Danfoss AMV 335, AMV 435 Operating instructions

Type
Operating instructions
2
1a
1b
B
100% / FULL!
A
100% / FULL!
Installation Guide AMV 335, AMV 435
DEN-SMT/SI VI.LE.I3.3B District Energy
33
- for 24V
- for 230V
7.5 sec/mm (FAST) 15 sec/mm (SLOW)
S [mm] T [sec] S [mm] T [sec]
10 75 10 150
15 112.5 15 225
20 150 20 300
green (red if used with AB-QM)
red (green if used with AB-QM)
green (red if used with AB-QM)
red (green if used with AB-QM)
-A
Installation Guide AMV 335, AMV 435
District Energy VI.LE.I3.3B DEN-SMT/SI
4
~ 60°
+
DEN-SMT/SI VI.LE.I3.3B District Energy
100% / FULL!
Installation Guide AMV 335, AMV 435
DEN-SMT/SI VI.LE.I3.3B District Energy
55
District Energy VI.LE.I3.3B DEN-SMT/SI
Installation Guide AMV 335, AMV 435
District Energy VI.LE.I3.3B DEN-SMT/SI
Sikkerhedsnoter
Disse instruktioner skal læses omhyggeligt
forud for montering og indkøring samt
respekteres for at undgå skader på
personer og udstyr.
Nødvendigt monterings-, opstarts- og
vedligeholdelsesarbejde må kun udføres
af faglært og autoriseret personale.
Forud for monterings- og
vedligeholdelsesarbejde på regulatoren
skal systemet være:
- trykløst
- nedkølet
- tømt
- rengjort.
Systemproducentens eller -operatørens
instruktioner skal overholdes.
Safety Note
To avoid injury and damage to persons
and devices, it is absolutely necessary
these instructions are carefully read
and observed prior to assembly and
commissioning.
Necessary assembly, start-up, and
maintenance work must be performed
only by qualied, trained and authorised
personnel.
Prior to assembly and maintenance work
on the controller, the system must be:
- depressurised
- cooled down
- emptied
- cleaned
Please comply with the instructions of the
system manufacturer or system operator.
Do not remove the cover before the
power supply is fully switched o.
Disposal instruction
This product should be
dismantled and its
components sorted, if
possible, in various groups
before recycling or disposal.
Always follow the local disposal
regulations.
Mounting
Installation and wiring
Do not touch anything on the PCB!
Switch o the power line before wiring
the actuator! Lethal voltage!
Wire the actuator according to the wiring
diagram.
DIP switch setting
- 24 V version
SW 1: Not used
SW 2: FAST/SLOW - Speed selector
SW 3: Not used
SW 4: Not used
- 230 V version
SW 1: FAST/SLOW - Speed selector
SW 2: Not used
Manual operation
LED function indiction
Dismounting
Dækslet må ikke ernes, før
strømforsyningen
er ernet fra
stikkontakten.
Bortskaelse
Før genbrug eller
bortskaelse skal dette
produkt skilles ad, og
enkeltdelene skal sorteres i
forskellige
materialegrupper.
Der henvises til de lokale bestemmelser
for bortskaelse.
Montering
Installation og ledningsføring
Rør ikke ved noget som helst på
printkortet!
Sluk for strømmen inden elektrisk
tilslutning
af motoren! Livsfarlig
spænding!
Tilslut motoren iht. ledningsdiagrammet.
* hurtig (fast)
** langsom (slow)
Manuel overstyring
Funktionslysdiode
* grøn (green)
** rød (red)
Afmontering
FAST SLOW
FAST SLOW
DANSK
ENGLISH
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Danfoss AMV 335, AMV 435 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI