Lucent Technologies CellPipe IAD 8T Hardware Installation Manual

Brand: Lucent Technologies

Model: CellPipe IAD 8T

Category: Serial switch boxes

Type: Hardware Installation Manual

This manual is also suitable for

CellPipe IAD 4A

CellPipe™ IAD 4A and

CellPipe

™ IAD 8T

Hardware Installation Guide

Part Number: 7820-0791-001

For software version 2.0

January 2001

Lucent Technologies

This material is protected by the copyright laws of the United States and other countries. It may not be reproduced, distributed, or

altered in any fashion by any entity (either internal or external to Lucent Technologies), except in accordance with applicable

agreements, contracts, or licensing, without the express written consent of Lucent Technologies. For permission to reproduce or

distribute, please email your request to [email protected].

Notice

Every effort was made to ensure that the information in this document was complete and accurate at the time of printing, but infor-

mation is subject to change.

Safety, Compliance, and Warranty Information

Before handling any Lucent Access Networks hardware product, read the Edge Access Safety and Compliance Guide included in

your product package. See that guide also to determine how products comply with the electromagnetic interference (EMI) and

network compatibility requirements of your country. See the warranty card included in your product package for the limited

warranty that Lucent Technologies provides for its products.

Security Statement

In rare instances, unauthorized individuals make connections to the telecommunications network through the use of access

features.

Copyrights for Third-Party Software Included in Lucent Access Networks Software Products

Permission to use, copy, modify, distribute, and sell this software and its documentation for any purpose is hereby granted without

fee, provided that the above copyright notice appear in all copies and that both that copyright notice and this permission notice

appear in supporting documentation. Neither Hewlett-Packard nor Silicon Graphics makes any representations about the suit-

ability of this software for any purpose. It is provided “as is” without express or implied warranty.

reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the

following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions, and

the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and

the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials

mentioning features or use of this software must display the following acknowledgement: This product includes software devel-

oped by the University of California, Berkeley, and its contributors. 4. Neither the name of the University nor the names of its

contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBU-

TORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

Feedback

Lucent Technologies appreciates your comments, either positive or negative, about this manual. Please send them to

[email protected].

Trademarks

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide iii

Trademarks

4ESS, 5ESS, A Network of Expertise, AnyMedia, APX 8000, AqueView, AUDIX,

B-STDX 8000, B-STDX 9000, ...Beyond Compare, CaseView, Cajun, CajunDocs,

CAJUNVIEW, Callmaster, CallVisor, CBX 500, CellPipe, ChoiceNet, ClearReach,

ComOS, cvMAX, DACScan, Dacsmate, Datakit, DEFINITY, Definity One,

DSLMAX, DSLTerminator, DSLPipe, DSLTNT, Elemedia, Elemedia Enhanced,

EMMI, End to End Solutions, EPAC, eSight, ESS, EVEREST,

Gigabit-scaled campus networking, Globalview, GRF, GX 250, GX 550,

HyperPATH, Inferno, InfernoSpaces, Intragy, IntragyAccess, IntragyCentral, Intuity,

IP Navigator, IPWorX, LineReach, LinkReach, MAX, MAXENT, MAX TNT,

Multiband, Multiband PLUS, Multiband RPM, MultiDSL, MultiVoice, MultiVPN,

Navis, NavisAccess, NavisConnect, NavisCore, NavisRadius, NavisXtend, NetCare,

NetLight, NetPartner, OneVision, Open Systems Innovations, OpenTrunk, P550,

PacketStar, PathStar, Pinnacle, Pipeline, PMVision, PortMaster, SecureConnect,

Selectools, Series56, SmoothConnect, Stinger, SYSTIMAX, True Access, WaveLAN,

WaveMANAGER, WaveMODEM, WebXtend, and

Where Network Solutions Never End are trademarks of Lucent Technologies Inc.

Advantage Pak, Advantage Services, AnyMedia, ...Beyond Compare,

End to End Solutions, Inter.NetWorking, MAXENT, and

NetWork Knowledge Solutions are service marks of Lucent Technologies Inc. Other

trademarks, service marks, and trade names mentioned in this publication belong to

their respective owners.

Ordering Information

You can order the most up-to-date product information and computer-based training

online at http://www.lucent.com/ins/bookstore.

Customer Service

To obtain product and service information, software upgrades, and technical

assistance, visit the eSight™ Service Center at http://www.esight.com. The

center is open 24 hours a day, seven days a week.

Customer Service

iv CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

Finding information and software

The eSight Service Center at http://www.esight.com provides technical

information, product information, and descriptions of available services. Log in and

select a service. The eSight Service Center also provides software upgrades, release

notes, and addenda. Or you can visit the FTP site at ftp://ftp.ascend.com for

this information.

Obtaining technical assistance

The eSight™ Service Center at http://www.esight.com provides access to

technical support. You can obtain technical assistance through email or the Internet,

or by telephone.

If you need to contact Lucent Technologies for assistance, make sure that you have

the following information available:

• Active contract number, product name, model, and serial number

• Software version

• Software and hardware options

• If supplied by your carrier, service profile identifiers (SPIDs) associated with

your line

• Your local telephone company’s switch type and operating mode, such as AT&T

5ESS Custom or Northern Telecom National ISDN-1

• Whether you are routing or bridging with your Lucent product

• Type of computer you are using

• Description of the problem

Obtaining assistance through email or the Internet

If your services agreement allows, you can communicate directly with a technical

engineer through Email Technical Support or eSight Live chat. Select one of these

sites when you log in to http://www.esight.com.

Calling the technical assistance center (TAC)

If you cannot find an answer through the tools and information on eSight or if you

have a very urgent need, contact TAC. Access the eSight Service Center at

Important safety instructions

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide v

http://www.esight.com and click Contact Us below the Lucent

Technologies logo for a list of telephone numbers inside and outside the United

States.

You can alternatively call (800) 272-3634 for a menu of Lucent services, or call

(510) 769-6001 for an operator. If you do not have an active services agreement or

contract, you will be charged for time and materials.

Important safety instructions

1 Read and follow all warning notices and instructions marked on the product or

included in the manual.

2 There are no operator serviceable parts within the unit. Refer all servicing to

trained service personnel.

3 Product installation should be performed by trained service personnel only.

4 Install only in restricted-access areas in accordance with UL1950, C22.2 No. 950,

and IEC60950

5 The maximum recommended operating ambient is 122° F (50° C). Allow

sufficient air circulation or space between units when installed in a closed or

multiple-rack assembly.

6 Slots and openings in the cabinet are provided for ventilation. To ensure reliable

operation of the product and to protect it from overheating, these slots and

openings must not be blocked or covered. Installation without sufficient airflow

can be unsafe.

7 Equipment mounted in a rack should be distributed to prevent a possible

hazardous condition due to uneven loading. The rack should safely support the

combined weight of all equipment. This product weighs 8 lbs.

8 The power source has to be adequately rated to assure safe operation of the

equipment. The building installation and/or power source must provide overload

protection.

9 Protective earth (PE) connection is essential to ensure safe operation before

connecting to the power supply and telecommunication network. Do not defeat

the purpose of the grounding-type plug by modifying the plug or using an

adapter. Use an outlet tester or a voltmeter to check the ac receptacle for the

presence of earth ground. If the receptacle is not properly grounded, the

Important safety instructions

vi CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

installation must not proceed until a qualified electrician has corrected the

problem.

If the power supply is fed from a power source with no protective-earthing path

(such as in certain Nordic countries), connect an earth-grounded copper wire to

the dedicated wiring terminal marked with (PE symbol) on the chassis. The

minimum size of the wire for a Pipeline unit with rated input current not

exceeding 6A is AWG 18 and cross-sectional area 0.75 mm

Models with ac power inputs are intended for use with a single-phase three-wire

power cord (which includes earthing conductor).

For models with dc power inputs, the protective earth connection must be

established by using the dedicated earthing terminal marked with the PE symbol

or, if provided, the earthing pin of the input terminal block.

10 Models with dc power inputs must be connected to a -48V dc supply source that

is electrically isolated from the ac source in accordance with UL1950, C22.2 No.

950, and IEC60950.

11 For products installed in Nordic countries (except Central Office equipment), a

type B plug or permanent connection must be used for connections to the main

power supply.

12 Before installing wires to the dc power terminal block, verify that these wires are

not connected to any power source. Installing live wires (that is, wires connected

to a power source) is hazardous.

13 Do not allow anything to rest on the power cord, and do not locate the product

where people will walk on the power cord.

14 Do not attempt to service this product yourself. Opening or removing covers can

expose you to dangerous high voltage points or other risks. Refer all servicing to

qualified service personnel.

15 General purpose cables are provided with this product. Special cables, which

might be required by the regulatory inspection authority for the installation site,

are the responsibility of the customer.

16 When installed in the final configuration, the product must comply with the

applicable safety standards and regulatory requirements of the country in which

it is installed. If necessary, consult with the appropriate regulatory agencies and

inspection authorities to ensure compliance.

17 A rare phenomenon can create a voltage potential between the earth grounds of

two or more buildings. If products installed in separate buildings are

interconnected, the voltage potential might cause a hazardous condition. Consult

Important safety instructions

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide vii

a qualified electrical consultant to determine whether or not this phenomenon

exists.

In addition, if the equipment is to be used with telecommunications circuits, take the

following precautions:

• Never install telephone wiring during a lightning storm.

• Never install telephone jacks in wet locations unless the jack is specifically

designed for wet locations.

• Never touch uninsulated telephone wires or terminals unless the telephone line

has been disconnected at the network interface.

• Use caution when installing or modifying telephone lines.

• Avoid using equipment connected to telephone lines (other than a cordless

telephone) during an electrical storm. There is a remote risk of electric shock

from lightning.

• Do not use a telephone or other equipment connected to telephone lines to report

a gas leak in the vicinity of the leak.

Warning: To reduce the risk of fire, communication cable conductors must be

26 AWG (0.13 mm

) or larger.

Avertissement: Afin de réduire les risques d'incendie, les fils conducteurs du

câble de communication doivent être d'un calibre minimum de 26 AWG

(American Wire Gauge), c'est-à-dire d'un minimum de 0,13 mm².

Warnung: Um Feuer-Risiko zu reduzieren, müsssen die Querschnitte der

Kommunikationskabel-Leiter 0,13 mm² oder größer sein.

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide ix

Contents

Trademarks .............................................................................................................. iii

Ordering Information ............................................................................................... iii

Customer Service ..................................................................................................... iii

Important safety instructions ..................................................................................... v

Introduction ............................................................................. 1

New CellPipe products .............................................................................................. 1

Lucent TURN-UP ...................................................................................................... 2

Serial connection ....................................................................................................... 2

Configuring your communications software ............................................................. 2

Preparing to upgrade .................................................................................................. 3

Locating the software binary file(s) ......................................................................... 3

Power supply ............................................................................................................. 4

CellPipe IAD 4A ....................................................................... 5

Connecting a CellPipe IAD 4A unit .......................................................................... 5

Checking the activity of CellPipe IAD 4A status lights ............................................ 6

Configuring a CellPipe IAD 4A unit ......................................................................... 8

CellPipe IAD 8T ....................................................................... 9

Connecting a CellPipe IAD 8T unit .......................................................................... 9

Checking the activity of CellPipe IAD 8T status lights .......................................... 10

Configuring a CellPipe IAD 8T unit ....................................................................... 12

Connector Pinouts ................................................................ 15

TERMINAL pinouts ................................................................................................ 15

Contents

x CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

10/100 LAN connector pinouts ............................................................................... 15

T1 Connector pinouts .............................................................................................. 16

ADSL connector pinouts ......................................................................................... 16

FCC Regulations .................................................................. 17

FCC Part 15 Notice .................................................................................................. 17

IC CS-03 Notice ...................................................................................................... 18

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide 1

Introduction

New CellPipe products

The CellPipe IAD 4A and CellPipe IAD 8T are now part of the CellPipe™ product

line that run the IAD (Integrated Access Device) v. 2.0 software. These are integrated

access devices supporting both voice and data communications.

This Hardware Installation Guide provides information for connecting these new

units to your computer. For additional information, refer to the CellPipe™ IAD User’s

Guide.

New CellPipe products. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Lucent TURN-UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Serial connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Configuring your communications software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Preparing to upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Locating the software binary file(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction

Lucent TURN-UP

2 CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

Lucent TURN-UP

The CellPipe IAD 4A and CellPipe IAD 8T units support the Lucent TURN-UP

automated provisioning system. TURN-Up is enabled when a user powers up his unit,

which is then automatically configured via the configuration server located at his

Internet Service Provider (ISP). TURN-UP eliminates the need for user configuration

of units and provides centralized management of configuration information.

Caution: If you attempt to manually configure the unit, a Delete Management Port

message will appear. If you select this option, the Lucent TURN-UP feature will be

disabled to enable you to reconfigure the unit.

Serial connection

You need to establish a serial connection to upgrade software and manually configure

the CellPipe units. Connect a serial cable (a serial communication cable designed for

connecting an external device) from your computer to the CellPipe unit. The cable

must be a high-speed cable that supports the hardware handshaking technique used by

almost all recently manufactured modems. The cable must have the appropriate

connector for connection to a serial communication port on your computer and a

DB-9 connector for connection to the TERMINAL port on the CellPipe unit.

Configuring your communications software

Use a communications program (such as HyperTerm, PROCOMM PLUS, Zterm, or

any other program that supports VT100 terminal emulation) to open a session directly

with the port to which the IAD unit is connected.

Configure your communications software with the following settings. If you are not

already familiar with the settings listed, see the documentation that accompanies your

communications software. If you are using the software for the first time, going

through an online or printed tutorial is a good way to get started.

• Direct connection—Indicate that a serial cable connects the IAD directly to the

computer.

Introduction

Preparing to upgrade

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide 3

• Serial port—Specify which of the computer’s serial ports the software uses. If the

only serial port available is currently used by an internal modem, you may need

to use your computer’s setup software to specify an external connector for the

port that will be used in place of the internal modem. In some cases, you also

may need to remove the modem. See the manual for the modem and your

computer’s user manual for details.

• Terminal type—Specify VT100.

• Duplex—Most communications software support full-duplex transmission by

default. If given a choice, set Full duplex.

• Bits per second—Specify 9600.

• Data bits—Specify 8.

• Parity—Specify None.

• Stop bits—Specify 1.

• Flow control—Disable software flow control (XON/XOFF) and, if possible,

hardware flow control (RTS/CTS).

When you establish the connection, the command-line interface appears.

Preparing to upgrade

Set up a TFTP server on the network that is accessible by your CellPipe unit prior to

upgrading the software. Also, configure an IP address on the 10BaseT port of the

CellPipe unit and test the connection to the TFTP server by pinging the server.

Locating the software binary file(s)

Caution: Do not upgrade to an earlier software version. Uploading older software

causes the unit to loose configuration, and you will have to return it for replacement.

You can locate the software binary file (or collection of software binary files) for the

IAD CellPipes at

ftp://ftp.ascend.com/pub/Software-Releases/CellPipe.

Introduction

Power supply

4 CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

The software loads for each CellPipe unit are different. Make certain that you

download the correct file. If you use the wrong file to upgrade, your unit will stop

functioning and you will have to restore your configuration from a backup.

Extract and save the appropriate file to the TFTP boot directory from which you will

upgrade your unit.

Power supply

All CellPipe units are shipped with a power supply. However, European users need to

purchase an additional wall outlet cable due to the regional variations in wall outlets.

Please check with your Sales Representative for the power supply and cables required

for your environment. Refer to the illustrations below.

Domestic power supply European power supply

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide 5

CellPipe IAD 4A

The CellPipe IAD 4A supports four POTS (plain old telephone service) lines over

ATM (Asynchronous Transfer Mode), PPP (Point-to-Point Protocol) over ATM,

Frame Relay or HDLC (High-Level Data Link Control) over an ADSL (asymmetrical

digital subscriber line) WAN interface. This unit supports asymmetrical transmission

and receive downstream rates of 64 Kbps to 8.1 Mbps and upstream rates of 64 Kbps

to 800 Kbps.

Connecting a CellPipe IAD 4A unit

The CellPipe IAD box you receive contains the following items:

1 CellPipe IAD unit

2 10BaseT Ethernet crossover cable (yellow)

3 ADSL WAN cable with RJ-11 modular plug connectors (blue)

4 Power supply

5 CellPipe™ IAD User’s Guide

6 Hardware Installation Guide

Connecting a CellPipe IAD 4A unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Checking the activity of CellPipe IAD 4A status lights. . . . . . . . . . . . . . . . . . . . . . 6

Configuring a CellPipe IAD 4A unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CellPipe IAD 4A

Checking the activity of CellPipe IAD 4A status lights

6 CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

7 Warranty card

To connect to the CellPipe IAD 4A unit, proceed as follows:

1 Connect one end of the yellow Ethernet cable to the port labeled LAN on your

unit and the other end to the Ethernet adapter on your computer.

Note: To connect the CellPipe unit to an Ethernet hub, use a straight-through

Ethernet cable (not supplied).

2 Connect one end of the blue WAN cable to the port labeled WAN and plug the

other end into the wall jack.

3 Connect up to four telephone lines to the four POTS ports.

4 Connect the power cable to your unit.

5 Plug the other end of the power cable into a wall outlet.

Note: The unit has no power switch and connecting the power cable turns on the

CellPipe IAD unit.

Checking the activity of CellPipe IAD 4A status

lights

Observe the activity pattern of the lights on the front of the CellPipe IAD 4A unit to

verify that the unit is connected properly.

CellPipe IAD 4A

Checking the activity of CellPipe IAD 4A status lights

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide 7

When all the cables are connected, verify that the following status light behavior

takes place:

• The pwr light is on initially and remains on. If not on, make sure the power

supply is properly connected.

• The act light blinks during any LAN traffic. Otherwise, it remains off.

• The lnk light is on if an Ethernet connection is established. If not on, check to

make sure your Ethernet cable is properly connected.

• The wan light blinks until a DSL connection is established, and then it remains

on.

• The con light is on only during the CellPipe IAD unit self-test and blinks when a

voice port is offhook.

CellPipe IAD 4A

Configuring a CellPipe IAD 4A unit

8 CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

Configuring a CellPipe IAD 4A unit

Caution: If you attempt to manually configure the unit, a Delete Management Port

message appears. The unit disables Lucent TURN-UP to enable you to manually

configure the unit.

The Main menu items for the CellPipe IAD 4A unit are similar to those of other IAD

CellPipe units. Refer to the CellPipe™ IAD User’s Guide for a discussion of the Main

menu items. The menu exception for the CellPipe IAD 4A can be found in its

Configure WAN menu.

To configure the WAN interface on the CellPipe IAD 4A unit, proceed as follows:

1 Select Configure WAN from the Main Menu.

2 Select Configure Physical Interface under the WAN Configuration

menu.

3 Set the ADSL Standard. See Table 1.

Table 1. ADSL ATU-R configuration menu

Menu option Description

Set ADSL Standard Current ADSL Standard: T1.413

Choose an ADSL Standard:

1. T1.413

2. G.Lite

3. G.DMT

4. Alcatel 1.4

5. Multi-Mode

6. ADI

7. Alcatel

CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide 9

CellPipe IAD 8T

The CellPipe IAD 8T supports eight POTS lines over ATM, PPP over ATM, Frame

Relay or HDLC (High-Level Data Link Control) over a T1 WAN interface. This

voice-over-T1 solution supports symmetrical transmission and receive rates of 1.544

Mbps.

Connecting a CellPipe IAD 8T unit

The CellPipe IAD box you receive contains the following items:

1 CellPipe IAD unit

2 10BaseT Ethernet crossover cable (yellow)

3 T1 WAN cable (blue)

4 Power supply

5 CellPipe™ IAD User’s Guide

6 Hardware Installation Guide

Connecting a CellPipe IAD 8T unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Checking the activity of CellPipe IAD 8T status lights. . . . . . . . . . . . . . . . . . . . . 10

Configuring a CellPipe IAD 8T unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CellPipe IAD 8T

Checking the activity of CellPipe IAD 8T status lights

10 CellPipe IAD 4A and CellPipe IAD 8T Hardware Installation Guide

7 Warranty card

To connect to the CellPipe IAD 8T unit, proceed as follows:

1 Connect one end of the yellow Ethernet cable to the port labeled LAN on your

unit and the other end to the Ethernet adapter on your computer.

Note: To connect the CellPipe unit to an Ethernet hub, use a straight-through

Ethernet cable (not supplied).

2 Connect one end of the blue WAN cable to the port labeled WAN and plug the

other end into the wall jack.

3 Connect up to eight telephone lines to the eight POTS ports.

4 Connect the power cable to your unit.

5 Plug the other end of the power cable into a wall outlet.

Note: The unit has no power switch and connecting the power cable turns on the

CellPipe IAD unit.

Checking the activity of CellPipe IAD 8T status

lights

Observe the activity pattern of the lights on the front of the CellPipe IAD 8T unit to

verify that the unit is connected properly.

Page is loading ...

Lucent Technologies CellPipe IAD 8T Hardware Installation Manual

Brand: Lucent Technologies

Model: CellPipe IAD 8T

Category: Serial switch boxes

Type: Hardware Installation Manual

This manual is also suitable for

CellPipe IAD 4A

Download PDF

report

Lucent Technologies CellPipe IAD 8T Hardware Installation Manual

This manual is also suitable for

Lucent Technologies CellPipe IAD 8T Hardware Installation Manual

Related papers

Other documents