Anton/Bauer Interactive 2000 PowerCharger Owner's manual

Brand: Anton/Bauer

Model: Interactive 2000 PowerCharger

Type: Owner's manual

Anton/Bauer Interactive 2000 PowerCharger is a microprocessor-controlled battery charger designed to charge Anton/Bauer batteries and power Anton/Bauer battery-operated equipment. It features a two-line, 16-character LCD display that shows the charging status, battery voltage, and estimated time to full charge. The PowerCharger can be used to charge batteries in Anton/Bauer chargers, cameras, and other equipment. It can also be used to power Anton/Bauer battery-operated equipment directly.

One World. One Smart Choice.

™

Owner’s Manual

ULTRALIGHT® SYSTEM

A7595-0086 Rev N

( UL-S / UL-D)

Approved Copy

TABLE OF CONTENTS

1 INTRODUCTION

QUICK CHANGE HEAD MODULE

2 REMOVAL OF HEAD MODULE

3 PROPER BULB REMOVAL/REPLACEMENT

GOLD MOUNT

SNAP ON BATTERY BRACKET

4 ULTRALIGHT

FILTER ACCESSORIES

5-6 ULTRALIGHT

DIMMER ACCESSORIES

6 MOUNTING FILTERS

7 12V BULB SELECTION

30V BULB SELECTION

8 SPECIFICATION

SERVICE

9 LIMITED WARRANTY

Approved Copy

NEVER attempt to remove or install a bulb while Head Module is attached to the base or install a bulb directly into the socket/base assembly.

INTRODUCTION

The Ultralight

is an extremely compact, lightweight, portable lighting system with almost total versatility. Weighing only 13 ounces, the quick-

change feature permits instant eld light source changes without direct bulb handling, quickly adjusting to ood or spot lighting situations.

The Ultralight

will mount on a camera, light stand, or on a handle. With a simple bulb and cable change, the light can be adapted to operate

from the camera battery, a battery belt or from an AC supply. The Dual Base (UL-D) allows simultaneous mounting of two lights powered from

a single supply.

The quick-change Head Module tilts for indirect applications and can be easily tted with a swing-away wide angle adapter (UL-WA), diffuser (UL-

DF), or a dichroic lter (UL-DC). Spare bulbs are safely stored and carried in extra quick-change Head Modules, ready for immediate use. The

Head Module is faced with tempered safety glass both to protect the bulb capsule from foreign objects and to protect the user from hazardous

bulb malfunctions.

QUICK-CHANGE HEAD MODULE

The back of the quick-change Head Module (UL-HM) slides down over the pivoted socket housing. The lamp pins engage the socket contacts

and the module is held in place by the detent action of a screwhead which projects through a hole in the Head Module.

SWITCH

HEAD MODULE

4 Pin XLR for Power

Clamp Knob

Approved Copy

REMOVAL OF HEAD MODULE

IMPORTANT: The Head Module must be removed before attempting to change any bulb.

CAUTION: Head Module may be hot if the light has just been turned off.

For proper Head Module removal, follow these instructions.

1. Pivot the Head Module foward to disengage the recessed screw on the back of the Head Module (see Diagram A). Do not remove the

screw.

2. Release the Head Module from the base by pulling the Head Module straight up (see Diagram B).

DO NOT ATTEMPT TO REMOVE A BULB WHILE THE HEAD MODULE IS STILL ATTACHED TO THE BASE OF THE LIGHT.

Push Forward

Head Module

Light Base

Assembly

Lift Up

Diagram A Diagram B

Approved Copy

PROPER BULB REMOVAL /REPLACEMENT

For proper removal/replacement:

1. Follow the instructions on the previous page to remove the Head Module from the base of the light.

2. Using your thumbs, pull out on the hood tabs (see diagram) and rotate hood upwards.

3. Replace bulb and close hood of light ensuring that it ‘clicks’ back into place.

4. Reinstall Head Module onto light base.

CAUTION

- Do not touch the bulb capsule as contaminants from the nger can attack the glass and shorten the bulb life. Always hold the

bulb by the rim.

- Halogen bulbs are at greater than atmospheric pressure. To ensure operator safety, always close the hood before switching on

the light.

- Bulb voltage rating must match the power supply. Improper voltage may destroy or even explode the bulb capsule!

GOLD MOUNT SNAP ON BATTERY BRACKET

Every new Anton/Bauer

Gold Mount

Battery Bracket is equipped with a built-in PowerTap

auxiliary power output (fused).

By using a PowerTap

cable (appropriate lengths are available for all cameras and camcorders using Anton/Bauer brackets), the Anton/Bauer Snap On

battery can power the camera (or camcorder) and Ultralight

simultaneously.

If your Anton/Bauer battery bracket does not contain the PowerTap

connector, contact the Anton/Bauer Service Department at 1-800-541-1667.

A Gold Mount

upgrade program is available to convert Snap On or Snap On II

bracket(s) to the superior features of the Gold Mount

bracket

system.

Hood Tabs

Head Module Hood

Remove Bulb

Approved Copy

ULTRALIGHT

FILTER ACCESSORIES

Ultralight

adapter accessories are detachable pivoting lter/lenses allowing the user to ip the adapter in and out of the beam pattern. Adapters

(Diffuser, Wide Angle, Dichroic) are mounted in a holder, pivoted from a slotted tab into the space between the light head safety glass holder and

the hood.

UL-WA (Ultralight

Wide Angle Adapter): Converts both spot bulbs and medium ood bulbs into full ood (36) patterns. A very efcient optical

device that provides an exceptionally smoth and even pattern and will cover the widest angle zoom lenses. The UL-WA lter can also be used

with ood bulbs to smooth out uneven bulb patterns.

UL-DF (Ultralight

#1 Diffuser): For use with spot bulbs. Lowers light output by approximately one “f” stop (50%) while softening the edges

of the beam pattern.

UL-DC (Ultralight

Dichroic Filter): Converts output of bulbs to match 5500

K daylight. The UL-DC lter must be used when using the

Ultralight for daylight ll or cool white ourescent ll.

UL-BD (Ultralight

Barn Door Kit): Includes two hinged barn doors to t Ultralight

Adapters may be attached to the top of the Head Module or to either side and folded back against the Head Module when not in use. Two

adapters may be simultaneously attached to the lighthead (one on either side). A UL-DC can be used in combination with either a UL-WA or a

UL-DF simultaneously.

When trying to accommodate two lters at the same time, it may be necessary to obtain a new hinge for the lter which will allow simultaneous

mounting. The part number for this hinge is #5140-1051. Please contact the Anton/Bauer Customer Service Department at (800) 541-1667,

(203) 925-4991 or Email at support@antonbauer.com.

Top View of Head Module

Hinge

Closed

(In-Use)

UL-DC/UL-WA Filter

UL-DC Filter

Approved Copy

ULTRALIGHT

ACCESSORIES (AVAILABLE SEPARATELY)

ULTRALIGHT

DIMMER

The ULTRALIGHT

DIMMER (UL Dimmer) can be mounted on all camera/camcorders via either the Shoe Mount or ¼-20 Stud Mount. Note:

The UL2 that will be mounted on the UL Dimmer needs to have the ¼-20 Stud Mount installed. This is supplied with every UL2 light. Please

reference the UL2 Owners Manual.

SHOE MOUNT

1. Slide the UL Dimmer onto the Shoe Mount of the camera or camcorder.

2. Tighten down screw on top of UL Dimmer for secure t.

3. Screw UL2 light onto front of the UL Dimmer and plug the PowerTap

from the light into the UL Dimmer.

4. Plug the PowerTap

connector from the UL Dimmer into the Gold Mount on the rear of the camera.

Note: The UL Dimmer can only be used with the Anton/Bauer Gold Mount

and will not work with any camera-body PowerTap

connectors.

¼-20 STUD MOUNT

1. Remove Shoe Mount from the bottom of the UL Dimmer.

2. Align the UL Dimmer over the top of the ¼-20 thread on the camera handle.

3. Tighten down screw on top of UL Dimmer for secure t.

4. Screw UL2 light onto front of the UL Dimmer and plug the PowerTap

from the light into the UL Dimmer.

5. Plug the PowerTap

connector from the UL Dimmer into the Gold Mount

on the rear of the camera.

Note: The UL Dimmer can only be used with the Anton/Bauer Gold Mount

and will not work with any camera-body PowerTap

connectors.

ULTRALIGHT® DIMMER

This Ultralight

accessory allows the adjustment of light output from 0-100%. It’s microprocessor controlled PWM (Pulse-width modulation) cir-

cuit minimizes power loss and is designed for use with Ultralights

in the eld. With the push of a button, a low and high output setting can be

pre-programmed anywhere between 0-100%. With this feature, quick and exact light settings can be established before the shot, allowing for

quick light transitions without fumbling or the need to “dial-it-in”. Fitting underneath the light, its innovative bevel design provides for additional

down angle of the light while moving the light forward to avoid lens shadows. The UL Dimmer is fully compatible with the Automatique

feature

standard in most Gold Mounts

and has an auto shut off in the case of a low voltage battery.

Dimming Knob

Approved Copy

OPERATING INSTRUCTIONS

Adjusting the UL Dimmer:

- Use the dial to adjust the dimmer from 0 to 100%

- Turn clockwise toward 100%

- Turn counter clockwise toward 0%

Programming the Presets

To Reset:

- To Reset the preset, press & hold the dial inward for 4 seconds.

To Set Presets:

- To set a low preset, adjust light to the desired low end output and press the dial inward. Turning the dial completely counter clockwise will

bring the light precisely to this low preset.

- To set a high preset, adjust light to the desired high end output and press the dial inward. Turning the dial completely clockwise will bring

the light precisely to this high preset.

- Once a high and low preset is established, the UL Dimmer will only operate within that range.

- To set UL Dimmer for a single light output only, adjust light to the desired output and press the dial inward twice.

Note: The UltraDAYlight

(HMI Head Module) may be mounted on the dimmer as needed, but will not adjust with the dimmer and only operates

when the dimmer is set to 100% output.

MOUNTING OF FILTERS

For Temporary Mounting of Filter:

When properly tted, the slot in the tab will align with a screw in the center of the hood. The tab insertion requires a slight force. If the lter as-

sembly is too loose and does not stay in place, bend each side of the tab in opposite directions as shown to provide sufcient holding friction.

The friction on the lter pivot may be increased by tightening the pivot screw which extends the length of the lter assembly.

For Permanent Mounting of Filter:

First remove the screw and washer(between the hood and glass frame) from any one of the Head Module’s three sides Install the lter as de-

scribed above. Reinsert the screw and tighten fully. The washer will no longer be necessary.

Filter

Insert Filter

Remove Screw

and Washer

Approved Copy

12v BULB SELECTION

Bulbs used by the Ultralight

are Type MR16, tungsten-halogen bulbs. Spot or ood bulbs of any light distribution angle may be used. Low

Voltage Bulbs – 12 to 14.4 volts.

The Ultralight

offers the greatest versatility with the following low voltage bulbs. They can be powered from any 12-14.4 volt camera battery

with the PowerTap connector cable.

Triple Purpose Low Voltage Bulb

The ESX, EYR and EYF/FPA bulbs provide three beam/output options:

1. Spot (15º) - plain bulb.

2. Medium Spot (approximates 21º) - with Diffuser (UL-DF).

3. Flood (36º) - with Wide Angle adapter (UL-WA) which covers most zoom lenses in the extreme wide position.

Dual Purpose Low Voltage Bulb

The EXZ bulb provides two beam/output and is a good all around bulb:

1. Medium Food (24º) - plain bulb.

2. Full Flood (36º) - with Wide Angle Adapter (UL-WA).

Single Purpose Low Voltage Flood Only bulbs

The BAB, EYP, and EYC bulbs provide full ood (36º) - plain bulb.

Purpose/Type Bulb Code Watts Spot Med Flood Amps RunTime w/4 AH

Battery

Triple Purpose:

Spot/Med Spot

Flood

ESX

EYR

EYF

200

400

700

85*

170*

300*

30**

60**

120**

1-2/3

3-3/4

6-1/4

120 min

60 min

35 min

Dual Purpose:

Med Flood/Flood

EXZ 60 - - - - - 175 70 4-1/2 45 min

Single Purpose:

Flood Only

BAB

EYP

EYC

- - - - -

125

1-1/3

3-3/4

6-1/4

120 min

60 min

35 min

NOTE: All above data measured at 14 volts. * with a Diffuser (UL-DF) ** with a Wide Angle Adapter (UL-WA)

SPECIAL NOTE: Extensive eld testing indicates that the ESX bulb, despite its minimal 25 watts, when used with the UL-WA

Wide Angle Adapter, or the plain BAB bulb, provides the most pleasing lighting condition for most indoor

interviews in the typical 3 ft. to 6 ft. range

30v BULB SELECTION

While low voltage bulbs offer maximum versatility, the following bulbs can be used with 30 volt battery belt to provide excellent results in cer-

tain applications:

Bulb Watts Amps Footcandles

@ 5 feet

Run Time with 8 AH Battery

Belt

EXS 200 6-2/3 400 35 Min.

EKP/ENA 80 2-2/3 140 90 Min.

Note: The EKP/ENA bulb must be used with the UL-WA Wide Angle Adapter. The beam pattern of the plain bulb is unacceptable.

Approved Copy

SPECIFICATION

LAMPS Type MR-16

12-14 Volts, 25-85 Watts

MAX. CURRENT 8 amps; 200 Watts, 4-6 amp Typical for

Single Bulb

WEIGHT Single Base unit w/o bulb: 13 oz.

Dual Base unit w/o bulb: 19 oz.

SIZE Light Head Module: 2-1/4”W x

2-1/2”H x 2-13/16” DP

SERVICE

If you have any question about this or any Anton/Bauer product:

Please contact our Customer Support Department at 1-800-541-1667 (USA only) or 203-925-4991.

Approved Copy

LIMITED WARRANTY

This one (1) year limited warranty for the product specied in this

document (“Product”) is given by Anton/Bauer, Inc. (“Anton/Bauer”),

14 Progress Drive, Shelton, Connecticut 06484. If you (the purchaser

of the Product from Anton/Bauer, or the person for whom the Product

was purchased, if it was a gift) have any questions regarding Product

applications, Product specication, or to obtain warranty service on

this or any Anton/Bauer product, contact the company at the address

above.

THIS PRODUCT MUST BE REGISTERED WITH ANTON/BAUER

WITHIN 30 DAYS OF PURCHASE TO ASSURE WARRANTY

COVERAGE. TO REGISTER YOU MAY EITHER:

1. MAIL WARRANTY REGISTRATION CARD or

2. REGISTER ON LINE AT www.antonbauer.com

The liability of Anton/Bauer hereunder is expressly limited to a claim for

repair or replacement of the Product or as otherwise stated herein at

Anton/Bauer’s sole discretion. Notice of any claim under this warranty

shall be delivered to Anton/Bauer during the period of the warranty

and the Product shall be returned with its packaging promptly, at

your expense, to an Anton/Bauer Customer Support Center or to the

address above. Upon receipt of the Product and a record of your

compliance with the conditions of this warranty, Anton/Bauer will

repair or replace the Product and return it to you, or issue a credit, as

applicable. You are responsible for all shipping and handling charges

to and from authorized facility.

THIS WARRANTY DOES NOT APPLY TO AND IS VOID IN THE CASE OF

DEFECTS OR DAMAGE RESULTING FROM ACCIDENTS, DISASTER,

NEGLECT, MISUSE, IMPROPER INSTALLATION, IMPROPER OR

UNAUTHORIZED SERVICE OR MAINTENANCE, UNAUTHORIZED

REPLACEMENT PARTS OR ATTACHMENTS; OR DYSFUNCTION OR

MALFUNCTION OF, OR CAUSED BY, ANY OTHER PRODUCT OR

DEVICE. Misuse includes any use of the Product in other than

its intended application, including the use of this Product with

any charging device or accessory not manufactured by and/or

specied by Anton/Bauer. This warranty does not cover, and

Anton/Bauer assumes no responsibility for, any equipment or

devices used in conjunction with the Product.

ANTON/BAUER DISCLAIMS ANY LIABILITY FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR BREACH OF ANY WRITTEN

OR IMPLIED WARRANTY OF THE PRODUCT. UNDER NO

CIRCUMSTANCES WILL ANTON/BAUER BE RESPONSIBLE FOR

ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

This Warranty is to be construed and enforced in accordance with the

law of the State of Connecticut, including the provisions of the Uniform

Commercial Code as adopted and from time to time amended in the

State of Connecticut, and not the Convention for the International

Sale of Goods. This choice of Connecticut law is exclusive of any

Connecticut law that would require reliance on any law foreign to

Connecticut. Should any action of law or in equity be brought by any

person under this Warranty, such action shall be brought only in the

United States District Court for the District of Connecticut, or in any

Superior Court in Faireld County, Connecticut, USA. Some states do

not allow limitations on how long a warranty lasts, so the time period

limitation herein may not apply to you. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you. This warranty

gives you specic legal rights and you may have other legal rights

which may vary from state to state.

Use of unauthorized equipment in conjunction with Anton/Bauer

products constitutes misuse under our warranties and may limit or

void those warranties. Anton/Bauer does not authorize, condone,

recommend, or otherwise assume any liability or responsibility resulting

from the use of any battery, charger, or accessory made by Anton/Bauer

with any battery, charger or accessory not manufactured, produced or

sold by Anton/Bauer. Anton/Bauer only authorizes the use of original

Anton/Bauer products with this Product. Use only original Anton/Bauer

equipment with this Product.

Approved Copy

Anton/Bauer

A Vitec Group brand

The following are trademarks of Anton/Bauer, Inc.:

Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique,

DataTap, DIONIC, Elipz, Egripz, Elightz, Essentialz, Gold Mount, HubZ, HyTRON, Impac,

Interactive and design, LifeSaver, Logic Series, Logic Series Logo, Maxx man logo design,

Nexus, PowerStrap, Proformer, Probe, ProPac, RealTime, Satellight, Snap-On, Stasis, Stasis

Flex, Tandem, TrimPac, Ultrakit, Ultralight, “One World. One Smart Choice”, “The power

behind the best cameras capturing the best images in the world.”, “The quality standard

of the video industry”, “The worldwide standard”, and “There should always be choices. It

makes it easier to recognize the best.”

Lexan is a registered trademark of G.E. Company Corp.

Cordura is a registered trademark of E.I. duPont de Nemours

Anton/Bauer, Inc.

World Headquarters

14 Progress Drive, Shelton, CT U.S.A.

Tel (203) 929-1100 or (800) 541-1667

Fax (203) 929-9935

support@antonbauer.com

Anton/Bauer Europe, B.V.

Eurode Business Center, Eurode - Park 1-2

6461KB Kerkrade, The Netherlands

Tel (+31) 45 5639220

Fax (+31) 45 5639222

eurosupport@antonbauer.com

www.antonbauer.com

Anton/Bauer, Inc. - Signapore Oce

6 New Industrial Road, # 02-02 Hoe

Huat Ind. Bld., Singapore 536199

Tel (+65) 62975784

Fax (+65) 62825235

asia@antonbauer.com

Approved Copy

Anton/Bauer Interactive 2000 PowerCharger Owner's manual

Anton/Bauer Interactive 2000 PowerCharger Owner's manual

Anton/Bauer Interactive 2000 PowerCharger Owner's manual

Related papers

Other documents