Art-Tech P-51D Gunfighter User manual

Brand: Art-Tech

Model: P-51D Gunfighter

Category: Toys & accessories

Type: User manual

Art-Tech P-51D Gunfighter is a three-channel RC airplane suitable for beginners, intermediate, and experienced hobbyists. It features a durable EPO foam construction, high-speed performance, and excellent flight stability. With a 965mm wingspan, 790mm length, and a flying weight of 700g, this model is equipped with a brushless outrunner motor, a 20A brushless ESC, 4X 9g high-speed micro servos, and an 11.1V 1300mAh Li-Polymer battery. The 2.4GHz radio control system provides a range of 400 meters.

Instruction manual

www.art-tech.com

Statement: Specifications may change without notice, please refer to the real one for configuration. 2010.11

声明：产品以实物为准，若有更改，恕不另行通知. 2010.11

★中文部分

★Product introduction

★Main specification

★Safety precautions!

★Charge Mode and Warning

★Safety Instruction of Li-Po Battery

★Assembling steps for P-51D

★Transmitter Features

★Binding process for DSSS 2.4 GHZ R/C system

★

★Trouble shooting

★Spare parts list

Operating Manual for the radio control system

Center of Gravity Check

www.motionrc.com

Product introduction

Wingspan: 965mm (38 inch)

Length: 790mm (31 inch)

Flying Weight: 700g (24.7 oz)

Motor: Brushless Outrunner C4038-15

Speed Controller: 20A Brushless ESC

Servo: 4X 9g high speed micro servos

Battery: 11.1V 1300mah Li-Polymer

Control system: 4 CH EFLY-4BII 2.4GHz

Radio Control Range: 400m

Thank you for purchasing “P-51D Gunfighter” Radio Controlled Model Airplane. This

model uses EPO style foam, which makes the model incredibly strong and durable even in a

crash. It is easy to control, with excellent flight performance in high-speed, superior flight

stability. This model adopts 3 channel control mode, with simple structure, easy ,

with high scale, vivid appearance, and luxuriant paintings. This is the best model for

beginner, intermediate and experienced hobby enthusiast. We hope it will bring you more

fun while flying.

maintainance

1. This model is not a toy , and it is for intermediate and experienced hobby

enthusiast.

2. Please pay much attention to the warning information in this manual.

3. It is highly recommended to fly this model under guidance from an experienced model

pilot if you are a novice/beginner.

4.A crash can happen if the model is not flown according to these instructions and if the

pilot is not experienced enough.

5.To gain the most from this model you need to improve step by step from basic training

up to perfect flight before moving onto aerobatics.

beginner,

Main specification

Safety warning

www.motionrc.com

Safety precautions!

Flammables

4\5

1) The model is not suitable to fly in the places listed below, in a crowd of

people, around telegraph or electrical poles, around cars, near to traffic

or next to a full size air field/airport.

2) Do not fly in bad weather or in high winds, the lower the wind the better

the model will fly.

3) Never attempt to catch the aircraft in your hands as this could lead to

serious injury.

4) This model is recommended for people over the age of 12 and with

experience, if under this age or a novice then we recommend you get

tuition from an experienced model pilot.

5) Always unplug the flight battery when you finish flying the aircraft.

6) Please always keep clear of the propeller when you connect the flight

battery, the transmitter must be switch on all the time the flight battery is

connected.

7) Please remember to turn on the transmitter first before flying and keep

away from the propeller when the flight battery is connected.

8) Please disconnect the flight battery before switching of the transmitter

when you have finished your flight. Not following this strict procedure can

result in an out of controlled model.

9) Do not charge in or on a wet surface. Please pay attention to the

charger while on charge, the maximum time that the battery should be left

on charge is four hours. It is normal for the battery to get warm during use

but not HOT.

10) Never charge on a flammable base such as carpet etc, we recommend

that you charge on a concrete floor or a metal tea tray. When charged

disconnect the battery from the charger and the charger from the wall

socket. Always supervise the battery when charging, do not leave it on its

own to charge just in case of a problem.

www.motionrc.com

Charge Mode and Warning

Li-Po battery(balance changer)

ATI-0910 Li-poly battery balance charger using instruction

Specifications:

Input voltage: DC 10V~15V

Output voltage: DC 7.4V&11.1V

Charge current: 0.3A~1.2A

Indicator state:

LED light near to the battery plug turns red:

the charger have connected the power supply.

LED light near to the DC port turns red: under charging

LED light near to the DC port turns green: full charged

LED light near to the DC port extinuishs: no charging

Separated battery detection: The voltage of any battery reaches

4.2V, the charge of it will cease automatically.

Using method:

1. Connect the mans adaptor to the charger as per the above image.

2. Connect the adaptor to the 240v supply, the LED should turn red indicating that it is ready to

charge.

3. Connect the battery to the charger per its interface mark. The LED becomes red, which means

the battery is on the way.

4. The LED turns green when fully charged ( if the light is not green after four hours remove from

charge and use any way ) and then the battery is ready to be used.

Notice

1. Do not insert any conductive into the cooling hole when power is on, or damage will be caused

to the charger.

2. While charging is in process, please do not place it near flammable materials.

3. Expect Li poly battery, this charger is not allowed for other kinds of battery.

4. While charging, please keep it out of the reach of Children.

5. When this charger is in use, please do not go away and leave it unwatched, if any abnormality

occurs (such as the power indicator is off, the temperature of the battery rise rapidly, etc.) stop

charging immediately.

6. Please do not use power with output voltage higher than 18V.

7. Please do not disassemble the charger or its accessories.

8. When the battery is not cool down, please do not urge to charge it.

www.motionrc.com

Safety Instruction of Li-Po Battery

01.Do not disassemble or reconstruct the battery.

02.Do not short-circuit the battery.

03.Do not use or leave the battery nearby the fire, stove or heated place.

04.Do not immerse the battery in water or sea water, do not get it wet.

05.Do not charge the battery nearby the fire or under the blazing sunlight.

06.Do not drive a nail into the battery, strike it by hammer or tread on it.

07.Do not impact or throw the battery.

08.Do not use the battery with conspicuous damage or deformation.

09.Do not make the direct soldering on the battery.

10.Do not reverse charge or over discharge the battery.

11.Do not reverse charge or reverse connect.

12.Do not connect the battery to the ordinary charger socket or car cigarette jack.

13.Do not use the battery for unspecified equipment.

15.Do not mix the Li-Poly battery with other un-chargeable battery .

16.Do not continue charging the battery over the prescribed time.

17.Do not put the battery into the microwave oven or high-pressure container.

18.Do not use the abnormal battery.

19.Do not use or keep the battery under the sunlight.

20.Do not use the battery nearby the place where generates static electricity (over 64V).

21.Do not charge the battery when the environmental temperature is under 0℃ or over 45℃.

22.If you find the battery leaking, smelling or abnormal, stop using it .

23.Keep the battery away from the children.

24.Use the specified charger and observe charging requirement (under 1.5A).

25.When using by minors, parents should show them the correct way to charge.

14.Do not touch the leaking battery directly, please wash your skin or clothes with water

if they are bedewed by liquid leaking from the battery.

1. Use the original charger. Never charge the battery at more than 1.5 A.

2. Never discharge the battery at more than 5C. Do not discharge too long as this will

damage the battery.

3. For full flight time to be achieved please cycle the cells through three flights.

4. Never charge the battery on a carpet floor, this can cause a fire!

5. In order to maintain the voltage and ensure the life time of the battery, please

recharge it if it has not been used for more than three months.

Caution

www.motionrc.com

1、Install the landing gear to the main wing's groove in right direction.

2、Connect the servo wire from main wing to the first channel of receiver.

3、Fix the main wing set to the fuselage properly.

Assembling steps for P-51

www.motionrc.com

4、Penetrate the screw from main wing into fuselage and fix it.

5、Place the horizontal into place and attach with screws.stabil i zer

￠4X30MM

………… 2

￠2X12MM

………… 2

www.motionrc.com

6、Install the vertical stab in place.

7、Install and attach the tail fairings with screws.

￠1.7X6MM ￠1.7X33MM

………… 2 ………… 1

www.motionrc.com

8、connect the clevis to the rudder and elevator.

9、Place spinner hub on shaft then the propeller and then the nut. Then snap spinner in

place. Make sure the transmitter batteries are charged, the transmitter is off and the

throttle is at idle. Now turn on transmitter.

￠1.7X16MM

………… 1

www.motionrc.com

10、Plug well charged battery to the transmitter and close the battery bay.

11、Please put the socket into the fuselage body,then cover the battery.

12、Before using, please test function of all joysticks. While testing motor, make sure the

propeller is out of reach of any person or item and then fix the plane.

www.motionrc.com

4 channel full-scale 2.4GHZ RC device. It adopts the technology of direct sequence spread

spectrum (DSSS) t o have good anti-interference, stability and reliability.

It can be used for all ordinary aeroplanes, gliders models, and so on.

It has simulator signal interface. low voltage alarm.

Transmitter particular introduce

Configured with 2.4G radio control system with a ground distance

of 200meters and Air distance of 400 meters.

(Mode 2)

Trim

Hook

Charger port

Servo reverse

Elevator down

Rudder

left

Rudder

right

Elevator up

Power switch

Power indicator

Throttle Max

Aileron

left

Aileron

right

Throttle Min

Antenna

Carrying bar

Frequency Switch

Features remote control device transmitter

www.motionrc.com

The process of frequency bind for DSSS series 2.4GHz R/C system

1. plug the short- circuit plug into the Receiver

in the position of BATT. Connect the ESC to

receiver for electricity supply, which results to

the indicator light glitters.

2. Press the frequency bind button, then

turn on the transmitter' s power.

6. The indicator light turns bright again,

which means that the radio system can

work normally now.

3. the indicator light of the receiver will light,

which indicates that the frequency bind is

successful.

4. Unplug the short-circuit, the indicator

light glitters.

5. Press frequency bind button again to get it

rebound. After the indicator light flashes for a

few seconds, it turns green, the transmitter

get into working mode.

Place the transmitter and the receiver close to each other within one (1) meter.

Please do not press the frequency bind switch when the Transmitter at work mode, or else your device will not work!

www.motionrc.com

Valuable experience

1. If you have a simulator we recommend that you practice with it before you fly your J-3. This will be very

helpful for your first flight.

2. Check and make sure all the control surfaces work normally and move towards the right direction before

flying.

3. We recommend that you take the model up to a height of around 100m and then cruise at around 1/3

power. This will be helpful for ou to get familiar with the performance.

4. Users should control the airplane gently to reduce the risk of crash, and to prolong the working time of

the airplane.

5. The turning radius should not be too tight or the aircraft could become out of control very quickly which

could result in an incident that you did not intend.

6. Please make sure to take off into the wind. The beginners had better fly in breeze and up wing area.

Operating Manual for the radio control system

Components to the R/C system

a transmitter, a receiver, a servo, a speed controller

The sketch map for connecting the receiver:

RECEIVER

ER61-2.4GHz

RECEIVER

ER61-2.4GHz

Signal

(White line)

(Red line)

(Black line)

Left aileron

servo

Right aileron

servo

Motor

Battery

ESC

Elevator servo

Rudder servo

www.motionrc.com

Problem Cause Solution

Motor does not run

1. Battery is not fully charged.

2. The battery of transmitter is

not sufficient

3. Check the wire connection

inside the model

4. The motor do not work due to

impact or damage.

5. The frequency binding of the

radio system fails

1. Charge the batteries.

2. Install a full charged battery

3. If any problem, please contact

your dealer

4. Change a new motor

5. Please do the frequency

binding again according to the

page 13.

No reaction of the

control surface

properly or inverted plug.

2.The servo is damaged

The servo cable didn’t plug 1. Check the connection of

the servo cable

2.Change another servo.

Can not fly straight

1.The rudder is not in the center

position of the airframe

2.The main wing is not fixed in

the center position of the airframe.

1. Adjust the trim switch on

the transmitter

2.Re-assembly the main wing

Can not climb 1. The battery is not fully charged.

2. Two aileron are biased downward

1. Charger the battery

2. Adjust the inching switch on

the Transmitter.

Limited control range The batteries are almost flat Install new batteries

Trouble shooting

1 1

10 / inch~11 / inch

2 2

Please check the CG before heading to

the flying fileld.The center of gravity for your

P-51D should fall within the range

as indicated by the arrows.For your initial

flights,we suggest that you balance the

model toward the front fo the wing.After you

become more familiar with the airplane,you

can move the CG more aft.However,under

no circumstances should the CG fall

behind(toward the rudder) the rear mark.If

necessary, adjust the CG by moving your

receiver or adding weight to the nose or tail

Gunfighter

of the airplane.

Center of Gravity Check

www.motionrc.com

Spare parts list

No:5B201

Main wing set

No:5B141

Propeller

No:5B221

Small plastic set

No:5B211

Tail wing set

No:5B191

Fuselage

No:5B051

Main landing gear set

No:41411

Li-poly battery

(11.1V-1300mAh)

No:33012

Brushless ESC(20A)

No:3A01C

Brushless motor

(C4038-15)

www.motionrc.com

深圳市艾特航模股份有限公司

Art-Tech P-51D Gunfighter User manual

Brand: Art-Tech

Model: P-51D Gunfighter

Category: Toys & accessories

Type: User manual

Download PDF

report

Art-Tech P-51D Gunfighter User manual

Art-Tech P-51D Gunfighter User manual

Related papers

Other documents