Page is loading ...
Quick User Guide
PB240-RGB
RGB Advanced Liquid CPU Cooler
• Product Overview ................................................ 02
• Installation Guide
1. Install the Fan and Radiator into PC Case ....... 03
2. Instructions for LGA 2066 and 2011 ................
3. Instructions for AMD Water Block ...................
4. Instructions for AMD / Intel ..............................
5.
Connect Power to the Water Pump
..................
6. Connect the RGB Hub .....................................
7. Remote Control ................................................ 09
8. Caution ............................................................. 09
Thank you for purchasing a Rosewill Liquid CPU Cooler.
Please read the instruction manual before use and retain
for future reference.
The product images used are for illustration purposes only
and may vary from the actual product.
1
Table of Contents
04
08
05
07
06
2 3
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
Product Overview Installation Guide
1. Install the Fan and Radiator into PC Case
1-1 Secure fans on radiator with eight #6-32x29.5 mm screws.
1-2 Secure installed radiator in the case with eight #6-32x6 mm screws.
Backplate x 1
LGA 2011 Screw x 4
#6-32x6 Screw x 8
for Radiator
Gasket x 4 for Backplate
Liquid CPU Cooler x 1
Spring Screw x 4
Thermal Grease x 1
#6-32x29.5 Screw x 8
for Fan
Insulating Sheet x 1
Intel Clip x 1
(Pre-Installed)
AMD Clip x 1
M3.5x31 Screw x 4
for Backplate
SATA Cable x 1
3 Pin Connector
Cable x 1
RGB Hub x1
RGB Fan x 2
Remote Control x 1
Stand-Off Cylinder x 4
1
3
5
7
11
2
4
6
8
10
12
9
15
13
14
18
16
17
#6-32x6
Radiator Screws
#6-32x29.5
Fan Screws
4 5
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
Installation Guide
2. Instructions for LGA 2066 and 2011
2-1 Confirm the motherboard is LGA 2066 / 2011 platform.
2-2 Secure four LGA 2011 screws into the corresponding screw holes.
2-3 Apply a proper amount of the thermal grease on CPU.
2-4 Tear the protector off from the bottom of water block and place the installed water
block steady with buckle and LGA 2011 screws on the cut-out of the motherboard.
2-5 Keep the copper bass plate touching the CPU as much as possible and secure
water block temperately on top of LGA 2066 / 2011 with four screws.
Spring Screws
LGA 2011 Screws
CPU
Motherboard
Installation Guide
3. Instructions for AMD Water Block
3-1 Uninstall the Intel Clip and find the correct AMD buckle as shown in figure.
3-2 Push buckles straight through the cut-out to bottom.
Buckie Cut-Out
AMD Clip
6 7
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
Installation Guide
4. Instructions for AMD / Intel
4-1 Confirm the motherboard and match the correct side of backplate (AMD / Intel).
4-2 Find the screw holes and secure four M3.5x31 screws in. Please note the scramble
of dummy-proof between stand-off and M3.5x31 screws.
4-3 Insert the installed backplate on the back of the motherboard and secure the stand-off
from the other side.
4-4 Apply a proper amount of the thermal grease on CPU.
4-5 Tear the protector off from the bottom of the water block and place the installed water
block steady with buckle and M3.5x31 screws on the cut-out of motherboard.
4-6 Keep the copper bass plate touching the CPU as much as possible and secure water
block temperately on top of M3.5x31 screws with four spring screws.
Installation Guide
5. Connect Power to the Water Pump
Activate water cooler by plugging the conducting wire into the consistent CPU_FAN
or WCPU_OPT pin header.
CPU_FAN
AMD
Intel
Spring Screws
Stand-Off Cylinder
CPU
Motherboard
Backplate Gasket
AMD / Intel Clip
Backplate Screw
Backplate
Insulating Sheet
Dummy-Proof
Dummy-Proof
8 9
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
RGB Advanced
Liquid CPU Cooler
PB240-RGB Quick User Guide
Installation Guide
6. Connect the RGB Hub
6-1 Connect the fan cable and water block cable into the RGB fan hub slot labeled “Fans”.
6-2 Plug the 3-pin connector cable to the addressable 5V* RGB header of your
motherboard and other end to M/IN on hub as another control option for system
synchronization.
6-3 Connect the power cable to the RGB fan hub and connect the other end to your
power supply.
6-4 Mount the RGB fan hub to a desired location within the system via the magnet
attached on the back of the RGB fan hub.
Installation Guide
7. Remote Control
To switch remote controller to motherboard synchronization, press the remote control’s
“ON” button. Press “ON” again to return back to remote control.
LED Switch Off
Increase Brightness / Decrease
Brightness / Cycle Through Single
Color Options
Switch On Between Remote Control
and Motherboard Control
Programmed Lighting Effects
Single Color Options
Low / Medium / High Fan Speed
CAUTION
To avoid damage during installation, connect the case fans to the included fan hub only.
Do not connect fans directly to any motherboard.
*12V RGB headers are not supported
Power
Supply
M/B
Addressable
RGB Header
Technical Support Information
[email protected] 1-800-575-9885
----------------------------------------------------------------------------------
Thank you for purchasing a quality Rosewill product.
Please register your product at www.rosewill.com
for complete warranty information and support for your product.
PB240-RGB_A
/