owner’s Manual for Mobile Generator
Engine Break-In Requirements—John Deere .........41
Resetting Maintenance Alarms ................................ 41
Exhaust Filter Service Requirements ......................41
Checking Generator Drive Plate Torque .................41
Jack Maintenance ...................................................... 42
Side-Wind Models ..................................................... 42
Top-Wind Models ...................................................... 42
Trailer Wheel Bearings .............................................. 42
Section 5: Troubleshooting
General Troubleshooting ..........................................43
Section 6: Wiring Diagrams
3-Position AC Box ..................................................... 45
3-Position AC Box ..................................................... 46
4-Position AC Box ..................................................... 47
4-Position AC Box ..................................................... 48
Receptacles ................................................................49
Engine Heater ............................................................ 49
Wiring Buck (If Equipped) ......................................... 50
Power Zone PMG .......................................................50
Control Box ................................................................51
Trailer Lights .............................................................. 52
Trailer Brakes .............................................................53
12-Volt Battery Charger ............................................ 54
Power Zone Low Oil Level (If Equipped) ................. 54
Owner’s Manual for Mobile Generator 1
Section 1: Introduction and Safety
Introduction
Thank you for purchasing a Generac Mobile product. This
unit has been designed to provide high performance,
efficient operation, and years of use when maintained
properly.
The information in this manual is accurate based on
products produced at the time of publication. The manu-
facturer reserves the right to make technical updates,
corrections, and product revisions at any time without
notice.
Read This Manual Thoroughly
If any section of this manual is not understood, contact your
nearest GMASD, or contact Generac Mobile Technical
Service at 1-800-926-9768 or
www.generacmobileproducts.com
with any questions or
concerns.
The owner is responsible for proper maintenance and safe
use of the equipment. Comply with regulations the
Occupational Safety and Health Administration (OSHA)
has established, or with equivalent standards. Also, verify
that the unit is applied, used, and maintained in accordance
with the manufacturer's instructions and recommendations.
Do nothing that might alter safe application/usage and
render the unit in noncompliance with the aforementioned
codes, standards, laws, and regulations
.
Save these instructions for future reference. This manual
contains important instructions for the unit that should be
followed during setup, operation and maintenance of the
unit and battery. ALWAYS supply this manual to any
individual that will use this machine.
How to Obtain Service
When the unit requires servicing or repairs, contact a
GMASD for assistance. Service technicians are factory-
trained and are capable of handling all service needs. For
assistance locating a dealer, go to https://www.gener-
acmobileproducts.com/parts-service/find-service.
When contacting a GMASD about parts and service,
always supply the complete model and serial number of
the unit as given on the data decal located on the unit.
Record the model and serial numbers in the spaces pro-
vided on the front cover of this manual.
Safety Rules
The manufacturer cannot anticipate every possible
circumstance that might involve a hazard. The warnings in
this manual, and on tags and decals affixed to the unit are,
therefore, not all inclusive. If using a procedure, work
method or operating technique that the manufacturer does
not specifically recommend, verify it is safe for others. Also
make sure the procedure, work method or operating
technique utilized does not render the equipment unsafe.
Safety Symbols and Meanings
Throughout this publication, and on tags and decals affixed
to the unit, DANGER, WARNING, CAUTION and NOTE
blocks are used to alert personnel to special instructions
about a particular operation that may be hazardous if
performed incorrectly or carelessly. Observe them
carefully. Their definitions are as follows:
NOTE: Notes contain additional information important to
a procedure and will be found within the regular text of
this manual.
These safety alerts cannot eliminate the hazards that they
indicate. Common sense and strict compliance with the
special instructions while performing the action or service
are essential to preventing accidents.
(000100a)
Consult Manual. Read and understand manual
completely before using product. Failure to
completely understand manual and product
could result in death or serious injury.
WARNING
(000001)
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
(000002)
WARNING
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
(000003)
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
2 Owner’s Manual for Mobile Generator
Introduction and Safety
General Hazards
Trailer Hazards
(000103)
Asphyxiation. Running engines produce carbon
monoxide, a colorless, odorless, poisonous
gas. Carbon monoxide, if not avoided, will
result in death or serious injury.
DANGER
DANGER
Asphyxiation. Do not operate unit without
a properly functioning exhaust system.
Doing so will result in death or serious injury.
(000340)
(000209b)
WARNING
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.
(000107)
Hearing Loss. Hearing protection is
recommended when using this machine.
Failure to wear hearing protection could
result in permanant hearing loss.
WARNING
Vision loss. Eye protection is required when
operating unit. Failure to wear appropriate eye
protection could result in vision loss or serious
injury.
(000407)
WARNING
(000111)
WARNING
Moving Parts. Keep clothing, hair, and
appendages away from moving parts. Failure
to do so could result in death or serious injury.
(000108)
WARNING
Hot Surfaces. When operating machine, do not
touch hot surfaces. Keep machine away from
combustibles during use. Hot surfaces could
result in severe burns or fire.
WARNING
Equipment damage. Do not attempt to start or operate
a unit in need of repair or scheduled maintenance.
Doing so could result in serious injury, death, or
equipment failure or damage.
(000291)
WARNING
Risk of injury. Do not operate or service this machine
if not fully alert. Fatigue can impair the ability to
service this equipment and could result in death or
serious injury.
(000215)
(000182a)
WARNING
Equipment damage. Only qualified service personnel may
install, operate, and maintain this equipment. Failure to
follow proper installation requirements could result in death,
serious injury, and equipment or property damage.
CAUTION
(000229)
Equipment or property damage. Do not block air
intake or restrict proper air flow. Doing so could
result in unsafe operation or damage to unit.
WARNING
(000233a)
Personal injury. Trailer must be securely coupled to the
hitch with the chains correctly attached. Uncoupled or
unchained towing could result in death or serious injury.
(000231a)
Personal injury. Do not operate unit during transport.
Doing so could result in death, serious injury, or
property damage.
WARNING
(000234a)
Crushing hazard. Verify unit is properly secured and
on level ground. An unsecured unit can suddenly roll
or move, causing death or serious injury.
WARNING
WARNING
Property or Equipment Damage. Tighten wheel lug
nuts after first 50 miles to factory specifications.
Failure to do so could result in death, serious injury,
property or equipment damage.
(000235)
Owner’s Manual for Mobile Generator 3
Introduction and Safety
Electrical Hazards
Lifting Hazards
Explosion and Fire Hazards
(000145)
DANGER
Electrocution. In the event of electrical accident,
immediately shut power OFF. Use non-conductive
implements to free victim from live conductor. Apply
first aid and get medical help. Failure to do so will
result in death or serious injury.
(000104)
DANGER
Electrocution. Water contact with a power
source, if not avoided, will result in death
or serious injury.
(000144)
DANGER
Electrocution. Contact with bare wires,
terminals, and connections while generator
is running will result in death or serious injury.
(000152)
DANGER
Electrocution. Verify electrical system is
properly grounded before applying power.
Failure to do so will result in death or serious
injury.
(000123)
DANGER
Electrocution. Turn utility supply OFF before
working on utility connections of the transfer
switch. Failure to do so will result in death or
serious injury.
(000150)
Electrocution. Never connect this unit to the electrical
system of any building unless a licensed electrician
has installed an approved transfer switch. Failure to
do so will result in death or serious injury.
DANGER
(000238)
Explosion. Batteries emit explosive gases.
Always disconnect negative battery cable
first to avoid spark. Failure to do so could
result in death or serious injury.
WARNING
Personal injury. Failure to properly connect
lifting cables, chains, or straps could result in
death, serious injury, or property damage.
(000346)
WARNING
WARNING
Personal Injury. Do not use lifting eye if there are
signs of damage or corrosion. Doing so could result
in death, serious injury, or property damage.
(000433)
WARNING
Personal Injury. Do not use lifting eye other than as
directed. Doing so could result in death, serious
injury, or property damage.
(000434)
(000351)
Personal Injury. Verify all fasteners are properly
tightened prior to lifting unit. Failure to do so could
result in death, serious injury, or property damage.
WARNING
(000105)
Explosion and Fire. Fuel and vapors are extremely
flammable and explosive. Add fuel in a well
ventilated area. Keep fire and spark away. Failure
to do so will result in death or serious injury.
DANGER
WARNING
(000281)
Fire risk. Fuel and vapors are extremely
flammable. Do not operate indoors. Doing
so could result in death, serious injury, or
property or equipment damage.
(000147)
WARNING
Risk of Fire. Unit must be positioned in a
manner that prevents combustible material
accumulation underneath. Failure to do so
could result in death or serious injury.
4 Owner’s Manual for Mobile Generator
Introduction and Safety
Battery Hazards
Always recycle batteries in accordance with local laws
and regulations. Contact your local solid waste collection
site or recycling facility to obtain information on local
recycling processes. For more information on battery
recycling, visit the Battery Council International website
at: http://batterycouncil.org
Fuel Hazards
DO NOT fill fuel tank near an open flame, while
smoking, or while engine is running. DO NOT fill
tank in an enclosed area with poor ventilation.
DO NOT operate with the fuel tank cap loose or
missing.
Engine Safety
Internal combustion engines present special hazards
during operation and fueling. Failure to follow the safety
guidelines described below could result in severe injury or
death. Read and follow all safety alerts described in the
engine operator's manual. A copy of this manual was
supplied with the unit when it was shipped from the factory.
DO NOT run engine indoors or in an area with poor
ventilation. Verify engine exhaust cannot seep into
closed rooms or ventilation equipment.
DO NOT clean air filter with gasoline or other types
of low flash point solvents.
DO NOT operate the unit without a functional
exhaust system.
Shut the engine down if any of the following
conditions exist during operation:
•Abnormal change in engine speed.
•Loss of electrical output.
•Equipment connected to the unit overheats.
•Sparking occurs.
•Engine misfires or there is excessive engine/gen-
erator vibration.
•Protective covers are loose or missing.
•Ambient air temperature is above 120°F (49°C).
(000188)
DANGER
Electrocution. Do not wear jewelry while
working on this equipment. Doing so will
result in death or serious injury.
(000137a)
WARNING
Explosion. Batteries emit explosive gases while
charging. Keep fire and spark away. Wear protective
gear when working with batteries. Failure to do so
could result in death or serious injury.
(000162)
Explosion. Do not dispose of batteries in a fire.
Batteries are explosive. Electrolyte solution can cause
burns and blindness. If electrolyte contacts skin or eyes,
flush with water and seek immediate medical attention.
WARNING
(000163a)
Risk of burn. Do not open or mutilate batteries.
Batteries contain electrolyte solution which can cause
burns and blindness. If electrolyte contacts skin or
eyes, flush with water and seek immediate medical
attention.
WARNING
WARNING
(000228)
Environmental Hazard. Always recycle batteries at an
official recycling center in accordance with all local
laws and regulations. Failure to do so could result in
environmental damage, death, or serious injury.
(000192)
DANGER
Explosion and fire. Fuel and vapors are extremely
flammable and explosive. No leakage of fuel is
permitted. Keep fire and spark away. Failure to do
so will result in death or serious injury.
(000174)
DANGER
Risk of fire. Allow fuel spills to completely dry
before starting engine. Failure to do so will
result in death or serious injury.
Owner’s Manual for Mobile Generator 5
Introduction and Safety
Operating Safety
Positioning the Unit
The area immediately surrounding the unit should
be dry, clean, and free of debris.
If the unit is equipped with a frame grounding stud,
follow any local, state, and National Electrical Code
(NEC) guidelines when connecting.
Lowering Trailer Tongue
For units shipped with the trailer tongue in the upright
position, follow the steps below to lower the tongue.
1. Elevate the unit using a hoist or forklift, or use the
jack located on the trailer tongue.
NOTE: If using the front jack for support, it must first be
moved to the jack mount location nearest the frame.
2. See Figure 1-1 Remove the mounting hardware
securing the tongue shipping brace to the trailer
frame (A).
Figure 1-1. Lowering Tongue Trailer
3. Remove the shipping brace and slide it into the
trailer tube opening. Secure the brace to the trailer
with the bolt located on the underside of the trailer
(B) and a new nylon locking nut.
4. See Figure 1-2. Flip the trailer tongue down and
reinstall the bolts and washers removed in step two
using two new nylon locking nuts (A). DO NOT
reuse the nylon locking nuts. Tighten the bolts to
80–109 ft-lb (108–148 Nm)
Figure 1-2. Lowering Tongue Trailer
NOTE: If the jack was used to support the unit while
removing the shipping brace, the jack must be moved
back to the tongue location before the unit can be towed.
Connect the trailer tongue to a vehicle or other support
and move the jack to the tongue location.
5. Tighten the bolt inside the jack mounting tube
nearest the frame.
6. See Figure 1-3 Remove the mounting hardware
from the front hood actuator clearance hole panel
(A). Tilt the panel forward. Reinstall the hardware
to secure the panel.
Figure 1-3. Lowering Tongue Trailer
Towing Safety
Towing a trailer requires care. Both the trailer and vehicle
must be in good condition and securely fastened to each
other to reduce the possibility of an accident. Some states
require that large trailers be registered and licensed.
Contact your local Department of Transportation office to
check on license requirements for your particular unit.
Hitch and Coupling
Verify the hitch and coupling on the towing vehicle
are rated equal to, or greater than, the trailer's
Gross Vehicle Weight Rating (GVWR).
Verify the trailer hitch and the coupling are
compatible. Verify the coupling is securely fastened
to the vehicle.
(000234a)
Crushing hazard. Verify unit is properly secured and
on level ground. An unsecured unit can suddenly roll
or move, causing death or serious injury.
WARNING
B
A
008594
008595
A
008596
A
6 Owner’s Manual for Mobile Generator
Introduction and Safety
DO NOT tow trailer using defective parts. Inspect
the hitch and coupling for wear or damage.
Connect safety chains in a crossing pattern under
the tongue.
Before towing the unit, verify the weight of the
trailer is equal across all tires. On trailers with
adjustable height hitches, adjust the angle of the
trailer tongue to keep the trailer as level as
possible.
Safe Towing Techniques
Practice turning, stopping and backing up in an
area away from heavy traffic prior to transporting
the unit.
Maximum recommended speed for highway towing
is 45 mph (72 km/h). Recommended off-road
towing speed is 10 mph (16 km/h) or less,
depending on terrain.
When towing, maintain extra space between
vehicles and avoid soft shoulders, curbs and
sudden lane changes.
Reporting Trailer Safety Defects
If you believe your trailer has a defect which could cause
a crash or could cause injury or death, you should
immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying Generac
Mobile.
If NHTSA receives similar complaints, it may open an
investigation; and if it finds that a safety defect exists in a
group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in
an individual problem between you, your GMASD, or
Generac Mobile.
To contact NHTSA, you may either call the Auto Safety
Hotline toll-free at 1-888-327-4236 (TTY:1-800-424-9153),
go to http://www.safercar.gov; or write to:
Administrator
NHTSA
1200 New Jersey Avenue S.E.
Washington, DC 20590
You can also obtain other information about motor vehicle
safety from http://www.safercar.gov.
Owner’s Manual for Mobile Generator 7
Introduction and Safety
Safety and Operating Decals
This unit features numerous safety and operating decals.
These decals provide important operating instructions and
warn of dangers and hazards. The following diagrams
illustrate decal locations and descriptions.
Replace any missing or hard-to-read decals and use care
when washing or cleaning the unit. Decal part numbers
can be found in the parts manual at
www.generacmobileproducts.com.
ID Description ID Description
1 Towing Instructions 19 Starting and Stopping Generator
2 Ultra Low Sulfur Fuel Only 20 Operating Instructions
3 Danger: Diesel Fuel 21 Terminal Connections (Voltage Selector Switch)
4 Tie-Down Location 22 Electrical Backfeed Danger
5 Oil Drain 23 Remote Start Terminal Connections
6 Coolant Drain 24 Neutral Bonded to Frame
7 Warning: Hot Surface 25 CAM Locks
8 Unit Lift Point 26 Connection Terminal Lugs
9 Warning: Automatic Starting 27 Fan Clutch (if equipped)
10 Electric Shock Hazard 28 Fuel Heater (if equipped)
11 Warning: Hot Surface 29 Start/Prestart
12 Do Not Operate with Guards Removed 30 Fuel Transfer
13 Ground 31 Danger: Read Owner’s Manual Before Operation
14 Battery Disconnect 32 Circuit Breaker
15 Secondary Filter 33 Breaker
16 Primary Filter 34 Controller Toggle Switches
17 Warning: Hot Surface/Moving Parts 35 Read Owner’s Manual Before Operation
18 Open Upper Door First
8 Owner’s Manual for Mobile Generator
Introduction and Safety
Figure 1-4. Exterior Decals
6PJNJ
8/75$/2:
68/)85
)8(/21/<
'$1*(5
*()$+5
3(/,*52
'$1*(5
',(6(/
5HDGRSHUDWRUVPDQXDO
8VHKLWFKUDWHGIRUWUDLOHUVJURVVYHKLFOHZHLJKW
UDWLQJ
6HFXUHO\DWWDFKWUDLOHUWRWRZYHKLFOH
$WWDFKVDIHW\FKDLQVXVLQJDFURVVSDWWHUQ
$WWDFKEUHDNGRZQFKDLQWRYHKLFOH
&KHFNWUDLOHUOLJKWV
72:,1*,16758&7,216
,16758&&,21(63$5$5(02/48(
/HDHOPDQXDOGHORSHUDGRU
8VHXQHQJDQFKHDGHFXDGRSDUDOD³FDSDFLGDG
GHSHVREUXWRGHOYHKtFXOR´GHOUHPROTXH
(QJDQFKHILUPHPHQWHHOUHPROTXHDOYHKtFXOR
GHUHPROTXH
(QJDQFKHODVFDGHQDVGHVHJXULGDGHQ
IRUPDFUX]DGD
(QJDQFKHDOYHKtFXORODFDGHQDGHHPHUJHQFLD
SDUDDYHUtDV
5HYLVHODVOXFHVGHOUHPROTXH
$%6&+/(33$1:(,681*(1
/LUHOHPDQXHOGHO¶XWLOLVDWHXU
8WLOLVHUXQDWWHODJHFRQYHQDQWDXSRLGVQRPLQDO
EUXWGHODUHPRUTXH
$UULPHUVROLGHPHQWODUHPRUTXHDXYpKLFXOHWUDFWHXU
3RVHUOHVFKDvQHVGHVpFXULWpHQOHVFURLVDQW
)L[HUODFKDvQHGHUHPRUTXDJHDXYpKLFXOH
9pULILHUOHVIHX[GHODUHPRUTXH
,16758&7,216'(5(02548$*(
%HQXW]HUKDQGEXFKOHVHQ
$QKlQJHYRUULFKWXQJYHUZHQGHQGLHGHU
Ä*HVDPWEHWULHEVJHZLFKWVNODVVH´GHV
)DKU]HXJVHQWVSULFKW
$QKlQJHUVLFKHUDP
$EVFKOHSSIDKU]HXJEHIHVWLJHQ
6LFKHUKHLWVNHWWHQEHU.UHX]DQEULQJHQ
$EUHLNHWWHDP)DKU]HXJDQEULQJHQ
$QKlQJHUOHXFKWHQSUIHQ
008084
1
6
5
4
4
3
2
Owner’s Manual for Mobile Generator 9
Introduction and Safety
Figure 1-5. Interior Decals
WARNING
WARNUNG
ADVERTENCIA
AVERTISSEMENT
WARNUNG
ADVERTENCIA
AVERTISSEMENT
WARNING
La génératrice peut démarrer
automatiquement, ce qui peut entraîner
des blessures graves. Débrancher la
batterie avant de faire l’entretien.
Generator can automatically start
which can cause serious injury.
Disconnect battery before servicing.
Der Generator kann automatisch
anspringen und schwere Verletzungen
verursachen. Vor der Instandsetzung
die Batterieverbindungen lösen.
El generador puede arrancar
automáticamente, lo que puede causar
graves lesiones. Desconecte la batería
antes de realizar el servicio técnico.
BATTERY
DISCONNECT
HINWEIS
AVISO
AVIS
NOTICE
PRIMARY
FILTER
SECONDARY
FILTER
OPEN UPPER
DOOR FIRST
TO ACCESS
CONNECTIONS
La génératrice peut démarrer
automatiquement, ce qui peut entraîner
des blessures graves. Débrancher la
batterie avant de faire l’entretien.
Generator can automatically start
which can cause serious injury.
Disconnect battery before servicing.
Der Generator kann automatisch
anspringen und schwere Verletzungen
verursachen. Vor der Instandsetzung
die Batterieverbindungen lösen.
El generador puede arrancar
automáticamente, lo que puede causar
graves lesiones. Desconecte la batería
antes de realizar el servicio técnico.
WARNING
WARNUNG
ADVERTENCIA
AVERTISSEMENT
WARNUNG
ADVERTENCIA
AVERTISSEMENT
WARNING
008085
17
16
15
14
13
12
11
10
9
8
7
8
17
12
9
13
18
10
10 Owner’s Manual for Mobile Generator
Introduction and Safety
Figure 1-6. Control Panel Decals
VOLTAGE
REGULATION
L1 Black
L2 Blue
L3 Red
N White
G Green
Located Near
Cam Locks
Optional 4th Position on Voltage Selector Switch
T1
L1
T4
T7
T10
N
T2
L2
T8
T5
T9
T6
T3
L3
T11
T12
L-N
L-L
L1 - L2 = 480V L1 - N = 277V
L2 - L3 = 480V L2 - N = 277V
L3 - L1 = 480V L3 - N = 277V
N =
T4
T7
T10
T1
L1
L2
T8
T2
T9
T3
T6
T11
L3
T5
T12
N
L-N
L-L
L1 - L2 = 208V L1 - N = 120V
L2 - L3 = 208V L2 - N = 120V
L3 - L1 = 208V L3 - N = 120V
N =
T1
L1
T4
T7
T10
T2
L2
T8 T5
T9
T6
T3
L3
T11
T12
L-L
N
L-N
L-N
T4
T1
T6
T2
T12
T8
T5
T3
T10 T7
T11
T9
L3
N
L1
120V120V
240V
TERMINAL CONNECTIONS / KLEMMENBELEGUNG / CONEXIONES DE TERMINALES / BRANCHEMENTS AU TERMINAL
L1 - L2 = 240V L1 - N = 120V
L2 - L3 = 240V L2 - N = 208V
L3 - L1 = 240V L3 - N = 120V
N =
120/
240V 3PH
277/
480V
120/
208V
120/
240V
1PH
120/240V 3-PHASE
120/
240 V
277/
480 V
120/
208 V
120/
240 V
480
277
208
120
277/480V 3-PHASE 120/208V 3-PHASE
120/240V 1-PHASE
240
120
480
277
208
120
240
120
208
120
277/480
120/208
120/240
277/480
120/208
120/240
277/480
120/208
120/240
L1 - L3 = 240V L1 - N = 120V
L2 - N = -------
L3 - N = 120V
N=
Never change switch position with engine running. Results in damage to machine.
Bei laufendem Motor darf die Schalterstellung nicht verändert werden. Dies führt zur Beschädigung der Maschine.
Nunca cambie la posición del interruptor con el motor en funcionamiento. Puede causar daños a la máquina.
Ne jamais changer la position du commutateur lorsque le moteur fonctionne. Vous pourriez endommager l’appareil.
AVERTISSEMENT
208
120
480
277
240
120
ADVERTENCIA
WARNUNG
WARNING
STOP
NEUTRAL (L0) BONDED TO FRAME
NULLLEITER (L0) AM RAHMEN ANGESCHLOSSEN
NEUTRO (L0) CONECTADO AL BASTIDOR
POSITION NEUTRE
(L0)
LORSQUE FIXÉ AU CADRE
REMOTE START/TERMINAL CONNECTIONS
FERNSTART/KLEMMENBELEGUNG
ARRANQUE REMOTO/CONEXIONES DE TERMINALES
DÉMARRAGE À DISTANCE ET BRANCHEMENTS AU TERMINAL
FUEL
TRANSFER
PRESTART
START
FUEL
HEATER
FAN
CLUTCH
Located on relays
inside electrical box
L1 L2 L3
STARTING THE GENERATOR
DAS STARTEN DES GENERATORS / COMIENZO DEL GENERADOR /
COMMENCEMENT DU GÉNÉRATEUR
STOPPING THE GENERATOR
DAS AUFHÖREN DES GENERATORS / PARADA DEL GENERADOR /
ARRÊT DU GÉNÉRATEUR
A0000639819
BETRIEBSANLEITUNG
MODE D’EMPLOI
Avant de commencer
1. Lire le manuel de l’utilisateur.
2. Stabiliser l’appareil à niveau.
3. Bloquer les roues.
4. Effectuer la mise à la terre de l’appareil.
5. Vérifier le niveau de tous les fluides.
Démarrage manuel
1. Débrancher toutes les charges externes.
2. Actionner le sélectionneur de tension.
3. Tirez sur le bouton d’arrêt d’urgence.
4. Déplacez le commutateur de commande à la position
« CONTROL ON » (COMMANDE EN MARCHE).
5. Enfoncez le bouton « START ENGINE » (MOTEUR
EN MARCHE).
Démarrage à distance
1. Consulter le manuel de l’utilisateur.
Arrêt
1. Débrancher toutes les charges externes.
2. Enfoncez le bouton « ENGINE STOP »
(ARRÊT DU MOTEUR).
3. Déplacez le commutateur de commande et placez-le
à la position « CONTROL OFF » (ARRÊT DE COMMANDE).
4. Faire le plein d’essence.
Antes de comenzar
1. Lea el manual del operador.
2. Nivele la unidad.
3. Bloquee las ruedas.
4. Conecte la unidad a tierra.
5. Revise los niveles de todos los líquidos.
Arranque manual
1. Desconecte todas las cargas externas.
2. Configure el interruptor del selector de voltaje.
3. Jale el botón de parada de emergencia.
4. Mueva el interruptor de control a la posición
“CONTROL ON” (control encendido).
5. Empuje el botón “ENGINE START” (arrancar motor).
Arranque remoto
1. Consulte el manual del operador.
Parada
1. Desconecte todas las cargas externas.
2. Empuje el botón “ENGINE STOP” (parar motor).
3. Mueva el interruptor de control a la posición
“CONTROL OFF” (control apagado).
4. Llene el tanque de combustible.
OPERATING INSTRUCTIONS
INSTRUCCIONES DE OPERACIÓN
Vor dem Starten
1. Benutzerhandbuch lesen.
2. Gerät waagerecht stellen.
3. Räder blockieren.
4. Gerät erden.
5. Alle Flüssigkeitspegel prüfen.
Manuelles Starten
1. Alle externen Lasten abschalten.
2. Spannungswahlschalter einstellen.
3.
Notstoppknopf herausziehen.
4.
Regelschalter auf „CONTROL ON“
(REGELUNG EIN) stellen.
5.
„MOTORSTARTKNOPF“ drücken.
Fernstart
1. Siehe Benutzerhandbuch.
Anhalten
1. Alle externen Lasten abschalten.
2.
„MOTORSTOPPKNOPF“ drücken.
3.
Regelschalter auf „CONTROL OFF“
(REGELUNG AUS) stellen.
4. Treibstofftank befüllen.
Before starting
1. Read operator's manual.
2. Level unit.
3. Block wheels.
4. Ground unit.
5. Check all fluid levels.
Manual starting
1. Disconnect all external loads.
2. Set voltage selector switch.
3. Pull out emergency stop button.
4. Move control switch to "CONTROL ON" position.
5. Push “ENGINE START” button.
Remote start
1. See operator's manual.
Stopping
1. Disconnect all external loads.
2. Push “ENGINE STOP” button.
3. Move control switch to "CONTROL OFF" position.
4. Fill fuel tank.
Improper connection of generator to a building’s electrical system can allow electrical current from
the generator to backfeed into utility lines. This may result in electrocution of utility workers, fire or
explosion. Connections to a building’s electrical system must be made by a qualified electrician
and comply with all applicable laws and electrical codes.
Der unsachgemäße Anschluss eines Generators an das Stromnetz eines Gebäudes kann eine
Rückführung des elektrischen Stroms vom Generator in die Stromleitungen verursachen. Dies kann u.
U. zu tödlichem Stromschlag bei EVU-Mitarbeitern, Brand oder Explosion führen. Anschlüsse an das
Gebäudestromnetz müssen von einem Elektriker vorgenommen werden und es müssen dabei alle
einschlägigen Gesetze und elektrischen Vorschriften eingehalten werden.
La conexión inadecuada del generador al sistema eléctrico de un edificio puede hacer que la corriente
eléctrica del generador se retroalimente en las líneas de servicios públicos. Esto puede provocar la
electrocución de los trabajadores de servicios públicos, incendios o explosiones. Las conexiones al
sistema eléctrico de un edificio deben ser realizadas por un electricista calificado, y cumplir con todas
las leyes y todos los códigos de electricidad aplicables.
Le raccordement inadéquat de la génératrice au système électrique d’un immeuble peut permettre au
courant électrique produit par la génératrice de refouler dans le réseau public. Les ouvriers de la
compagnie d’électricité pourraient subir une électrocution, et un feu ou une explosion pourraient
survenir. Le raccordement au système électrique d’un immeuble doit être confié à un électricien
compétent et respecter l’ensemble des lois et codes en vigueur en matière d’électricité.
30
31
33
26
30
29
28
27
13
24
25
34
19
21
23
26
2626
32
008087b
20
22
Owner’s Manual for Mobile Generator 11
Section 2: General Information
Specifications
Description Unit of Measure MMG35DF4 MMG45IF4 MMG55DF4
Engine
Make (Model)
John Deere
®
(3029HFG03)
Isuzu
®
(4LE2XAGV01)
John Deere
(3029HFG03)
Rated Power Output hp (kW) 48 (36) 64 (48) 74 (55)
Operating Speed rpm 1,800 1,800 1,800
Fuel Consumption, 100% load, prime gph (Lph) 2.9 (11.0) 3.3 (12.5) 3.9 (14.8)
Fuel Consumption, 75% load, prime gph (Lph) 2.3 (8.7) 2.5 (9.4) 3.2 (12.1)
Fuel Consumption, 50% load, prime gph (Lph) 1.7 (6.4) 1.7 (6.4) 2.3 (8.7)
EPA Emissions Certification Tier 4 final 4 final 4 final
Battery—Voltage (Quantity of
Batteries)
VDC (qty) 12 (1) 12 (1) 12 (1)
Battery—Rating CCA 720 720 720
Capacities
Fuel Tank—Usable gal (L) 90 (341) 90 (341) 90 (341)
Maximum Run Time—100% Load hr 31.0 27.0 23.0
Coolant—System gal (L) 18 (17) 18 (17) 18 (17)
Oil—Crankcase qt (L) 11 (10.4) 12 (11.4) 11 (10.4)
Generator
Make (Model)
Marathon
®
(284CSL1542)
Marathon
(285PSL1700)
Marathon
(286PSL1701)
Insulation Class H H H
Poles qty 4 4 4
Voltage Regulation AVR AVR AVR
Frequency Hz 60 60 60
Power Output
3Ø Standby kW (kVA) 31 (39) 44 (55) 48 (60)
208/480 V A 108 (47) 153 (66) 167 (72)
240 V A 94 122 144
3Ø Prime kW (kVA) 29 (36) 38 (47) 44 (55)
208/480 V A 100 (43) 130 (57) 153 (66)
240 V A 86 114 122
1Ø Standby kW (kVA) 30 (30) 40 (40) 46 (46)
240 V A 125 167 192
1Ø Prime kW (kVA) 27 (27) 33 (33) 42 (42)
240 V A 113 138 175
Power Factor: 3Ø, 1Ø 0.8, 1.0 0.8, 1.0 0.8, 1.0
AC Distribution
Circuit Breaker Size A 125 225 225
Trailer
Hitch—Standard size, type
2 in (50.8 mm),
ball
2 in (50.8 mm),
ball
2 in (50.8 mm),
ball
Maximum Tire Pressure psi (kPA) 65 (448) 65 (448) 65 (448)
Weight
Skid Mounted—Dry lb (kg) 3,125 (1,418) 2,843 (1,290) 3,305 (1,499)
Skid Mounted—Operating lb (kg) 3,860 (1,751) 3,580 (1,624) 4,040 (1,833)
Trailer Mounted—Dry lb (kg) 3,725 (1,690) 3,363 (1,525) 3,905 (1,771)
Trailer Mounted—Operating lb (kg) 4,460 (2,023) 4,100 (1,860) 4,640 (2,105)
Specifications are subject to change without notice.
12 Owner’s Manual for Mobile Generator
General Information
Unit Dimensions
Figure 2-1. Unit Dimensions—MMG35DF4, MMG45IF4, MMG55DF4
LW H
Skid Mounted 95 in (2.41 m) 39 in (0.99 m) 65 in (1.65 m)
Trailer Mounted 152 in (3.81 m) 58 in (1.45 m) 83 in (2.11 m)
H
W
L
H
W
L
01906
Owner’s Manual for Mobile Generator 13
General Information
Unit and Serial Number Locations
See Figure 2-2 to locate the unit ID tag (A) (located
behind breaker door beneath breakers) and vehicle
identification number (VIN) tag (B). Important information
such as the unit model number, serial number, VIN, and
tire loading information are listed on these tags. Record
the information from these tags in the event the tags are
lost or damaged. This information may be needed when
ordering parts or requesting assistance.
Figure 2-2. Unit and Serial Number Locations
Altitude and Temperature Limitations
All units are subject to derating for altitude and
temperature; this will reduce the available power for
operating tools and accessories connected to the outlets.
Typical reductions in performance are 0.5% for every
1,000 ft (305 m) and 2-4% for every 1,000 ft (305 m) above
10,000 ft (3,048 m) of elevation, and 1% per 10 °F (5.6 °C)
increase in ambient air temperature over 72 °F (22 °C).
008083
B
A
14 Owner’s Manual for Mobile Generator
General Information
Component Locations
Exterior
Figure 2-3. Exterior Components
A Engine exhaust I Breaker panel access door
B Radiator access panel J Coolant and oil drain
C Unit lift point K Lug box access door
D Fuel fill port L Receptacle panel
E Side marker M Emergency stop switch
F Rear stabilizer mount N Tail light (2 locations)
G Tie-down point O Control panel access door
H Tongue jack
A
M
N
L
J
I
G
F
E
B
H
D
C
O
K
008881
Owner’s Manual for Mobile Generator 15
General Information
Connection Panel
Figure 2-4. Connection Panel Components
A Main circuit breaker I Ground connection lug
B Panel light J Connection lugs
C 50A circuit breaker (3 locations) K Cam lock receptacle (5 locations) (if equipped)
D Service lights switch L 120V/240V twist-lock outlets
E 20A circuit breaker (2 locations) M Connection for optional equipment Inlet
F Lug door safety switch N 120 V GFCI outlet (2 locations)
G Remote start terminal block O Connection for battery charger (if equipped)
H Neutral grounding bar P Emergency stop switch
01882
O
N
M
L
K
J
I
H
G
F
E
D
C
B
A
P
B
16 Owner’s Manual for Mobile Generator
General Information
Control Panel
Figure 2-5. Control Panel Components
A Genset controller F Generator lights switch
B Panel light G Engine speed switch
C Voltage selector switch H Controller power switch
D [not used] I Voltage adjustment dial (Potentiometer)
E Fuel transfer switch
C
E
F
H
G
A
B
008882
D
I
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Generac MMG35DF4 Owner's manual

Category
Power generators
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI