Allen + Roth JJ-LARGE SB GNT COMP Installation guide

Brand: Allen + Roth

Model: JJ-LARGE SB GNT COMP

Type: Installation guide

This manual is also suitable for

allen roth Granite Kitchen Sink

lowes.com/allenandroth

Granite Kitchen Sink

ITEM #2889548 Single Bowl

#2889547 Double Bowl

MODEL# JJ-LARGE SB GNT COMP Single Bowl

JJ-DB GNT COMP Double Bowl

Serial Number Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer service

department at 1-866-439-9800,

8 a.m. - 8 p.m., EST, Monday - Sunday. You could also contact us at

[email protected] or visit www.lowespartsplus.com.

ATTACH YOUR RECEIPT HERE

Español p. 9

Allen & Roth and logo design are

trademarks or registered trademarks

SM20575

welcoming • sophisticated • inspiring

lowes.com/allenandroth

PACKAGE CONTENTS

0.31"

0.2"

R0.39"

R1.1"

0.39"

Double Bowl Topmount Cut-out

Double Bowl Undermount Cut-out

21.21"21.21"

32.21"32.21"

30.94"

17.01"17.01"

0.16"

R0.5"

0.37"

Single Bowl Topmount Cut-out

Single Bowl Undermount Cut-out

21.25"21.25"

32.25"32.25"

30.81"

16.81"16.81"

R0.91

PART DESCRIPTION QUANTITY

A Double Bowl Sink 1

B 2-in-1 Template 1

PART DESCRIPTION QUANTITY

A Single Bowl Sink 1

B 2-in-1 Template 1

lowes.com/allenandroth

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install this

product.

WARNING

• Keep all packaging materials out of the reach of children to prevent possible choking or suffocation.

• Use caution when installing the sink. There is a risk of crushing your ngers when inserting the sink

into the installation location.

CAUTION

• NEVER place hot objects such as hot pans on the sink. Wait until the object has cooled or use a

heat resistant plate when placing hot objects on the sink surface.

NOTICE

• Avoid leaving wet sponges, salt, and corrosive substances on the sink for long periods of time. Lines

and scratches may be caused by improper use of the sink.

• DO NOT place the sink on its side as there is a risk of damage.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

HARDWARE CONTENTS

Top-mount Clip

with Screw

Qty. 8

Mounting Bracket

Qty. 8

Mounting Screw

Qty. 8

Threaded nut

Qty. 8

PREPARATION

Before beginning installation of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to install

the product.

Estimated Installation Time: 30 minutes.

Tools Required for Installation (not included): jigsaw, silicone sealant, phillips screwdriver, hammer,

athead screwdriver, tungsten rasp, safety goggles, pencil.

BB CC DD

lowes.com/allenandroth

INSTALLATION INSTRUCTIONS–TOPMOUNT

2. Preparing the sink for installation

* Please skip this step unless additional

holes are necessary for your faucet and/or

accessories.

Gently place sink into countertop cut out to

support the outer ledge of your sink. With a

athead screwdriver and hammer, proceed to

punch out holes.

Finish the hole with a small tungsten rasp and

remove the stickers on the sink for any

pre-marked holes not needed.

Note: A round sticker on the sink indicates

where the knock-out holes have been prepared.

Check that this sticker has not been moved.

Also note that one hole has already been

prepared.

CAUTION

• DO NOT turn the sink over in order to push

out the pre-scored hole on the sink. This will

damage the sink. Punch out the pre-scored

hole as shown.

1. Preparing the installation location

If necessary, disconnect the water supply lines

underneath the sink and remove the old sink.

Place the 2-in-1 template (B) on sink installation

location. Using a pencil, mark the correct location

(see insets on page 2) onto the sink.

Using a jigsaw, cut out the location for the sink.

lowes.com/allenandroth

INSTALLATION INSTRUCTIONS–TOPMOUNT

3. Installing the mounting brackets

Turn the sink over and press the mounting clips

(AA) into the pre-drilled holes along the rim of

the sink (A) until they are ush on the base of

the sink (A).

Hammer in the spreader bolts on both sides of

the mounting clips (AA) as far as the stop, using

either a screwdriver or hammer.

Apply silicone sealant (not included) along the

edge of the sink (A).

4. Installing the sink

Place the sink (A) into the countertop and

remove any excess sealant that comes out from

the edges.

Tighten the screws on the mounting clips (AA)

underneath the sink to anchor the sink (A).

Hardware Used

Topmount Clip

with Screw

x 8

lowes.com/allenandroth

2. Preparing to mount the sink

From underneath the countertop, prepare

30 mm holes around the perimeter of the

installation location. A typical installation will

have two holes at each corner of the sink.

Place the threaded nuts (DD) securely into each

of the holes underneath the counter.

1. Preparing the installation location

If necessary, disconnect the water supply lines

underneath the sink and remove the old sink.

Using a pencil mark the measurements (from the

insets on page 2) onto the sink location.

Using a jigsaw, cut out the location for the sink.

INSTALLATION INSTRUCTIONS–UNDERMOUNT

Hardware Used

Threaded Nut

x 8

lowes.com/allenandroth

3. Mounting the sink

From underneath the countertop, apply silicone

sealant around the perimeter of the installation

location.

Place the sink (A) underneath the countertop

by inserting mounting screws (BB) through the

mounting brackets (CC) and into the installed

threaded nuts (DD).

Tighten the screws in a crisscross pattern

to ensure that the sink is installed evenly

underneath the counter.

INSTALLATION INSTRUCTIONS–UNDERMOUNT

Hardware Used

Mounting

Bracket

x 8

Hardware Used

Mounting

Screw

x 8

Allen + Roth JJ-LARGE SB GNT COMP Installation guide

Brand: Allen + Roth

Model: JJ-LARGE SB GNT COMP

Type: Installation guide

This manual is also suitable for

allen roth Granite Kitchen Sink

Download PDF

report

Allen + Roth JJ-LARGE SB GNT COMP Installation guide

This manual is also suitable for

Allen + Roth JJ-LARGE SB GNT COMP Installation guide

Related papers

Other documents