Rosewill PB360-RGB AIO Closed Loop CPU Liquid Cooler User manual

Brand: Rosewill

Model: PB360-RGB AIO Closed Loop CPU Liquid Cooler

Type: User manual

Product Overview

Thank you for purchasing a Rosewill Liquid CPU Cooler.

Please read the instruction manual before use and retain for future reference.

PB360-RGB

Accessory Kit

* The apperance of product is subject to practicality.

Remote

Controller

Gasket

for Backplate

RGB Hub

Insulating Sheet

RGB Fan

LGA 2011

Screw

Thermal

Grease

Backplate

SATA Cable

3 Pin Connector

Cable

Stand-Off

Cylinder

Spring Screw

M3.5x31 Screw

for Backplate

x12

#6-32x6 Screw

for Radiator

x12

#6-32x29.5 Screw

for Fan

Intel Clip

(Pre-Installed)

AMD Clip

Liquid CPU Cooler

Installation Guide

1. Install the Fan and

Radiator into PC Case

1-1. Secure fans on radiator with

twelve #6-32x29.5 mm screws

(Figure 1).

1-2. Secure installed radiator in the

case with twelve #6-32x6 mm

screws.

2. Instructions for LGA 2066

and 2011

2-1. Conrm the motherboard is LGA

2066 / 2011 platform (Figure 2).

2-2. Secure four LGA 2011 screws into

the corresponding screw holes.

2-3. Apply a proper amount of the

thermal grease on CPU.

2-4. Tear the protector off from the

bottom of water block and place

the installed water block steady

with buckle and LGA 2011 screws

on the cut-out of the motherboard.

2-5. Keep the copper bass plate

touching the CPU as much as

possible and secure water block

temperately on top of LGA 2066 /

2011 with four screws.

3. Instructions for AMD

Water Block

3-1. Uninstall the Intel Clip and nd the

correct AMD buckle as shown in

gure (Figure 3).

3-2. Push buckles straight through the

cut-out to bottom.

#6-32x29.5

Fan Screws

#6-32x6

Radiator Screws

Spring Screws

LGA 2011 Screws

CPU

Motherboard

Buckie

Cut-Out

AMD Clip

* The apperance of product is

subject to practicality.

4. Instructions for AMD / Intel

4-1. Conrm the motherboard and match the correct side of backplate (AMD / Intel) (Figure 4).

4-2. Find the screw holes and secure four M3.5x31 screws in. Please note the scramble of

dummy-proof between stand-off and M3.5x31 screws.

4-3. Insert the installed backplate on the back of the motherboard and secure the stand-off

from the other side.

4-4. Apply a proper amount of the thermal grease on CPU.

4-5. Tear the protector off from the bottom of the water block and place the installed water

block steady with buckle and M3.5x31 screws on the cut-out of motherboard.

4-6. Keep the copper bass plate touching the CPU as much as possible and secure water block

temperately on top of M3.5x31 screws with four spring screws.

5. Connect Power to the Water Pump

Activate water cooler by plugging the conducting

wire into the consistent CPU_FAN or CPU_OPT pin

header (Figure 5).

AMD Intel

Spring Screws

AMD / Intel Clip

Stand-Off Cylinder

CPU

Motherboard

Insulating Sheet

Backplate Gasket

Backplate

M3.5 x 31

Backplate Screw

Dummy-ProofDummy-Proof

CPU_FAN

Technical Support Information [email protected] 1-800-575-9885

Please register your product at www.rosewill.com for complete warranty information and support for your product.

PB360-RGB_A

6. Connect the RGB Hub

6-1. Connect the fan cable and water block cable into the RGB fan hub slot labeled “Fans”.

6-2. Plug the 3-pin connector cable to the addressable 5V* RGB header of your motherboard

and other end to M/IN on hub as another control option for system synchronization.

6-3. Connect the power cable to the RGB fan hub and connect the other end to your power

supply.

6-4. Mount the RGB fan hub to a desired location within the system via the magnet attached on

the back of the RGB fan hub (Figure 6).

7. Remote Control

To switch remote controller to

motherboard synchronization,

press the remote control’s “ON”

button. Press “ON” again to

return back to remote control

(Figure 7).

Power

Supply

M/B

Addressable

RGB Header

Switch On Between Remote

Control and Motherboard Control

Programmed Lighting Effects

Single Color Options

Low / Medium / High Fan Speed

LED Switch Off

Increase Brightness / Decrease

Brightness / Cycle Through Single

Color Options

Caution

To avoid damage during installation, connect the case fan to the included fan hub only.

Do not connect fans directly to any motherboard.

*12V RGB headers are not supported

Rosewill PB360-RGB AIO Closed Loop CPU Liquid Cooler User manual

Rosewill PB360-RGB AIO Closed Loop CPU Liquid Cooler User manual

Rosewill PB360-RGB AIO Closed Loop CPU Liquid Cooler User manual

Related papers

Other documents