TEAC MCDV66BT User manual

MCDV66BT

DVD Micro System

WARRANTY PROCEDURE

v1.5.2: DEC 2011

Please read the owner’s manual carefully and ensure that you have followed the correct installation and operating

procedures.

1. Please read this warranty card.

2. Keep your purchase receipt to enable you to proceed quickly in the event of a Warranty Service.

3. If you require Warranty Service, please contact the TEAC Customer Support Hotline at 1300 553 315 for

assistance. Please ensure that you have the model number, serial number and purchase receipt ready when

yo

u call.

Please complete the section below and keep this information for your own records.

Owner’s Name

Owner’s Address

Postcode

Model Name/No. Serial No.

Dealer’s Name

Dealer’s Address

Postcode

Authorised Service Centres in Major Australian Cities

NSW

151 Arthur Street

Homebush West, NSW 2140

Queensland

Unit 1, 320 Curtin Ave West

Eagle Farm, QLD 4009

W

estern Australia

Unit 2, 50 Pilbara Street

Welshpool, WA 6106

S

outh Australia

11 McInnes Street

Ridleyton, SA 5008

Victoria

282 Normanby Road

South Melbourne, VIC 3205

Thank you for selecting a TEAC product

.

If you should require assistance with your product regarding its setup

or operation, or if any difficulties arise, please call us directly for advice

between Monday to Friday at 8.30AM – 6PM AEST at the

TEAC Customer Support Hotline

1300 553 315

teacservicesupport@awa.com.au

www.teac.com.au

WARRANTY INFORMATION

v1.5.2: DEC 2011

Our goods come w ith guarantees that cannot be excluded under t he Australian Consumer Law. You are

e

ntitled to a replacement or refund for a major failur e and for compensation for any other reasonably

f

oreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail

t

o be of acceptable quality and the failure does not amount to a major failure.

Warranty Terms & Conditions

1. TEAC warrants that this product is free from defects in material and workmanship under normal domestic use with

reasonable care and skill. Maintenance and cleaning (i.e. laser head) is not covered by this warranty. The TEAC

warranty only applies to TEAC products purchased, used and serviced in Australia.

2. The benefits to the consumer given by this Warranty are in addition to other rights and remedies of the consumer

un

der a law in relation to goods or services to which the warranty relates, being the Australian Consumer Law.

3. Refund or replacement via your retailer is available for a period of 14 days after purchase for goods that have been

inspected and determined to have a major failure. Refund and exchange is not applicable for change of mind.

4. Subject to the terms herein, this warranty effectively covers the equipment as specified

in the Warranty Periods

Table below from the date of purchase.

T

EAC PRODUCT

W

ARRANTY PERIOD

LED/LCD TV 32” (80 cm) and above 1 Year (In-Home Service/ Pick up Available)*

All other TEAC products 1 Year (Carry-in Service)

5.

This service will only be provided as part of this warranty if all the following conditions are met;

In Home Service/Pick up* Service

a) The product is indicated in the Warranty Period Table.

b) The product is within the warranty period.

c) The product is located within the normal service area of the local TEAC Authorised Service Centre.

If TEAC determines that the product is not repairable on site, TEAC can complete the repair by taking the product to

a TEAC Authorised Service Centre.

Where In-Home service/Pick up* is not available, the purchaser is required to send the product to the nearest TEAC

Aut

horised Service Centre for repair. In this event, proof of purchase is required to support a warranty claim. After

the repair, the product will be available for collection by or return to the purchaser at a fee upon request. TEAC in-

home service can be made available at a fee upon request.

Carry-in Service

6. A 12-month replacement warranty is applicable to all Accessories such as Remote, Power Adaptors and Cables.

7. TEAC will ensure to the best of its abilities that all required parts are made available for any required service/repair.

8. TEAC Australia Pty Ltd and its Authorised Service Centres will use their best endeavours to complete product

repairs within a reasonable period based on available resources and workload during the time when service is

re

quested and performed.

9. Refurbished parts may be used to repair the product. In the case of a replacement, the product may be replaced,

with a refurbished unit of the same type or, if one is unavailable, a similar refurbished model with equal or better

features & specifications.

10. Please be advised that if the product presented for repair is capable of retaining user-generated data, the data may

be lost dur

ing servicing. Customers are strongly encouraged to back up all important information/data before

sending the product in for service/repair.

11. Service will be provided only during normal business hours and under safety conditions and circumstances. TEAC

and its authorised service agents can refuse any repair if safety, in relation to OH&S, becomes a concern to its staff

or authorised service agents’ personnel.

12.

The warranty is void and warranty claims may be refused, subject to the Australian Consumer Law, if:

a) The product was not transported, installed, operated or maintained according to manufacturer instruction, or

b) The product was abused, damaged, tampered, altered or repaired by any unauthorised persons, or

c) Product failure is due to accidents during use, installation or transit, power surges, use of defective or

incompatible external devices, exposure to abnormal conditions such as excessive temperatures or humidity, or

en

try of liquids, objects or creatures into the product.

13. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection with the

sale of any equipment other than as stated in this warranty and outlined above.

14. TEAC reserves the right to inspect and verify whether the product is exhibiting a major failure as claimed by

cu

stomers/retailers.

15. LCD dead pixel policy, please contact TEAC Customer Support Hotline on 1300 553 315 for assistance.

3

9

10

11

9

10

11

5

6

7

8

Panel Overview

Initial Set Up

Connecting Video

Connecting Audio and FM

Ramote Control Overview

Before Use

Safety Precautions

Safety Instructions and Maintenance

Before Use

Power source: Only use this

unit with the electrical current

indicated on the label.

Keep the unit and the power

plug away from water and

moisture.

Avoid rain, direct sunlight and

excessive heat.

Never open the cover if you

are not authorised service

personnel. Avoid dropping

small metal objects into the

unit enclosure.

Protect the power cable from

heavy weights and do not step

on it. Do not pull or bend

excessively.

If the unit is not used for a long

time, unplug the unit from the

wall power outlet.

S

Before Use

User Manual

FM Antenna

Remote Control

2x AAA Batteries

AV Cable

OPEN/CLOSE

PLAY/PAUSE

VOLUME

VFD DISPLAY

DVD DOOR

H

USB PORT

ON/STANDBY

EADPHONE JACK

SOURCE

Accessory List

Panel Overview

CUSTOMER SUPPORT HOTLINE:

[email protected]

www.teac.com.au

1300553315

Contact Card

5

CAUTION: Always disconnect units from power when making or changing any cable

connections to avoid risk of electric shock.

Unit Connection

1. Connect the SPEAKERS OUT R+ channel of the DVD player to the jack of the R+ jack on

the right speaker, and the R- channel to the R- jack on the right speaker.

2. In the same way, connect the L+ and L- channels to the L+ and L- jacks on the left speaker.

Remote Control Battery Installation

1. Open the battery compartment on the back of the remote control.

2. Insert 2x AAA batteries by matching the +/- polarities marked in the compartment.

3. Close the battery compartment.

Note: To avoid leaking or cracking cells, install the batteries correctly according to polarity.

Use the correct type of batteries. Batteries that look similar may differ in voltage.

Always replace both batteries at the same time. Do not expose batteries to heat or flame.

Remote Control Operating Range

The remote control can be used up to approximately 5 meters straight ahead of the unit. It

can also be operated at a horizontal angle up to 30

o

from the remote control sensor.

If the remote control doesn’t operate properly:

- Check the polarity of the installed batteries (+/-)

- Check if the batteries are drained

- Check if the remote control sensor is blocked by obstacles.

- Check if there is any flourescent lighting, sunlight or other interferences nearby.

Initial Set Up

1. For a basic connection, connect the provided AV cables according to in the figure below. Set

the TV to AV input mode.

2. For a more vivid picture, use AV wires to connect the YPbPr jacks according to in the

figure below.

CAUTION: Ensure that all units are turned off and disconnected from the AC power outlet before

making or changing cable connections.

1. When watching discs in different video formats, adjust video format settings so that the formats

match. (NTSC/PAL/AUTO)

2. If there are multiple connections between the DVD player and the TV, we recommend that one

of them is selected and the rest are unplugged so that image and sound quality is not affected.

3. Do not switch the power on and off quickly in succession, please allow an interval of 3 seconds

before switching the power on/off again.

Option

6

Connecting Video

CAUTION: Ensure that all units are turned off and disconnected from the AC power outlet before

making or changing cable connections.

Connecting Audio and FM

8

Battery Installation

1. Open the battery compartment by taking out the battery cover.

2. Insert 2 AAA batteries, making sure to match +/- polarities correctly.

3. Close the battery compartment securely.

Note: Remove battery if the remote control is not used for a long time.

Do not mix old and new batteries.

MCDV66BT

MUTE

POWER

NUMBER

PROG

STOP

SOURCE

MENU

SETUP

DVD/USB

SEARCH

S

UBTITLE

ANGLE

COPY

ZOOM

N/P

V-MODE

OPEN/CLOSE

PREV/CH-

NEXT/CH+

REV/FF-

FWD/FF+

GOTO

VOLUME

SOUND

PLAY/PAUSE

ENTER

PBC

TITLE

DIRECTION

REPEAT

LANGUAGE

A-B

SLOW

RETURN

LOUDNESS

OSD

LOUDNESS

MEMORY

Remote Control Overview

9

To play a disc, select DVD Mode with the

SOURCE button. If you are using video

output to a TV, turn on the TV and switch

it to the correct input mode according to

the connection type being used.

a logo

(|<<)

(>>|)

(

)

FF+

(

)

FF-

exit the screen saver.

. If the screen saver turns on

Basic DVD Playback

10

if available on the DVD.

GOTO

title selection menu.The unit

beginning of the disc

digits or arrow navigation buttons

GOTO

Advanced DVD Playback

(OSD)

11

SOURCE

Press this button repeatedly for different

zoom options: 2x, 3x, 4x, 1/2x, 1/3, 1/4x,

1x. When zoomed in, use the arrow buttons

to move the viewing frame.

Press this button in DVD Mode to switch to

USB/CARD playback. A compatible USB

flash drive or SD/MMC/MS card containing

compatible media files must be connected

to use this feature.

NOTE: Press the SOURCE button to enter

DVD Mode.

Press this button for sound balance

adjustment. Press it repeatedly to cycle

through the following: TREBLE, BASS,

VOLUME. Use the volume +/- buttons to

increase/decrease the settings.

playback speed

Press this button to cycle through the

following input sources: DVD/AV/FM.

Note: The programmed list is not saved

in memory when the disc is ejected or the

unit is powered off

DVD/USB

Advanced DVD Playback

SOUND

00 1/172

00 :01

03 :11

12 8k b p s

001

002

003

004

12

After an audio disc is loaded,

to select a desired

(|<</ >>|)

Music File

When a music data disc is loaded,

to select a desired folder

folder.

file list

to select a desired file

After a Kodak Picture CD is loaded

.

to select a desired

display the current

picture file formats

After a JPEG CD is loaded

.

Music/Picture CD Playback

Gen er al

Audio

Tv D i splay

General setup Page

Angle Mark

On

Os d L an g

ENG

Cap t i o n

Of f

Sc r een S av er

On

Last Mem ory

On

Set T v D i s play M ode

Do lby

Vi d eo

Pr ef er en c e

●●

PS

Wide

●

Gen er al

Audio

Gen er al set u p Page

Cl osed C ap l i on

Do lby

Vi d eo

Pr ef er en c e

●●

Of f

Gen er al

Audio

Do lby

Vi d eo

Pr ef er en c e

Off

Os d L an g

Cap t i o n

Tv D i splay

Gen er al set u p Page

●●

PS

Angle Mark

On

ENG

Of f

Sc r een S av er

On

Set A n g l e Mar k

Gen er al

Audio

Tv D i splay

Gen er al set u p Page

Angle Mark

On

Os d L an g

ENG

Cap t i o n

Of f

Sc r een S av

e

r

On

Set O s d L an g u ag e

Do lby

Vi d eo

Pr ef er en c e

●●

PS

En glish

Fr en c h

Ger m an

Sp an i s h

On

No rmal /Ps

No rmal /L b

13

HDCD

1X

Las t Mem ory

On

DCHD

1X

a

L st Memory

On

HDCD

1X

MP3 Lyric mode

On

MP3 Lyric mode

On

Cap t i o n

Of f

Sc r een S av er

On

Las t Mem ory

On

DCHD

1X

MP3 Lyric mode

On

MP3 Lyric mode

On

Menu Setup

Gen er al

Audio

Gen er al s elu p Pag e

Sc reen S av er

Do lby

Vi d eo

Pref eren ce

●●

On

Of f

Vi d eo

Preference

Sp dif Set u p

Gen er al

Audio

Audio Setup Page

Go To Sp eak er Set u p P ag e

Do lby

●

●●

Video

Preference

Spdi f Off

General

Audio

DIGITA L AUDIO SETUP PAGE

Sp dif Output

Set u p S p dif

Dolby

Spdi f/Raw

Spdi f/Pc m

Tv D i splay

Angle Mark

On

Os d L an g

ENG

Cap t i o n

Of f

Sc r een S av er

On

Las t Memory

Last Mem o r y

On

PS

14

When the power is cut off suddenly, the

player can remember where it stopped.

After the player is turned on again, it can

continue to play from the previous point.

F.Last Memory

Last Mem ory

On

HDCD

1X

E.HDCD

High definition compatible digital cd.

2X

Gen er al

Audio

Gen er al s elu p Pag e

Do lby

Vi d eo

Pref eren ce

●●

Tv D i splay

Angle Mark

On

Os d L an g

ENG

Cap t i o n

Of f

Sc r een S av er

On

PS

Last Mem ory

On

HDCD

1X

HDCD

1X

Of f

MP3 Lyric mode On

puteS ekoara K

k 84 tuO mcpL

Menu Setup

Page is loading ...

TEAC MCDV66BT User manual

TEAC MCDV66BT User manual

Related papers

Other documents