Verona VEFSGE 304 SC User manual

GAS/ELECTRIC RANGE

for residential use only

THIS RANGE IS FOR RESIDENTIAL USE ONLY

FOR INSTALLER ONLY

Some models are supplied with a protective lm on steel and aluminium

parts. This lm must be removed before installing/using the appliance.

Models: VEFSGE 304 SC..

INSTALLATION INSTRUCTIONS

IMPORTANT - PLEASE READ AND FOLLOW

• Beforebeginning,pleasereadtheseinstructionscompletelyandcarefully.

• Donotremovepermanentlyafxedlabels,warnings,orplatesfromtheproduct.Thismay

voidthewarranty.

• Pleaseobservealllocalandnationalcodesandordinances.

• Pleaseensurethatthisproductisproperlygrounded.

• The installer should leave these instructions with the consumer who should retain

for local inspector’s use and for future reference.

Installationmustconformwithlocalcodesorintheabsenceofcodes,theNationalFuelGas

CodeANSIZ223.1/NFPA54-Iatestedition.Electricalinstallationmustbeinaccordancewith

theNationalElectricalCode,ANSI/NFPA70-latesteditionand/orlocalcodes.

INCANADA:InstallationmustbeinaccordancewiththecurrentCAN/CGA-B149.1National

GasInstallationCodeorCAN/CGA-B149.2,PropaneInstallationCodeand/orlocalcodes.

ElectricalinstallationmustbeinaccordancewiththecurrentCSAC22.1CanadianElectrical

CodesPart1and/orlocalcodes.

INSTALLATIONINMANUFACTURED(MOBILE)HOME:Theinstallationmustconformwith

theManufacturedHomeConstructionandSafetyStandard,Title24CFR,Part3280[formerly

theFederalStandardforMobileHomeConstructionandSafety,Title24,HUD(Part280)]

or,whensuchstandardisnotapplicable,theStandardforManufacturedHomeInstallations,

ANSI/NCSBCSA225.1,orwithlocalcodeswhereapplicable.

INSTALLATIONINRECREATIONALPARKTRAILERS:Theinstallationmustconformwith

stateorothercodesor,intheabsenceofsuchcodes,withtheStandardforRecreational

ParkTrailers,ANSIA119.5.

Installation of any gas-red equipment should be made by a licensed plumber.A manual

shut-offvalvemustbeinstalledinanaccessiblelocationinthegaslineexternaltotheap-

plianceforthepurposeofturningonorshuttingoffgastotheappliance(InMassachusetts

suchshutoffdevicesshouldbeapprovedbytheBoardofStateExaminersofPlumbers&

GasFitters).

Ifanexternalelectricalsourceisutilized,theappliance,wheninstalled,mustbeelectrically

groundedinaccordancewithlocalcodesor,intheabsenceoflocalcodes,withthenational

ElectricalCode,ANSI/NFPA70.

WARNING !

To reduce the risk of tipping the appliance,

the appliance must be secured by properly

installed anti-tip device packed with the

appliance.

• ALL RANGES CAN TIP

• INJURY TO PERSONS COULD RESULT

• INSTALL ANTI-TIP DEVICE PACKED

WITH RANGE

• SEE INSTALLATION INSTRUCTIONS

– Do not store or use gasoline or other ammable vapors and

liquids in the vicinity of this or any other appliance.

– NEVER use this appliance as a space heater to heat or warm

the room. Doing so may result in carbon monoxide poiso-

ning and overheating of the appliance.

– WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• lmmediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• lf you cannot reach your gas supplier, call the re depart-

ment.

– Installation and service must be performed by a qualied

installer, service agency, or the gas supplier.

If the information in this manual is not followed exactly,

a re or explosion may result causing property damage,

personal injury, or death.

WARNING !

Thisapplianceisdesignedandmanufacturedsolelyforthecookingofdomestic(household)food

andinnotsuitableforanynonedomesticapplicationandthereforeshouldnotbeusedinacom-

mercialenvironmement.

Theappliancewarrantywillbevoidiftheapplianceisusedwithinanonedomesticenvironmement

i.e.asemicommercial,commercialorcommunalenvironment.

CONVERSIONLABEL

DATAPLATE

TheGovernorofCaliforniaisrequiredtopublishalistofsubstancesknowntothestateofCalifor-

niatocausecancerorreproductiveharmandrequiresbusinessestowarncustomersofpotential

exposurestosuchsubstances.

WARNING!: Gas appliances contain or produce substances which can cause death or serious

illnessandwhichareknowntotheStateofCaliforniatocausecancer,birthdefectsorotherrepro-

ductiveharm.Toreducetheriskfromsubstancesinfuelorfromfuelcombustion,makesurethis

applianceisinstalled,operated,andmaintainedaccordingtothemanufacturer’sinstructions.

The product data plate is

attachedinsidethebottom

pivotingpanel.

INSTALLATION INSTRUCTIONS

WARNING!

THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.

Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a quali-

ed installer, service agent, or the gas supplier.

Screwdriver 2 - Wrench

T-handle

wrench

Tape

measurePencil

Adjustable

pliers

Adjustable

wrench

Suitable protective

gloves

Drill

Hammer

TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)

IMPORTANT: The use of suitable protective clothing/gloves is

recommended when handling, installing of this appliance.

GENERAL INFORMATION

1. Installation must conform with local codes or,in the absen-

ceof local codes, with the National Fuel Gas Code,ANSI

Z223.1/NFPA54

-LatestEdition,CAN/CGA-B149.1orCAN/

CGA-B149.2.

2. Installationinmanufactured(mobile)home:installationmust

conform with the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280 [formerly the Fe-

deral Standard for Mobile Home Construction and Safety,

Title 24, HUD (Part 280)]or,whensuchstandardisnotappli-

cable,the StandardforManufactured Home Installations,

ANSI/NCSBCS A225.1,orwithlocalcodeswhereapplicable.

3. Installation in Recreational Park Trailers: installation must

conformwithstateorothercodesor,intheabsenceofsuch

codes, with the Standard for Recreational Park Trailers,

ANSI A119.5.

4. Toeliminateriskofburnsorrebyreachingoverheatedsur-

face units, cabinet storage located above the surface units

shouldbeavoided.

5. Aircurtainorotheroverheadrangehoods,whichoperateby

blowingadownwardairowontoarange,shallnotbeused

inconjunctionwithgasrangesotherthanwhenthehoodand

rangehavebeendesigned,testedandlistedbyanindepen-

denttestlaboratoryforuseincombination.

6. 

WARNING!!

 This appliance shall not be used for space heating. This

information is based on safety considerations.

7. AlIopeningsinthewallbehindtheapplianceandintheoor

undertheapplianceshallbesealed.

8. Keepapplianceareaclearandfreefromcombustiblemate-

rials,gasoline,andotherammablevapors.

9. Donotobstructtheowofcombustionandventilationair.

10. Disconnecttheelectricalsupplytotheappliancebeforeser-

vicing.

11. Whenremovingapplianceforcleaningand/orservice;

A. Shutoffgasatmainsupply.

B. DisconnectACpowersupply.

C. Disconnectgaslinetotheinletpipe.

D. Carefullyremovetherangebypullingoutward.

 CAUTION:Rangeisheavy;usecareinhandling.

12.

Electrical Requirement

Electrical installation should comply with national and local

codes.

13.

Air Supply and Ventilation

Theinstallermustreferstolocal/nationalcodes.

14.

Gas Manifold Pressure

Naturalgas-4.0”W.C.P.

LP/Propane-11.0”W.C.P.

15. Themisuseofovendoor(e.g.stepping,sitting,orleaningon

them)canresultinpotentialhazardsand/orinjuries.



WARNING!!

ELECTRICAL GROUNDING INSTRUCTIONS

The range must be electrically grounded in accordance with

local codes or, in the absence of local codes, with the Natio-

nal Electrical Code, ANSI/NFPA No. 70-latest edition, in Cana-

da Canadian Electrical Code.

Installation should be made by a Iicensed electrician.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PRO-

PERLY GROUNDED.

Ifanexternalelectricalsourceisutilized,theinstallationmustbe

electrically grounded in accordance with local codes or, in the

absenceof local codes,withthenationalElectrical Code,ANSI/

NFPA70.

REPLACEMENT PARTS

Onlyauthorizedreplacementpartsmaybeusedinperformingser-

viceontherange.Replacementpartsare availablefromfactory

authorizedpartsdistributors.Contactthenearestpartsdistributor

inyourarea.

16. Wheninstallingorremovingtherangeforservice,arollinglift

jackshouldbeused.Donotpushagainstanyoftheedgesof

therangeinanattempttoslideitintooroutoftheinstallation.

Pushingorpullingarange(ratherthanusingaliftjack)also

increases the possibility of bending the leg spindles or the

internalcouplingconnectors.

PROXIMITY TO SIDE CABINETS

1. Thisrangemaybeinstalleddirectlyadjacenttoexisting36”(914mm)

highbasecabinets.

 Rangedimensions:

• width:29”7/8(759mm)

• depth:24”13/64(614.9mm)

• height (without backguard): MIN 35” 21/32 (905.5 mm) - MAX 36”

11/32(923mm)

• backguard(height):3”(76mm)

 Gas line opening: Wall-37/64”(14.5mm)fromtherightsidetocentre

ofrange;from5”7/16(138mm)to6”1/8(155.5mm)[dependingonfeet

regulation]fromtheoor.

 Grounded outlet:shouldbelocated37/64”(14.5mm)fromtheleftside

tocentreofrange;from5”7/16(138mm)to6”1/8(155.5mm)[depen-

dingonfeetregulation]fromtheoor.

2. TherangeCANNOTbeinstalleddirectlyadjacenttosidewalls,tallcabi-

nets,tallappliances,orothersideverticalsurfacesabove36”(914mm)

high.

 Theremustbeaminimumof11”13/16(300mm)sideclearancefromthe

rangetosuchcombustiblesurfacesTOTHELEFTorTOTHERIGHT

abovethe36”(914mm)highcountertop.

 IMPORTANT: One side (left or right) above the 36” (914 mm) high

countertop must always be kept clear.

 Island installation: Theremustbeaminimumof12”(305mm)clearan-

cefrom therearofthe backguardtosuchcombustible surfaceonthe

backoftherangeabovethe36”(914mm)highcountertop.

3. Themaximumuppercabinetdepthrecommendedis13”(330mm).Wall

cabinetabovetherangemustbeaminimumof30”(762mm)abovethe

countertopforawidthofminimum30”(762mm):ithastobecentered

withtherange.Sidewallcabinetsabovetherangemustbeaminimum

of18”(457mm)abovethecountertop.

installation

Fig. 1.1

3”

(76mm)

MIN35”21/32(905.5mm)

MAX36”11/32(923mm)

24”13/64

(614.9mm)

29”7/8

(759mm)

ASSEMBLING THE BACKGUARD

It is mandatory to install the backguard.

Assemblethebackguardasshowningure1.3:

• Screwthe2screws“A”interposingthespacers.

• Screwthecentralscrew“B”.

Fig. 1.3

GAS AND ELECTRIC CONNECTION

Fig. 1.2

Dottedlineshowingtheposition

oftherangewheninstalled

Areafor

ELECTRICAL

connection

Areafor

GASconnection

Ref. inch mm

A 5”7/16-6”1/8(*) 138-155.5(*)

B 14”3/8 365

C 37/64” 14.5

(*):Dependingonfeetregulation

PROXIMITY TO SIDE CABINETS

STANDARD INSTALLATION

Fig. 1.4b

Fig. 1.4a

OVEN VENT

Ref. inch mm

A 0” 0

B 36” 914

C 11”13/16 300

D 30”minimum 762minimum

E 18”minimum 457minimum

F 13”maximum 330maximum

G 20”minimum 500minimum

OVEN VENT

PROXIMITY TO SIDE CABINETS

ISLAND INSTALLATION

Fig. 1.5b

Fig. 1.5a

OVEN VENT

Ref. inch mm

A 0” 0

B 36” 914

C 11”13/16 300

D 30”minimum 762minimum

E 18”minimum 457minimum

F 13”maximum 330maximum

G 20”minimum 500minimum

H 12”minimum 305minimum

OVEN VENT

LEVELLING THE RANGE

Therangeisequippedwith4LEVELLINGFEETandmaybelevelledbyscrewingor

unscrewingthefeet(gs.1.6-1.7).

Itisimportanttoobservethedirectionsofgures1.6,1.8a,1.8b.

Fig. 1.8bFig. 1.8a

Fig. 1.7

Fig. 1.6

Suppliedwiththerange

inaseparatekit

Suppliedwiththerange

inaseparatekit

0”

0mm

+5/16”

+8mm

+5/16”

+8mm

+11/16”

+17.5mm

Fig. 1.9

Dotted line showing the position

oftherangewheninstalled

ANTI-TIPSTABILITY

DEVICEFIXING

Anti-tipstability

device

Rearleft

feetofrange

3”15/64

(82mm)

YOU MUST USE STABILITY

ANTI TIP BRACKET TO

PREVENT UNIT FROM

TIPPING.

ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS

1. Theanti-tipbrackethastobeattachedasshownongurebelow(onlyrearleftside),

ithastobexedontheoorORontherearwallbyno.4(four)suitablescrews(not

supplied).Alternativelytheanti-tipbracketcanalsobexedontheoorANDonthe

rearwallbyno.8(eight)suitablescrews(notsupplied).

2. Afterxingtheanti-tipbracket,sliderangeintoplace.Besuretherearleftfootslides

undertheanti-tipbracketattached.

INSTALLING THE COOKTOP FRONT GUARD

Toincreasetheclearancebetweenthefrontedgeofthecooktopandtheburnersitispossibletoinstallthecooktopfrontguardsupplied

withtheappliance.

IMPORTANT: To install/remove the guard it is necessary to remove the cooktop.

Attempting to install/remove the guard without disassembling the cooktop will result in permanent damage to the appliance.

Installthefrontguardasshowningure1.10:

1. Removethebackguard.

2. Removethepansupports,theburnercapsandtheamespreaders.

3. Unscrewcooktopxingscrews(“A”ingurebelow).

4. Removethedualburnerinneramespreader(“B”ingurebelow).

5. Removethecooktop(keepattentionnottodamagethegasketsttedabovetheburnercups-belowthecooktop).

6. Installthefrontguard“C”byinsertingthewireterminalsintotheproperholesabovethecontrolpanel(“D”ingurebelow).

7. Reassemblethecooktopandtheothercomponents(stepsfrom5to1).

 Payspecialattentiontothegasketsttedabovetheburnercups

 (belowthecooktop);iftheyaredamagedtheyshallbereplaced.

Fig. 1.10

gas connection

2. Pressure Regulator:

a. Allheavyduty,commercialtypecookingequipmentmusthaveapressureregulator

ontheincomingservicelineforsafeandefcientoperation,sinceservicepressure

mayuctuatewithlocaldemand.

 Beforeinstallingtheregulatormountthe1/2”NPT(conical)maleconnectortothe

regulator(seepicture2.2).

 Gasketsuppliedhastobeplacedbetween1/2”NPT(conical)connector/extension

pipemalepipetting(seepicture2.3).

 Theregulatorsuppliedwiththisrangemustbeinstalledbeforeanygasconnections

aremade.

 Usesuppliedpressureregulatoronly.

Gas supply line

Shuto valve

“open” position

To range

Explosion Hazard

Use a new CSA or UL approved

gas supply line.

Install a shut-off valve.

Securely tighten all gas connec-

tions.

If connected to LP, have a quali-

fied person make sure gas pres-

sure does not exceed 14" water

column.

Examples of a qualified person

include licensed heating per-

sonnel, authorized gas compa-

ny personnel, and authorized

service personnel.

Failure to do so can result in

death, explosion, or fire.

Fig. 2.1

Allgasconnectionsmustbemadeaccordingtonationalandlocalcodes.Thisgassupply

(service)linemustbethesamesizeorgreaterthantheinletlineoftheappliance.Sea-

lantonallpipejointsmustberesistanttotheactionofLP/Propanegas.

TherangeisequippedfortheusewithNATURALgas.Itisdesign-certiedbyCSAInter-

nationalforNATURALandL.P.gaseswithappropriateconversion.

Themodel/serialratingplate,locatedinsidethebottompivotingpanel,hasinformation

onthetypeofgasthatcanbeused.Ifthisinformationdoesnotagreewiththetypeof

gasavailable,check with the local gas supplier. See pagefrom16 to 18 for L.P. gas

conversioninstructions.

1. Manual Shut-off Valve(g:2.1):

Amanualshut-offvalvemustbeinstalledinanaccessiblelocationinthegaslineexternal

totheapplianceforthepurposeofturningonorshuttingoffgastotheappliance(InMas-

sachusettssuchshutoffdevicesshouldbeapprovedbytheBoardofStateExaminersof

Plumbers&GasFitters).

Thisvalveshouldbelocatedinthesameroomastherangeandshouldbeinalocation

thatallowseaseofopeningandclosing(inapositionwhereitcanbereachedquicklyin

theeventofanemergency).

Donotblockaccesstotheshutoffvalve.Thevalveisforturningonorshuttingoffgas

totheappliance.

LOCK

Arrow

PRESSURE REGULATOR INSTALLATION

STEP 1

Mountthe1/2”NPT(conical)maleconnectortothepressureregulatorand

tightenbyusingawrench.

Donotovertightentheconnector.

Overtighteningmaycrackregulator.

STEP 2

Assemblethe1/2”NPTconnector+pressureregulatorgrouptotheextensionpipeinterposingthegasketsupplied.

Theregulatorcovermustbeorientedtowardthefrontsideoftherange.

IMPORTANT:usetwowrenchestotightentheconnection.

Fig. 2.3

Fig. 2.2

Regulatorcover

Gasket

Fig. 2.4

GAS CONNECTION SPEFICICATION

Range

manifold

Manifold male pipe tting

1/2”Gcylindrical

(ISO228-1)male

1/2”Gcylindrical

(ISO228-1)female

Gasket

Extension

pipe female

pipe tting

Torange

1/2”Gcylindrical

(ISO228-1)female

Extension

pipe

1/2”Gcylindrical

(ISO228-1)male

Extension

pipe male

pipe tting

Gasket

Connector

1/2”NPT(conical)

male

1/2”NPT

female

Pressure

regulator

1/2”NPT

female

Tomains

connection

Arrow

WARNING: check the right positioning of the gas

regulator.

The arrow on the back of the gas regulator must be

oriented toward the connector.

b. Anyconversionrequiredmustbeperformedbyyourdealeroraqualiedlicen-

sedtechnicianorgasservicecompany.Pleaseprovidetheservicepersonwith

thismanualbeforeworkisstartedontherange.(Gasconversionsarethere-

sponsibilityofthedealerorenduser.)

c. ThisrangecanbeusedwithNATURALorLP/PROPANEgas.Itisshippedfrom

thefactoryadjustedforusewithNATURALgas.

d. Manifold pressure should be checked with a manometer and by operating as

belowdetailed:

• Removetheinjectorfromtherearleft(orrearright)burnerandmountthe

proper test point adapter which is available from the After-Sales Service

(seesidegureandthe“OPERATIONSTOBEPERFORMEDWHENSUB-

STITUTINGTHEINJECTORS”chapter).

• Turntherearleft(orrearright)burnercontrolknobtothemaximumposi-

tion.

• Presstheknobandkeepingitpressedcheckthemanifoldpressurewitha

manometer;NATURALgasrequires4.0”W.C.P.andLP/PROPANErequires

11.0”W.C.P.

• Incominglinepressureupstreamfromtheregulatormustbe1”W.C.P.hi-

gherthanthemanifoldpressureinordertochecktheregulator.

• Theregulatorusedonthisrangecanwithstandamaximuminputpressure

of1/2PSI(14.0”W.C.P).Ifthelinepressureisinexcessofthatamount,a

stepdownregulatorwillberequired.

e. Theappliance,itsindividualshut-offvalve,andpressureregulatormustbedi-

sconnectedfromthegassupplypiping system during any pressure testing of

thatsystematpressuresinexcessof1/2PSI(3.5kPa).

f. Theappliancemustbeisolatedfromthegassupplypipingsystembyclosingits

individualmanual shut-offvalveduringany pressuretestingof thegassupply

pipingsystemattestpressureequaltoorlessthan1/2PSI(3.5kPa).

3. Flexible Connections:

Iflocalcodespermit,CSAorULdesign-certied,exiblemetalapplianceconnector

isrecommendedforconnectingthisrangetothegassupplyline.DoNotkinkorda-

magetheexibleconnectorwhenmovingtherange.Thepressureregulatorhas1/2”

NPTfemalepipethreads.Youwillneedtodeterminethettingsrequired,depending

onthesizeofyourgassupplyline,exiblemetalconnectorandshutoffvalve.

4. Rigid Pipe Connections:

Ifrigidpipeisusedasagassupplyline,acombinationofpipettingsmustbeusedto

obtainanin-lineconnectiontotherange.Allstrainsmustberemovedfromthesupply

andfuellinessorangewillbelevelandinline.

• Usejointcompoundsandgasketsthatareresistanttoactionofnaturalorpropa-

negasonallmalepipethreads.

• Donotovertightengasttingwhenattachingtopressureregulator.Overtighte-

ningmaycrackregulator.

5. Leak Testing:

IMPORTANT:Leaktestingoftheapplianceshallbeconductedasfollows:

• Afternalgasconnectionismade,turnonmanualgasvalveandtestallcon-

nectionsingassupply piping and appliance for gas leaks withasoapywater

solution.Duringthistestallappliancegasvalveshavetobeclosed.

• Inordertoavoidpropertydamageorseriouspersonalinjury,neveruseaIighted

match.Ifaleakispresent,tightenjointorunscrew,applymorejointcompound,

tightenagainandretestconnectionforleak.

Fig. 2.5

TESTPOINTADAPTER

The Test Point adapter is available from the

After-SalesService.

Pressure

regulator

NATURAL GAS

REGULATION

LP/PROPANE

REGULATION

REGULATOR COVER

CONVERSION TO LP/PROPANE GAS (OR CONVERSION BACK TO THE

ORIGINAL GAS - NATURAL GAS)

Everyrangeisprovidedwithasetofinjectorsforthevarioustypesofgas.

Selecttheinjectorstobereplacedaccordingtothe“INJECTORSTABLE”.

Thenozzlediameters,expressedinhundredthsofamillimetre,aremarkedonthebodyofeachinjector.

CAUTION: Save the orices removed from the appliance for future use.

SETTING THE PRESSURE REGULATOR

Thepressureregulatoris accessible by opening the pivotingpanel(g. 2.6); the pressure regulator is

positionedontherearrightsideoftherange(g.2.7).

To set the pressure regulator(g.2.7):

1. Unscrewtheregulatorcover.

2. Unscrewthe“A”component,reverseandscrewitaccordingtotheLP/PROPANE(orNATURALGAS)

regulation.

Fig. 2.6

Fig. 2.7

OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE

INJECTORS

• Removethepansupports,theburnercapsandtheamespreaders.

• Dualburneronly(g.2.9):Unscrewtheno.3xingscrews“A”andremovetheinner

crownamespreader“B”;thenunscrewtheno.2xingscrews“C”andremovethe

coverplate“D”.

• Usingawrenchsubstitutethenozzleinjectors“J

”,“J

”and“J

”(gs.2.8,2.9)with

thosemostsuitableforthekindofgasforwhichitistobeused.

• Dualburneronly(g.2.9):

Ret

thecoverplate“D”andscrewtheno.2xingscrews

“C”;thenrettheinnercrownamespreader“B”andscrewtheno.3xingscrews“A”

• Rettheamespreaders,theburnercapsandthepansupports.

The burner are conceived in such a way so as not to require the regulation of the

primary air.

SECOND ORIFICE

DEUXIEME ORIFICE

Fig. 2.9

Fig. 2.8

SEMI-RAPID BURNER

DUAL BURNER

INJECTORS TABLE

NOMINAL

POWER

REDUCED

POWER

LP/PROPANE

11”W.C.P.

NATURAL GAS

4”W.C.P.

BURNERS BTU/hr BTU/hr

Øinjector

[1/100mm]

Øinjector

[1/100mm]

Semirapid(SR) 8000 1500 85 139

Dual(D)

Innercrown 2100 1000

42(*)

115(**)

70(*)

200(**)

Inner&outercrown 17000 6500

(*) innercrown(“J

”ingure2.9)

(**) outercrown(“J

”ingure2.9)

Fig. 2.10

 Regulationscrew(Semirapidburner)

 Regulationscrew(Innercrownofdualburner)

 Regulationscrew(Outercrownofdualburner)

SETTING THE BURNER MINIMUM

Whenswitchingfromonetypeofgastoanother,theminimumowratemustalsobecor-

rect:theameshouldnotgooutevenwhenpassingsuddenlyfrommaximumtominimum

ame.

Toregulatetheame(g.2.10)followtheinstructionsbelow:

Semirapid burner

• Lighttheburner.

• Setthegasvalveto“

LO”position(minimumrate).

• Removetheknob.

• Withathinscrewdriver,turntheregulationscrew“R

”untiladjustmentiscorrect.

Inside crown of DUAL burner

• LighttheDUALburner.

• Setthegasvalveto“

”position(minimumrateofinnercrown).

• Removetheknob

• Withathinscrewdriver,turntheregulationscrew“R

”untiladjustmentiscorrect.

Outside crown of DUAL burner

• LighttheDUALburner.

• Setthegasvalveto“

”position(minimumrateofinnerandoutercrowns).

• Removetheknob.

• Withathinscrewdriver,turntheregulationscrew“R

”untiladjustmentiscorrect.

For LP/PROPANE gas, tighten the adjustment screws completely.

Afterregulationrepeattheoperationsindicatedinparagraph“2.PRESSUREREGULA-

TOR”atpage12and15.

Iftherangehasbeendisconnectedandthenconnectedagaintothegassupplylinerepe-

attheoperationsindicatedinparagraph“5.LEAKTESTING”atpage15.

IMPORTANT:

• AfterconversiontoLP/PROPANEgashasbeencarriedoutafxnearthedataplate

theconversionlabelsuppliedandalsoafxaconversionlabelatpage3ofthisin-

structionmanual.

• Afterconversionbacktotheoriginalgas(NATURALGAS)hasbeencarriedoutre-

move,nearthedataplateandatpage3ofthisinstructionmanual,theLP/PROPANE

conversionlabels.Savethelabelsremovedforfutureuse.

electrical connection

WARNING

TO AVOID ELECTRICAL SHOCK HA-

ZARD, BEFORE INSTALLING THE

APPLIANCE, SWITCH POWER OFF

AT THE SERVICE PANEL AND LOCK

THE PANEL TO PREVENT THE PO-

WER FROM BEING SWITCHED ON

ACCIDENTALLY.

ELECTRICAL REQUIREMENTS

• Thisappliancemustbeproperlyinstalledandgroundedbyaqualiedtechnicianin

accordancewiththeNationalElectricalCodeANSI/NFPANo.70(latestedition)and

localelectricalcoderequirements.

• Thisappliancemaybeconnectedbymeansofpermanent“HardWiring”or“Power

SupplyCordkit”.

• Powersupplycordisnotsupplied,butitisavailablethroughyourlocalelectricsup-

plyhouse.

• Useonly3-conductoror4-conductorCSA/ULlistedrangecordratedat30ampswith

250Vminimumandprovidedwithringterminals.Thesecordsshouldbeprovided

withstrainrelieforconduitconnector.

Warning: Framegroundedthroughneutrallead.Ifusedin,

– Newbranch-circuitinstallations(1996NEC),

– Mobilehomes,

– Recreationalvehicles,or

– Inanareawherelocalcodesprohibitgroundingthroughneutral,usea4con-

ductorcordorconduit.

• The range must be connected to the proper electrical voltage and frequency as

speciedontheratingplate.

• Therangecanbeconnecteddirectlytothefuseddisconnect(orcircuitbreakerbox)

throughexible,counduitwithcopperoraluminiumwiring(withgroundingwire).

 Allowtwotothreefeetofslackinthelinesothatitcanbemovedifservicingisever

necessary.

ELECTRICAL CONNECTION WITH POWER CORD

Usea3-wirepowersupplycordkitratedfor30amps-240-208/120voltswithclosedloop

terminalsandmarkedforusewithranges.

Wherelocalcodesdonotpermitgroundingthroughneutral,usea4-wirepowersupply

cord.

TheCSA/ULlistedcordmustbesecuredtotherangewithasuitablestrainreliefbra-

cket.

Theelectricalconnectionismadeattheterminalblock,whichislocatedbehindtheac-

cessdooronthebackoftherange.

ELECTRICAL CONNECTION WITH CONDUIT

Use1/2”(1.3cm)tradesizeCSA/ULlistedconduitwithaconduitclamp,16AWG/600

voltcopperconductorcolored redforline1andblackforline2and16AWG/600volt

copperconductor(or14AWG/600voltcopperconductorifgroundingthroughneutral)

coloredwhiteforneutralwithclosedloopterminalsmarkedforusewithranges.

Wherelocalcodesdonotpermitgroundingthroughneutral,useagreen14AWGcopper

conductorasdirectedinthe4-wireconnectordirections.

Theconduitmustbesecuredtotherangewiththestrainreliefbracket.

Theelectricalconnectionismadeattheterminalblock,whichislocatedbehindtheac-

cessdooronthebackoftherange.

3-Wire Power Cord Installation(SeeFigure3.2)

1. RemovetheTerminal Block Access Plateonthebackofthe

rangebyunscrewingthe4xingScrews(Figure3.1).

2. Check the correct positioning of thePower Cord Bracket as

pergure3.2.

3. AssemblethestrainreliefintheholeonPower Cord Bracket.

4. InsertthePower Cordthroughthestrainreliefandtighten.

5. Removethe3wireterminalnutsandwashersfromtheTermi-

nal Block.

6. PlugtheterminalholesofPower Cord.

 TheNeutral or Ground WireofthePower Cordmustbecon-

nectedtotheneutralterminallocatedinthecenterofTerminal

Block.

 The Power Wiresmustbeconnectedtotheoutsideterminals.

7. Plugwashersandtightennutssecurely.



DonotremoveGround strap.

8. ReassembletheTerminal Block Access Plateonthebackof

therangebyscrewingthe4xingScrews(Figure3.1).

4-Wire Power Cord Installation (SeeFigure3.3)

1. RemovetheTerminal Block Access Plateonthebackofthe

rangebyunscrewingthe4xingScrews(Figure3.1).

2. Check the correct positioning of thePower Cord Bracket as

pergure3.3.

3. AssemblethestrainreliefintheholeonPower Cord Bracket.

4. InsertthePower Cordthroughthestrainreliefandtighten.

5. Removethe3wireterminalnutsandwashersfromtheTermi-

nal Block.

6. RemovetheGround Strapfromtheframeofrangeandtermi-

nalbyremovingitsscrewandcuttingitasshowninFigure3.3.

7. PlugtheterminalholesofPower Cord.

 TheNeutral WireofthePower Cordmustbeconnectedtothe

neutral terminal located in the center of Terminal Block; the

Power Wiresmustbeconnectedtotheoutsideterminals;the

Ground Wiremustbeattachedtotheframeofrangebyusing

the(Ground)identied

Grounding Screw.

8. Plugwashersandtightennutssecurely.

9. ReassembletheTerminal Block Access Plateonthebackof

therangebyscrewingthe4xingScrews(Figure3.1).

Terminal Block

Ground strap

Neutral Wire

Power Wires

Power Cord

Bracket

A: D=1” 9/64 (29 mm)

B: D=7/8” (22.5 mm)

Terminal Block

Cut Ground Strap

Power Cord

Bracket

Neutral Wire

Power Wires

Grounding Wire

Grounding

Screw

A: D=1” 9/64 (29 mm)

B: D=7/8” (22.5 mm)

Power Cord

Terminal Block

Access Plate

Screws

Fig. 3.1

Fig. 3.2

Fig. 3.3

Page is loading ...

Verona VEFSGE 304 SC, VEFSGE 304 SC.. User manual

Related papers

Other documents