Aeromax 40 Easy Stik ARF Assembly Instructions Manual

Brand: Aeromax

Model: 40 Easy Stik ARF

Type: Assembly Instructions Manual

Aeromax 40 Easy Stik ARF is a radio-controlled aircraft with a 1470mm wingspan and a weight of 2200g. It is designed for use with a .40~.52 2S engine and has a suggested C.G. of 75mm. The aircraft comes with a number of features that make it easy to assemble and fly, including a pre-assembled main wing with slight dihedral, aileron and elevator servos, and a main landing gear. With its easy-to-follow assembly instructions, the Aeromax 40 Easy Stik ARF is a great choice for beginner and experienced RC pilots alike.

Aeromax 40 Easy Stik ARF is a radio-controlled aircraft with a 1470mm wingspan and a weight of 2200g. It is designed for use with a .40~.52 2S engine and has a suggested C.G. of 75mm. The aircraft comes with a number of features that make it easy to assemble and fly, including a pre-assembled main wing with slight dihedral, aileron and elevator servos, and a main landing gear. With its easy-to-follow assembly instructions, the Aeromax 40 Easy Stik ARF is a great choice for beginner and experienced RC pilots alike.

Assembly Instructions

Wing Span 1470mm

Wing Area 36 sq.dm

Length 1050mm

Weight 2200g

Engine .40~.52 2S

Before Beginning assembly, please read these

instructions thoroughly.

Radio -Controlle d AircraftRadio -Controlle d Aircraft

This radio control model is not a toy!

40 Easy Stik ARF 40 ARF

Parts of the airplane

Accessories

1.Main Wing

1

4

The main wing has slight dihedral.

Ensure that the two wing halves are

securely glued together with epoxy.

确保粘牢

在此处钻孔，方便胶水流入

Create small opening here

to allow glue to seep through.

2.Aileron Servo

2

用笔在这里做个记号

Measure the position of

the wire that aligns with

your servo arm.You will

bend the wire at this

position.

2.Aileron Servo

用胶带加固

You may use tape to further secure

the clevis.

The clevis needs to be

secured onto the pushrod

for about 8mm (3/8 in)

拧进去8mm左右

Bend the end of the wire into a right

angle.Depending on the length of

the wire needed, excess wire can be

removed

弯成9 0度并剪去多余的钢丝

Servo Setup

Servo and screws needs to

be purchased separately.

2mmX15mm

2

Screw

3.Stabilizer &Elevator

将平尾粘到机身上.

You should make sure both the rudder

and the elevator are properly centered

with the fuselage.

3

Glue the horizontal stabilizer to

the fuselage

4

3mmX18mm

4.Main Landing Gear

3

5. Nose landing gear

Screw

尾撬

5

degrees by the user

The wire needs to be bent 90

照前面的方法安装方向舵机

Using the same procedure as previously,

to install this servo and pushrod.

6.Stabilizer &

Elevator Servo

2mmX18mm

2

Screw

6

7.Engine

3

4mmX30mm Screw

3mmX30mm

Screw

8.Throttle Servo

Engine needs to be purchased

separately.

发动机另购

9.Fuel Tank

AIR

To Engine

Pumpi ng fuel

7

10. Fuselage Setup

11. Main Wing

Wing Setting

接收机和电池另购

Receiver and battery need to be

purchased separately.

Suggested C.G.

75mm

The suggested C.G. is only

a starting point for your

setup process. You should

reposition the receiver and

battery until you achieved

the desired balance.

1
2
3
4
5
6
7
8
9
10
11
12

Aeromax 40 Easy Stik ARF Assembly Instructions Manual

Brand: Aeromax

Model: 40 Easy Stik ARF

Type: Assembly Instructions Manual

Aeromax 40 Easy Stik ARF is a radio-controlled aircraft with a 1470mm wingspan and a weight of 2200g. It is designed for use with a .40~.52 2S engine and has a suggested C.G. of 75mm. The aircraft comes with a number of features that make it easy to assemble and fly, including a pre-assembled main wing with slight dihedral, aileron and elevator servos, and a main landing gear. With its easy-to-follow assembly instructions, the Aeromax 40 Easy Stik ARF is a great choice for beginner and experienced RC pilots alike.

Download PDF

Other documents