Page is loading ...
Specifications
Design and specifications are subject to change without notice.
Physical Specifications
Product: Intermec lithium-ion battery pack (P/N 074201)
Dimensions: 5.3 cm x 5.3 cm x 1.5 cm (2.1 in x 2.1 in x 0.6 in)
Weight: 56.3 g (2 oz)
Capacity and Output Specifications
Maximum output: x 4.2 V
Mean output: x 3.7 V
Capacity: 2150 mAh
Temperature and Humidity Specifications
Operating temperature:
0°C to 50°C (32°F to 122°F)
Charging temperature:
0°C to 45°C (32°F to 113°F)
Storage temperature:
For up to 1 month
-20°C to 60°C (-4°F to 140°F)
For 1 to 3 months
-20°C to 45°C (-4°F to 113°F)
For 3 months to 1 year
-20°C to 25°C (-4°F to 77°F)
Relative humidity: 5% to 95% non-condensing
6001 36th Avenue West
Everett, WA 98203
U.S.A.
www.intermec.com
© 2004 Intermec Technologies Corp.
All Rights Reserved
CN2 Battery Instructions
*074754-001*
P/N 074754-001
CN2 Battery Instructions
The CN2 battery is a 2150 mAh lithium-ion battery (P/N
074201) designed for use in a CN2 Handheld Computer.
Replacing the Battery
1 To turn off the CN2, press and hold the Power key for about
2 seconds until the CN2 turns off.
2 Push down on the battery door latch, and pull up on the
battery door.
Battery
door
latch
3 Insert the stylus between the battery and the CN2 case, and
firmly press straight down until the battery is released.
4 Remove the battery.
5 Align the battery contacts, and insert the new battery in the
battery compartment. Press down on the battery until it clicks
into place.
Battery
6 Install the battery door.
Charging the Battery
If you just replaced the battery in the CN2, you need to fully
charge it before using the CN2. Batteries can be charged after
partial discharge without affecting the original battery capacity.
To charge the battery
• Place the CN2 in the CN2 Communications Dock (P/N
074248). A fully discharged battery charges in approximately
4 hours. For help, see the instructions that ship with the
communications dock.
Use only the methods described in these
instructions to recharge the Intermec battery
(P/N 074201). Recharging this battery with any
other charger could result in damage to the
battery.
Important Recommendations
• Charge the battery immediately before use or within a couple
of days of use.
• Do not short circuit the battery and keep it away from metallic
items.
• Do not disassemble, open, or modify the battery.
• Do not drop the battery or apply mechanical shocks or
pressure to it.
• Do not expose the battery to excessive heat or fire.
• Do not store the battery at temperatures above 60°C (140°F),
such as inside a car on a hot day or in direct sunlight, as this
may damage the battery.
• Do not immerse the battery in water or get the battery wet.
• Do not solder directly to the battery contacts.
• Use the Intermec battery (P/N 074201) only with a CN2. Use
of this battery in other devices could result in damage to the
device or battery.
• For maximum battery efficiency, the temperature range for
charging batteries is 0°C to 45°C (32°F to 113°F).
• Keep the battery contact holes clean and free of dust and dirt.
Remove any accumulated debris using the CN2 stylus.
• Do not recharge battery in locations that are extremely hot or
cold, dusty or dirty, very humid, or subject to vibration.
Disposal Instructions
When the battery reaches the end of its useful life, the
spent battery should be disposed of by a qualified recycler
or hazardous materials handler. If you are unsure of how
to properly dispose of this battery, contact your local
Intermec office for disposal information.
• Discarded batteries may create a safety hazard. Before disposal,
cover the battery contact terminals with electrical insulating tape.
• Keep away from children.
• Do not disassemble or dispose of in fire.
• Do not mix these batteries with the solid waste stream.
(Required in European countries.)
/
