Verona VEFSGE 304 SC User manual

Brand: Verona

Model: VEFSGE 304 SC

Category: Cookers

Type: User manual

This manual is also suitable for

VEFSGE 304 SC..

Verona VEFSGE 304 SC.. is a gas/electric range for residential use only. It has a data plate attached inside the bottom pivoting panel. The range dimensions are: width 29” 7/8 (759 mm), depth 24” 13/64 (614.9 mm) and height (without backguard) MIN 35” 21/32 (905.5 mm) - MAX 36” 11/32 (923 mm). The backguard height is 3” (76 mm). It's equipped with a protective film on steel and aluminum parts that must be removed before installing and using the appliance. The range cannot be installed directly adjacent to sidewalls, tall cabinets, or other side vertical surfaces above 36” (914 mm) high.

GAS/ELECTRIC RANGE

for residential use only

THIS RANGE IS FOR RESIDENTIAL USE ONLY

FOR INSTALLER ONLY

Some models are supplied with a protective lm on steel and aluminium

parts. This lm must be removed before installing/using the appliance.

Models: VEFSGE 304 SC..

INSTALLATION INSTRUCTIONS

IMPORTANT - PLEASE READ AND FOLLOW

• Beforebeginning,pleasereadtheseinstructionscompletelyandcarefully.

• Donotremovepermanentlyafxedlabels,warnings,orplatesfromtheproduct.Thismay

voidthewarranty.

• Pleaseobservealllocalandnationalcodesandordinances.

• Pleaseensurethatthisproductisproperlygrounded.

• The installer should leave these instructions with the consumer who should retain

for local inspector’s use and for future reference.

Installationmustconformwithlocalcodesorintheabsenceofcodes,theNationalFuelGas

CodeANSIZ223.1/NFPA54-Iatestedition.Electricalinstallationmustbeinaccordancewith

theNationalElectricalCode,ANSI/NFPA70-latesteditionand/orlocalcodes.

INCANADA:InstallationmustbeinaccordancewiththecurrentCAN/CGA-B149.1National

GasInstallationCodeorCAN/CGA-B149.2,PropaneInstallationCodeand/orlocalcodes.

ElectricalinstallationmustbeinaccordancewiththecurrentCSAC22.1CanadianElectrical

CodesPart1and/orlocalcodes.

INSTALLATIONINMANUFACTURED(MOBILE)HOME:Theinstallationmustconformwith

theManufacturedHomeConstructionandSafetyStandard,Title24CFR,Part3280[formerly

theFederalStandardforMobileHomeConstructionandSafety,Title24,HUD(Part280)]

or,whensuchstandardisnotapplicable,theStandardforManufacturedHomeInstallations,

ANSI/NCSBCSA225.1,orwithlocalcodeswhereapplicable.

INSTALLATIONINRECREATIONALPARKTRAILERS:Theinstallationmustconformwith

stateorothercodesor,intheabsenceofsuchcodes,withtheStandardforRecreational

ParkTrailers,ANSIA119.5.

Installation of any gas-red equipment should be made by a licensed plumber.A manual

shut-offvalvemustbeinstalledinanaccessiblelocationinthegaslineexternaltotheap-

plianceforthepurposeofturningonorshuttingoffgastotheappliance(InMassachusetts

suchshutoffdevicesshouldbeapprovedbytheBoardofStateExaminersofPlumbers&

GasFitters).

Ifanexternalelectricalsourceisutilized,theappliance,wheninstalled,mustbeelectrically

groundedinaccordancewithlocalcodesor,intheabsenceoflocalcodes,withthenational

ElectricalCode,ANSI/NFPA70.

WARNING !

To reduce the risk of tipping the appliance,

the appliance must be secured by properly

installed anti-tip device packed with the

appliance.

• ALL RANGES CAN TIP

• INJURY TO PERSONS COULD RESULT

• INSTALL ANTI-TIP DEVICE PACKED

WITH RANGE

• SEE INSTALLATION INSTRUCTIONS

– Do not store or use gasoline or other ammable vapors and

liquids in the vicinity of this or any other appliance.

– NEVER use this appliance as a space heater to heat or warm

the room. Doing so may result in carbon monoxide poiso-

ning and overheating of the appliance.

– WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• lmmediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• lf you cannot reach your gas supplier, call the re depart-

ment.

– Installation and service must be performed by a qualied

installer, service agency, or the gas supplier.

If the information in this manual is not followed exactly,

a re or explosion may result causing property damage,

personal injury, or death.

WARNING !

Thisapplianceisdesignedandmanufacturedsolelyforthecookingofdomestic(household)food

andinnotsuitableforanynonedomesticapplicationandthereforeshouldnotbeusedinacom-

mercialenvironmement.

Theappliancewarrantywillbevoidiftheapplianceisusedwithinanonedomesticenvironmement

i.e.asemicommercial,commercialorcommunalenvironment.

CONVERSIONLABEL

DATAPLATE

TheGovernorofCaliforniaisrequiredtopublishalistofsubstancesknowntothestateofCalifor-

niatocausecancerorreproductiveharmandrequiresbusinessestowarncustomersofpotential

exposurestosuchsubstances.

WARNING!: Gas appliances contain or produce substances which can cause death or serious

illnessandwhichareknowntotheStateofCaliforniatocausecancer,birthdefectsorotherrepro-

ductiveharm.Toreducetheriskfromsubstancesinfuelorfromfuelcombustion,makesurethis

applianceisinstalled,operated,andmaintainedaccordingtothemanufacturer’sinstructions.

The product data plate is

attachedinsidethebottom

pivotingpanel.

INSTALLATION INSTRUCTIONS

WARNING!

THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.

Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a quali-

ed installer, service agent, or the gas supplier.

Screwdriver 2 - Wrench

T-handle

wrench

Tape

measurePencil

Adjustable

pliers

Adjustable

wrench

Suitable protective

gloves

Drill

Hammer

TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)

IMPORTANT: The use of suitable protective clothing/gloves is

recommended when handling, installing of this appliance.

GENERAL INFORMATION

1. Installation must conform with local codes or,in the absen-

ceof local codes, with the National Fuel Gas Code,ANSI

Z223.1/NFPA54

-LatestEdition,CAN/CGA-B149.1orCAN/

CGA-B149.2.

2. Installationinmanufactured(mobile)home:installationmust

conform with the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280 [formerly the Fe-

deral Standard for Mobile Home Construction and Safety,

Title 24, HUD (Part 280)]or,whensuchstandardisnotappli-

cable,the StandardforManufactured Home Installations,

ANSI/NCSBCS A225.1,orwithlocalcodeswhereapplicable.

3. Installation in Recreational Park Trailers: installation must

conformwithstateorothercodesor,intheabsenceofsuch

codes, with the Standard for Recreational Park Trailers,

ANSI A119.5.

4. Toeliminateriskofburnsorrebyreachingoverheatedsur-

face units, cabinet storage located above the surface units

shouldbeavoided.

5. Aircurtainorotheroverheadrangehoods,whichoperateby

blowingadownwardairowontoarange,shallnotbeused

inconjunctionwithgasrangesotherthanwhenthehoodand

rangehavebeendesigned,testedandlistedbyanindepen-

denttestlaboratoryforuseincombination.

6. 

WARNING!!

 This appliance shall not be used for space heating. This

information is based on safety considerations.

7. AlIopeningsinthewallbehindtheapplianceandintheoor

undertheapplianceshallbesealed.

8. Keepapplianceareaclearandfreefromcombustiblemate-

rials,gasoline,andotherammablevapors.

9. Donotobstructtheowofcombustionandventilationair.

10. Disconnecttheelectricalsupplytotheappliancebeforeser-

vicing.

11. Whenremovingapplianceforcleaningand/orservice;

A. Shutoffgasatmainsupply.

B. DisconnectACpowersupply.

C. Disconnectgaslinetotheinletpipe.

D. Carefullyremovetherangebypullingoutward.

 CAUTION:Rangeisheavy;usecareinhandling.

12.

Electrical Requirement

Electrical installation should comply with national and local

codes.

13.

Air Supply and Ventilation

Theinstallermustreferstolocal/nationalcodes.

14.

Gas Manifold Pressure

Naturalgas-4.0”W.C.P.

LP/Propane-11.0”W.C.P.

15. Themisuseofovendoor(e.g.stepping,sitting,orleaningon

them)canresultinpotentialhazardsand/orinjuries.



WARNING!!

ELECTRICAL GROUNDING INSTRUCTIONS

The range must be electrically grounded in accordance with

local codes or, in the absence of local codes, with the Natio-

nal Electrical Code, ANSI/NFPA No. 70-latest edition, in Cana-

da Canadian Electrical Code.

Installation should be made by a Iicensed electrician.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PRO-

PERLY GROUNDED.

Ifanexternalelectricalsourceisutilized,theinstallationmustbe

electrically grounded in accordance with local codes or, in the

absenceof local codes,withthenationalElectrical Code,ANSI/

NFPA70.

REPLACEMENT PARTS

Onlyauthorizedreplacementpartsmaybeusedinperformingser-

viceontherange.Replacementpartsare availablefromfactory

authorizedpartsdistributors.Contactthenearestpartsdistributor

inyourarea.

16. Wheninstallingorremovingtherangeforservice,arollinglift

jackshouldbeused.Donotpushagainstanyoftheedgesof

therangeinanattempttoslideitintooroutoftheinstallation.

Pushingorpullingarange(ratherthanusingaliftjack)also

increases the possibility of bending the leg spindles or the

internalcouplingconnectors.

PROXIMITY TO SIDE CABINETS

1. Thisrangemaybeinstalleddirectlyadjacenttoexisting36”(914mm)

highbasecabinets.

 Rangedimensions:

• width:29”7/8(759mm)

• depth:24”13/64(614.9mm)

• height (without backguard): MIN 35” 21/32 (905.5 mm) - MAX 36”

11/32(923mm)

• backguard(height):3”(76mm)

 Gas line opening: Wall-37/64”(14.5mm)fromtherightsidetocentre

ofrange;from5”7/16(138mm)to6”1/8(155.5mm)[dependingonfeet

regulation]fromtheoor.

 Grounded outlet:shouldbelocated37/64”(14.5mm)fromtheleftside

tocentreofrange;from5”7/16(138mm)to6”1/8(155.5mm)[depen-

dingonfeetregulation]fromtheoor.

2. TherangeCANNOTbeinstalleddirectlyadjacenttosidewalls,tallcabi-

nets,tallappliances,orothersideverticalsurfacesabove36”(914mm)

high.

 Theremustbeaminimumof11”13/16(300mm)sideclearancefromthe

rangetosuchcombustiblesurfacesTOTHELEFTorTOTHERIGHT

abovethe36”(914mm)highcountertop.

 IMPORTANT: One side (left or right) above the 36” (914 mm) high

countertop must always be kept clear.

 Island installation: Theremustbeaminimumof12”(305mm)clearan-

cefrom therearofthe backguardtosuchcombustible surfaceonthe

backoftherangeabovethe36”(914mm)highcountertop.

3. Themaximumuppercabinetdepthrecommendedis13”(330mm).Wall

cabinetabovetherangemustbeaminimumof30”(762mm)abovethe

countertopforawidthofminimum30”(762mm):ithastobecentered

withtherange.Sidewallcabinetsabovetherangemustbeaminimum

of18”(457mm)abovethecountertop.

installation

Fig. 1.1

3”

(76mm)

MIN35”21/32(905.5mm)

MAX36”11/32(923mm)

24”13/64

(614.9mm)

29”7/8

(759mm)

ASSEMBLING THE BACKGUARD

It is mandatory to install the backguard.

Assemblethebackguardasshowningure1.3:

• Screwthe2screws“A”interposingthespacers.

• Screwthecentralscrew“B”.

Fig. 1.3

GAS AND ELECTRIC CONNECTION

Fig. 1.2

Dottedlineshowingtheposition

oftherangewheninstalled

Areafor

ELECTRICAL

connection

Areafor

GASconnection

Ref. inch mm

A 5”7/16-6”1/8(*) 138-155.5(*)

B 14”3/8 365

C 37/64” 14.5

(*):Dependingonfeetregulation

PROXIMITY TO SIDE CABINETS

STANDARD INSTALLATION

Fig. 1.4b

Fig. 1.4a

OVEN VENT

Ref. inch mm

A 0” 0

B 36” 914

C 11”13/16 300

D 30”minimum 762minimum

E 18”minimum 457minimum

F 13”maximum 330maximum

G 20”minimum 500minimum

OVEN VENT

PROXIMITY TO SIDE CABINETS

ISLAND INSTALLATION

Fig. 1.5b

Fig. 1.5a

OVEN VENT

Ref. inch mm

A 0” 0

B 36” 914

C 11”13/16 300

D 30”minimum 762minimum

E 18”minimum 457minimum

F 13”maximum 330maximum

G 20”minimum 500minimum

H 12”minimum 305minimum

OVEN VENT

LEVELLING THE RANGE

Therangeisequippedwith4LEVELLINGFEETandmaybelevelledbyscrewingor

unscrewingthefeet(gs.1.6-1.7).

Itisimportanttoobservethedirectionsofgures1.6,1.8a,1.8b.

Fig. 1.8bFig. 1.8a

Fig. 1.7

Fig. 1.6

Suppliedwiththerange

inaseparatekit

Suppliedwiththerange

inaseparatekit

0”

0mm

+5/16”

+8mm

+5/16”

+8mm

+11/16”

+17.5mm

Fig. 1.9

Dotted line showing the position

oftherangewheninstalled

ANTI-TIPSTABILITY

DEVICEFIXING

Anti-tipstability

device

Rearleft

feetofrange

3”15/64

(82mm)

YOU MUST USE STABILITY

ANTI TIP BRACKET TO

PREVENT UNIT FROM

TIPPING.

ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS

1. Theanti-tipbrackethastobeattachedasshownongurebelow(onlyrearleftside),

ithastobexedontheoorORontherearwallbyno.4(four)suitablescrews(not

supplied).Alternativelytheanti-tipbracketcanalsobexedontheoorANDonthe

rearwallbyno.8(eight)suitablescrews(notsupplied).

2. Afterxingtheanti-tipbracket,sliderangeintoplace.Besuretherearleftfootslides

undertheanti-tipbracketattached.

INSTALLING THE COOKTOP FRONT GUARD

Toincreasetheclearancebetweenthefrontedgeofthecooktopandtheburnersitispossibletoinstallthecooktopfrontguardsupplied

withtheappliance.

IMPORTANT: To install/remove the guard it is necessary to remove the cooktop.

Attempting to install/remove the guard without disassembling the cooktop will result in permanent damage to the appliance.

Installthefrontguardasshowningure1.10:

1. Removethebackguard.

2. Removethepansupports,theburnercapsandtheamespreaders.

3. Unscrewcooktopxingscrews(“A”ingurebelow).

4. Removethedualburnerinneramespreader(“B”ingurebelow).

5. Removethecooktop(keepattentionnottodamagethegasketsttedabovetheburnercups-belowthecooktop).

6. Installthefrontguard“C”byinsertingthewireterminalsintotheproperholesabovethecontrolpanel(“D”ingurebelow).

7. Reassemblethecooktopandtheothercomponents(stepsfrom5to1).

 Payspecialattentiontothegasketsttedabovetheburnercups

 (belowthecooktop);iftheyaredamagedtheyshallbereplaced.

Fig. 1.10

gas connection

2. Pressure Regulator:

a. Allheavyduty,commercialtypecookingequipmentmusthaveapressureregulator

ontheincomingservicelineforsafeandefcientoperation,sinceservicepressure

mayuctuatewithlocaldemand.

 Beforeinstallingtheregulatormountthe1/2”NPT(conical)maleconnectortothe

regulator(seepicture2.2).

 Gasketsuppliedhastobeplacedbetween1/2”NPT(conical)connector/extension

pipemalepipetting(seepicture2.3).

 Theregulatorsuppliedwiththisrangemustbeinstalledbeforeanygasconnections

aremade.

 Usesuppliedpressureregulatoronly.

Gas supply line

Shuto valve

“open” position

To range

Explosion Hazard

Use a new CSA or UL approved

gas supply line.

Install a shut-off valve.

Securely tighten all gas connec-

tions.

If connected to LP, have a quali-

fied person make sure gas pres-

sure does not exceed 14" water

column.

Examples of a qualified person

include licensed heating per-

sonnel, authorized gas compa-

ny personnel, and authorized

service personnel.

Failure to do so can result in

death, explosion, or fire.

Fig. 2.1

Allgasconnectionsmustbemadeaccordingtonationalandlocalcodes.Thisgassupply

(service)linemustbethesamesizeorgreaterthantheinletlineoftheappliance.Sea-

lantonallpipejointsmustberesistanttotheactionofLP/Propanegas.

TherangeisequippedfortheusewithNATURALgas.Itisdesign-certiedbyCSAInter-

nationalforNATURALandL.P.gaseswithappropriateconversion.

Themodel/serialratingplate,locatedinsidethebottompivotingpanel,hasinformation

onthetypeofgasthatcanbeused.Ifthisinformationdoesnotagreewiththetypeof

gasavailable,check with the local gas supplier. See pagefrom16 to 18 for L.P. gas

conversioninstructions.

1. Manual Shut-off Valve(g:2.1):

Amanualshut-offvalvemustbeinstalledinanaccessiblelocationinthegaslineexternal

totheapplianceforthepurposeofturningonorshuttingoffgastotheappliance(InMas-

sachusettssuchshutoffdevicesshouldbeapprovedbytheBoardofStateExaminersof

Plumbers&GasFitters).

Thisvalveshouldbelocatedinthesameroomastherangeandshouldbeinalocation

thatallowseaseofopeningandclosing(inapositionwhereitcanbereachedquicklyin

theeventofanemergency).

Donotblockaccesstotheshutoffvalve.Thevalveisforturningonorshuttingoffgas

totheappliance.

LOCK

Arrow

PRESSURE REGULATOR INSTALLATION

STEP 1

Mountthe1/2”NPT(conical)maleconnectortothepressureregulatorand

tightenbyusingawrench.

Donotovertightentheconnector.

Overtighteningmaycrackregulator.

STEP 2

Assemblethe1/2”NPTconnector+pressureregulatorgrouptotheextensionpipeinterposingthegasketsupplied.

Theregulatorcovermustbeorientedtowardthefrontsideoftherange.

IMPORTANT:usetwowrenchestotightentheconnection.

Fig. 2.3

Fig. 2.2

Regulatorcover

Gasket

Fig. 2.4

GAS CONNECTION SPEFICICATION

Range

manifold

Manifold male pipe tting

1/2”Gcylindrical

(ISO228-1)male

1/2”Gcylindrical

(ISO228-1)female

Gasket

Extension

pipe female

pipe tting

Torange

1/2”Gcylindrical

(ISO228-1)female

Extension

pipe

1/2”Gcylindrical

(ISO228-1)male

Extension

pipe male

pipe tting

Gasket

Connector

1/2”NPT(conical)

male

1/2”NPT

female

Pressure

regulator

1/2”NPT

female

Tomains

connection

Arrow

WARNING: check the right positioning of the gas

regulator.

The arrow on the back of the gas regulator must be

oriented toward the connector.

b. Anyconversionrequiredmustbeperformedbyyourdealeroraqualiedlicen-

sedtechnicianorgasservicecompany.Pleaseprovidetheservicepersonwith

thismanualbeforeworkisstartedontherange.(Gasconversionsarethere-

sponsibilityofthedealerorenduser.)

c. ThisrangecanbeusedwithNATURALorLP/PROPANEgas.Itisshippedfrom

thefactoryadjustedforusewithNATURALgas.

d. Manifold pressure should be checked with a manometer and by operating as

belowdetailed:

• Removetheinjectorfromtherearleft(orrearright)burnerandmountthe

proper test point adapter which is available from the After-Sales Service

(seesidegureandthe“OPERATIONSTOBEPERFORMEDWHENSUB-

STITUTINGTHEINJECTORS”chapter).

• Turntherearleft(orrearright)burnercontrolknobtothemaximumposi-

tion.

• Presstheknobandkeepingitpressedcheckthemanifoldpressurewitha

manometer;NATURALgasrequires4.0”W.C.P.andLP/PROPANErequires

11.0”W.C.P.

• Incominglinepressureupstreamfromtheregulatormustbe1”W.C.P.hi-

gherthanthemanifoldpressureinordertochecktheregulator.

• Theregulatorusedonthisrangecanwithstandamaximuminputpressure

of1/2PSI(14.0”W.C.P).Ifthelinepressureisinexcessofthatamount,a

stepdownregulatorwillberequired.

e. Theappliance,itsindividualshut-offvalve,andpressureregulatormustbedi-

sconnectedfromthegassupplypiping system during any pressure testing of

thatsystematpressuresinexcessof1/2PSI(3.5kPa).

f. Theappliancemustbeisolatedfromthegassupplypipingsystembyclosingits

individualmanual shut-offvalveduringany pressuretestingof thegassupply

pipingsystemattestpressureequaltoorlessthan1/2PSI(3.5kPa).

3. Flexible Connections:

Iflocalcodespermit,CSAorULdesign-certied,exiblemetalapplianceconnector

isrecommendedforconnectingthisrangetothegassupplyline.DoNotkinkorda-

magetheexibleconnectorwhenmovingtherange.Thepressureregulatorhas1/2”

NPTfemalepipethreads.Youwillneedtodeterminethettingsrequired,depending

onthesizeofyourgassupplyline,exiblemetalconnectorandshutoffvalve.

4. Rigid Pipe Connections:

Ifrigidpipeisusedasagassupplyline,acombinationofpipettingsmustbeusedto

obtainanin-lineconnectiontotherange.Allstrainsmustberemovedfromthesupply

andfuellinessorangewillbelevelandinline.

• Usejointcompoundsandgasketsthatareresistanttoactionofnaturalorpropa-

negasonallmalepipethreads.

• Donotovertightengasttingwhenattachingtopressureregulator.Overtighte-

ningmaycrackregulator.

5. Leak Testing:

IMPORTANT:Leaktestingoftheapplianceshallbeconductedasfollows:

• Afternalgasconnectionismade,turnonmanualgasvalveandtestallcon-

nectionsingassupply piping and appliance for gas leaks withasoapywater

solution.Duringthistestallappliancegasvalveshavetobeclosed.

• Inordertoavoidpropertydamageorseriouspersonalinjury,neveruseaIighted

match.Ifaleakispresent,tightenjointorunscrew,applymorejointcompound,

tightenagainandretestconnectionforleak.

Fig. 2.5

TESTPOINTADAPTER

The Test Point adapter is available from the

After-SalesService.

Pressure

regulator

NATURAL GAS

REGULATION

LP/PROPANE

REGULATION

REGULATOR COVER

CONVERSION TO LP/PROPANE GAS (OR CONVERSION BACK TO THE

ORIGINAL GAS - NATURAL GAS)

Everyrangeisprovidedwithasetofinjectorsforthevarioustypesofgas.

Selecttheinjectorstobereplacedaccordingtothe“INJECTORSTABLE”.

Thenozzlediameters,expressedinhundredthsofamillimetre,aremarkedonthebodyofeachinjector.

CAUTION: Save the orices removed from the appliance for future use.

SETTING THE PRESSURE REGULATOR

Thepressureregulatoris accessible by opening the pivotingpanel(g. 2.6); the pressure regulator is

positionedontherearrightsideoftherange(g.2.7).

To set the pressure regulator(g.2.7):

1. Unscrewtheregulatorcover.

2. Unscrewthe“A”component,reverseandscrewitaccordingtotheLP/PROPANE(orNATURALGAS)

regulation.

Fig. 2.6

Fig. 2.7

OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE

INJECTORS

• Removethepansupports,theburnercapsandtheamespreaders.

• Dualburneronly(g.2.9):Unscrewtheno.3xingscrews“A”andremovetheinner

crownamespreader“B”;thenunscrewtheno.2xingscrews“C”andremovethe

coverplate“D”.

• Usingawrenchsubstitutethenozzleinjectors“J

”,“J

”and“J

”(gs.2.8,2.9)with

thosemostsuitableforthekindofgasforwhichitistobeused.

• Dualburneronly(g.2.9):

Ret

thecoverplate“D”andscrewtheno.2xingscrews

“C”;thenrettheinnercrownamespreader“B”andscrewtheno.3xingscrews“A”

• Rettheamespreaders,theburnercapsandthepansupports.

The burner are conceived in such a way so as not to require the regulation of the

primary air.

SECOND ORIFICE

DEUXIEME ORIFICE

Fig. 2.9

Fig. 2.8

SEMI-RAPID BURNER

DUAL BURNER

INJECTORS TABLE

NOMINAL

POWER

REDUCED

POWER

LP/PROPANE

11”W.C.P.

NATURAL GAS

4”W.C.P.

BURNERS BTU/hr BTU/hr

Øinjector

[1/100mm]

Øinjector

[1/100mm]

Semirapid(SR) 8000 1500 85 139

Dual(D)

Innercrown 2100 1000

42(*)

115(**)

70(*)

200(**)

Inner&outercrown 17000 6500

(*) innercrown(“J

”ingure2.9)

(**) outercrown(“J

”ingure2.9)

Fig. 2.10

 Regulationscrew(Semirapidburner)

 Regulationscrew(Innercrownofdualburner)

 Regulationscrew(Outercrownofdualburner)

SETTING THE BURNER MINIMUM

Whenswitchingfromonetypeofgastoanother,theminimumowratemustalsobecor-

rect:theameshouldnotgooutevenwhenpassingsuddenlyfrommaximumtominimum

ame.

Toregulatetheame(g.2.10)followtheinstructionsbelow:

Semirapid burner

• Lighttheburner.

• Setthegasvalveto“

LO”position(minimumrate).

• Removetheknob.

• Withathinscrewdriver,turntheregulationscrew“R

”untiladjustmentiscorrect.

Inside crown of DUAL burner

• LighttheDUALburner.

• Setthegasvalveto“

”position(minimumrateofinnercrown).

• Removetheknob

• Withathinscrewdriver,turntheregulationscrew“R

”untiladjustmentiscorrect.

Outside crown of DUAL burner

• LighttheDUALburner.

• Setthegasvalveto“

”position(minimumrateofinnerandoutercrowns).

• Removetheknob.

• Withathinscrewdriver,turntheregulationscrew“R

”untiladjustmentiscorrect.

For LP/PROPANE gas, tighten the adjustment screws completely.

Afterregulationrepeattheoperationsindicatedinparagraph“2.PRESSUREREGULA-

TOR”atpage12and15.

Iftherangehasbeendisconnectedandthenconnectedagaintothegassupplylinerepe-

attheoperationsindicatedinparagraph“5.LEAKTESTING”atpage15.

IMPORTANT:

• AfterconversiontoLP/PROPANEgashasbeencarriedoutafxnearthedataplate

theconversionlabelsuppliedandalsoafxaconversionlabelatpage3ofthisin-

structionmanual.

• Afterconversionbacktotheoriginalgas(NATURALGAS)hasbeencarriedoutre-

move,nearthedataplateandatpage3ofthisinstructionmanual,theLP/PROPANE

conversionlabels.Savethelabelsremovedforfutureuse.

electrical connection

WARNING

TO AVOID ELECTRICAL SHOCK HA-

ZARD, BEFORE INSTALLING THE

APPLIANCE, SWITCH POWER OFF

AT THE SERVICE PANEL AND LOCK

THE PANEL TO PREVENT THE PO-

WER FROM BEING SWITCHED ON

ACCIDENTALLY.

ELECTRICAL REQUIREMENTS

• Thisappliancemustbeproperlyinstalledandgroundedbyaqualiedtechnicianin

accordancewiththeNationalElectricalCodeANSI/NFPANo.70(latestedition)and

localelectricalcoderequirements.

• Thisappliancemaybeconnectedbymeansofpermanent“HardWiring”or“Power

SupplyCordkit”.

• Powersupplycordisnotsupplied,butitisavailablethroughyourlocalelectricsup-

plyhouse.

• Useonly3-conductoror4-conductorCSA/ULlistedrangecordratedat30ampswith

250Vminimumandprovidedwithringterminals.Thesecordsshouldbeprovided

withstrainrelieforconduitconnector.

Warning: Framegroundedthroughneutrallead.Ifusedin,

– Newbranch-circuitinstallations(1996NEC),

– Mobilehomes,

– Recreationalvehicles,or

– Inanareawherelocalcodesprohibitgroundingthroughneutral,usea4con-

ductorcordorconduit.

• The range must be connected to the proper electrical voltage and frequency as

speciedontheratingplate.

• Therangecanbeconnecteddirectlytothefuseddisconnect(orcircuitbreakerbox)

throughexible,counduitwithcopperoraluminiumwiring(withgroundingwire).

 Allowtwotothreefeetofslackinthelinesothatitcanbemovedifservicingisever

necessary.

ELECTRICAL CONNECTION WITH POWER CORD

Usea3-wirepowersupplycordkitratedfor30amps-240-208/120voltswithclosedloop

terminalsandmarkedforusewithranges.

Wherelocalcodesdonotpermitgroundingthroughneutral,usea4-wirepowersupply

cord.

TheCSA/ULlistedcordmustbesecuredtotherangewithasuitablestrainreliefbra-

cket.

Theelectricalconnectionismadeattheterminalblock,whichislocatedbehindtheac-

cessdooronthebackoftherange.

ELECTRICAL CONNECTION WITH CONDUIT

Use1/2”(1.3cm)tradesizeCSA/ULlistedconduitwithaconduitclamp,16AWG/600

voltcopperconductorcolored redforline1andblackforline2and16AWG/600volt

copperconductor(or14AWG/600voltcopperconductorifgroundingthroughneutral)

coloredwhiteforneutralwithclosedloopterminalsmarkedforusewithranges.

Wherelocalcodesdonotpermitgroundingthroughneutral,useagreen14AWGcopper

conductorasdirectedinthe4-wireconnectordirections.

Theconduitmustbesecuredtotherangewiththestrainreliefbracket.

Theelectricalconnectionismadeattheterminalblock,whichislocatedbehindtheac-

cessdooronthebackoftherange.

3-Wire Power Cord Installation(SeeFigure3.2)

1. RemovetheTerminal Block Access Plateonthebackofthe

rangebyunscrewingthe4xingScrews(Figure3.1).

2. Check the correct positioning of thePower Cord Bracket as

pergure3.2.

3. AssemblethestrainreliefintheholeonPower Cord Bracket.

4. InsertthePower Cordthroughthestrainreliefandtighten.

5. Removethe3wireterminalnutsandwashersfromtheTermi-

nal Block.

6. PlugtheterminalholesofPower Cord.

 TheNeutral or Ground WireofthePower Cordmustbecon-

nectedtotheneutralterminallocatedinthecenterofTerminal

Block.

 The Power Wiresmustbeconnectedtotheoutsideterminals.

7. Plugwashersandtightennutssecurely.



DonotremoveGround strap.

8. ReassembletheTerminal Block Access Plateonthebackof

therangebyscrewingthe4xingScrews(Figure3.1).

4-Wire Power Cord Installation (SeeFigure3.3)

1. RemovetheTerminal Block Access Plateonthebackofthe

rangebyunscrewingthe4xingScrews(Figure3.1).

2. Check the correct positioning of thePower Cord Bracket as

pergure3.3.

3. AssemblethestrainreliefintheholeonPower Cord Bracket.

4. InsertthePower Cordthroughthestrainreliefandtighten.

5. Removethe3wireterminalnutsandwashersfromtheTermi-

nal Block.

6. RemovetheGround Strapfromtheframeofrangeandtermi-

nalbyremovingitsscrewandcuttingitasshowninFigure3.3.

7. PlugtheterminalholesofPower Cord.

 TheNeutral WireofthePower Cordmustbeconnectedtothe

neutral terminal located in the center of Terminal Block; the

Power Wiresmustbeconnectedtotheoutsideterminals;the

Ground Wiremustbeattachedtotheframeofrangebyusing

the(Ground)identied

Grounding Screw.

8. Plugwashersandtightennutssecurely.

9. ReassembletheTerminal Block Access Plateonthebackof

therangebyscrewingthe4xingScrews(Figure3.1).

Terminal Block

Ground strap

Neutral Wire

Power Wires

Power Cord

Bracket

A: D=1” 9/64 (29 mm)

B: D=7/8” (22.5 mm)

Terminal Block

Cut Ground Strap

Power Cord

Bracket

Neutral Wire

Power Wires

Grounding Wire

Grounding

Screw

A: D=1” 9/64 (29 mm)

B: D=7/8” (22.5 mm)

Power Cord

Terminal Block

Access Plate

Screws

Fig. 3.1

Fig. 3.2

Fig. 3.3

Page is loading ...

Verona VEFSGE 304 SC User manual

Brand: Verona

Model: VEFSGE 304 SC

Category: Cookers

Type: User manual

This manual is also suitable for

VEFSGE 304 SC..

Download PDF

report

Verona VEFSGE 304 SC User manual

This manual is also suitable for

Verona VEFSGE 304 SC User manual

Related papers

Other documents