Gigaset DX800A all in one User guide

Brand: Gigaset

Model: DX800A all in one

Category: Mobile phones

Type: User guide

This manual is also suitable for

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 /

Congratulations

By purchasing a Gigaset, you have chosen a brand that is fully committed

to sustainability. This product’s packaging is eco-friendly!

To learn more, visit www.gigaset.com.

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 /

Gigaset DX800A all in one, DX600A ISDN and DL500A – your perfect companion

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / introduction.fm / 24.03.11

Version 4, 16.09.2005

Gigaset DX800A all in one, DX600A ISDN and DL500A –

your perfect companion

... impressive inside and out. Go crazy for the vibrant 3.5" TFT display, first-class sound quality

and elegant exterior. Your Gigaset can do a lot more than just make calls:

Bluetooth, Ethernet, DECT and (device-specific) FAX port

Connect your Gigaset to the Internet and your PC via Ethernet. Use public and private direc-

tories on the Internet (

¢ page 39). Update the directory on your Gigaset, the address book

on your Bluetooth mobile phone and your directory on the PC simultaneously.

Directory with vCards – calendar and appointments

Save phone numbers and other data to the local directory (¢ page 38). Enter appointments

and anniversaries in the calendar and set reminders.

Use your Gigaset as a PABX

Using the Bluetooth interface, you can register up to five GSM mobile phones. You can con-

nect one of the mobile phones with the base and make calls using this GSM connection –

Link2mobile.

Go online with your Gigaset

Use your phone's Info Centre and have information specifically provided for the phone from

the Internet shown on the display.

Do not disturb

Switch off the display backlight at night (¢page 48), use time control for calls (¢ page 49)

or reject unknown calls (

¢ page 49).

Other practical information

Transfer the directory from an existing Gigaset handset (¢ page 38), use the programmable

function keys (

¢ page 47) for speed dial and quick access to important functions, use the

convenient headset to make calls, read your e-mail messages (without a PC) on your phone.

It's easy to configure your Gigaset DX800A all in one/DX600A ISDN thanks to

the wizards

These determine the MSNs for your ISDN connection and general VoIP provider data (pro-

vider-specific) and assist you with registering handsets and assigning send and receive con-

nections to the base, handsets, fax machine and integrated answering machine (

¢ page 16).

Environment

Gigaset Green Home – be environmentally aware when using your phone. For details of our

ECO DECT products, visit www.gigaset.com/service

Gigaset DX800A all in one, DX600A ISDN and DL500A – your perfect companion

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / introduction.fm / 24.03.11

Version 4, 16.09.2005

Further information about your phone can be found at:

www.gigaset.com/gigasetDX800A (Gigaset DX800A all in one)

www.gigaset.com/gigasetDX600A

(Gigaset DX600A ISDN)

www.gigaset.com/gigasetDL500A

(GigasetDL500A)

After purchasing your Gigaset phone, please register it at www.gigaset.com/service – this will

ensure any questions you may have or warranty services you request are dealt with even faster!

Have fun using your new phone!

User guide

This document only describes how to get started with your Gigaset phone and its key func-

tions in condensed form.

There is a detailed description of the phone and its functions and a description of its

Web configurator on the enclosed CD. You can make phone settings from the PC via the

Web configurator (the phone's Web interface).

These instructions are in PDF format. You will need Adobe® Reader® to view these docu-

ments. You can also find Adobe® Reader® on the CD or on the Internet at www.adobe.com

Please note

To change the display language, proceed as follows:

¤ Press right on the control key v.

¤ Press the following keys in sequence: *#Q3#.

¤ Press up/down on the control key quntil the correct language is selected. Then press

the right display key.

Base overview

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / overview.fm / 24.03.11

Version 4, 16.09.2005

Base overview

1 Adjust volume S = quieter; R = louder

During a call/message playback:

Handsfree/receiver volume;

When an external call is being signalled:

Ringer volume

2 Display

3 Display keys (programmable; page 47)

In the menu: Open a menu for further

functions

4 Message key (page 37)

Access to call and message lists;

Flashes: New message/call or new firmware/

new provider profile available

5 End/back key (red key)

End call, cancel function, go back one menu

level (press briefly), back to idle status (press

and hold)

6 Function keys (programmable; page 47)

7 Redial

Open redial list (page 37)

8 Handsfree key

9 Mute key

During a call: Activate/deactivate microphone

10 * key

Activate/deactivate ringer (press and hold);

Text input: Special characters table

11 Back key for answering machine

During playback: Back to the start of the

message/previous message

12 Playing back messages

Activate/deactivate message playback

13 On/off key for answering machine

Activate/deactivate answering machine

(page 42)

14 # key

For text input: Switch between upper/lower

case letters and digits

15 Control key

16 Microphone

123465

7891011 12 1314 15 16

Display icons

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / overview.fm / 24.03.11

Version 4, 16.09.2005

Display icons

Appointment entered

in calendar

Current date

·06:30

Ã 02

Mar 2010

13:52

INT 1

Calls Calendar

M T W T F S S

0 0 0 0 0 0 0

0 0 1 1 1 1 1

1 1 1 1 1 2 2

2 2 2 2 2 2 2

2 3 3

Base status

(two lines)

Current month/year

Time

Internal name

Signalling

External

call

Ú Ø

Internal

call

Answering machine

is recording

2 3 ¼ òôl ó ·06:30

Ã 02

™ 10

Ë 09

n08

ØÜ

Appointment/

anniversary

Ø¼Ú

Alarm

clock

Answering machine icon

DX600A/DX800A:

1/ 2/ 3

numbers of the activated answering machines (orange=on)

DL500A: 1 (orange) answering machine activated

Eco Mode+ activated (white),

Eco Mode+ and Eco Mode activated (green)

ò:Bluetooth activated; ô:Bluetooth headset connected;

l: Bluetooth GSM mobile phone connected

Ringer deactivated (page 49)

Replaced by ñ, when alert tone activated

Alarm switched on and wake-up time set

Number of new messages:

u In the missed alarms list

u In the SMS list (page 41) or e-mail list

u In the missed call list (page 37)

u On the network mailbox

Display in idle status (example)

Status display in the headers: The following icons are displayed dependent on the settings

and the operating status of your base:

Contents

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / SaturnIVZ.fm / 24.03.11

Version 4, 16.09.2005

Contents

Gigaset DX800A all in one, DX600A ISDN and DL500A –

your perfect companion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Base overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Display icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

First steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Checking the package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setting up the base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting the base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Gigaset DX600A ISDN, DX800A all in one:

Setting up the base – installation wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Date/time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Making calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Making an external call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Making an internal call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Ending a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Accepting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Activating/deactivating handsfree/open listening mode . . . . . . . . . . . . . . . . . . . . . . 36

Muting the base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Making calls using network services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Using lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Redial list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Call lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Opening lists with the message key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Using directories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Using the local base directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Using online telephone directories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Using the private net directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Using the Gigaset.net directory (Gigaset DX800A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Sending SMS (text messages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Writing/sending SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Receiving an SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Reading SMS, managing lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Operating the base answering machine . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Operating via the base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Activating/deactivating call screening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Operating when on the move (remote operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Contents

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / SaturnIVZ.fm / 24.03.11

Version 4, 16.09.2005

Registering Bluetooth devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using a Bluetooth headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using GSM mobile phones – Link2mobile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Setting up the base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Accessing functions and numbers quickly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Setting the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Changing the handsfree/receiver volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Setting ringers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Activating/deactivating advisory tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Changing the system PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Setting your own area code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Customer Service & Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Questions and answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Authorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Menu overview Gigaset DX800A all in one . . . . . . . . . . . . . . . . . . . . . . . . . 53

Menu overview Gigaset DX600A ISDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Menu overview Gigaset DL500A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Insert strip – labelling function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Safety precautions

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / security.fm / 24.03.11

Version 4, 16.09.2005

Safety precautions

Warning

Be sure to read this user guide and the safety precautions before using your telephone.

Explain their content and the potential hazards associated with using the telephone to your

children.

Use only the power adapter supplied, as indicated on the underside of the base.

Use only the cables supplied for fax, fixed line, ISDN, LAN and receiver connection

and connect these to the intended port only.

Using your telephone may affect nearby medical equipment. Be aware of the tech-

nical conditions in your particular environment e.g., doctor's surgery.

Do not install the phone in a bathroom or shower room. The phone is not splash-

proof.

Do not use your phone in environments with a potential explosion hazard

(e.g., paint shops).

If you give your phone to a third party, make sure you also give them the user guide.

Remove faulty telephones from use or have them repaired by our Service team,

as they could interfere with other wireless services.

Please note

u Please note that only terminals that are operated in-house (inside buildings) may be con-

nected to the analogue TAE/ISDN connections.

u Not all functions described in this user guide are available in all countries and with all pro-

viders.

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

First steps

Checking the package contents

1One base

2 One receiver to be connected to the base

3 One (coiled) cable for connecting the handset to the base

4 One power cable for connecting the base to the mains power supply

5 This quick guide

6 One CD

7 Various connection cables (device-specific):

Gigaset DX800A all in one:

– One Ethernet (LAN) cable (Cat 5 with 2 RJ45 modular jacks) for connecting

to a router (LAN/Internet) or PC

– One phone cable for connecting to the analogue fixed line

(TAE RJ45 8 pin; the outer 2 pins are in use, cable slightly flattened)

– One phone cable for connecting to the ISDN (8 pin with 2 mini western

jacks 8/8; the inner 4 pins are in use, cable slightly flattened)

– One cable for connecting a fax device to the base (6 pin with 2 mini west-

ern jacks 6/6)

21 4

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

Gigaset DX600A ISDN:

– One Ethernet (LAN) cable (Cat 5 with 2 RJ45 modular jacks) for connecting

to a router (LAN/Internet) or PC

– One phone cable for connecting to the ISDN (8 pin with 2 mini western

jacks 8/8; the inner 4 pins are in use, cable slightly flattened)

– One cable for connecting a fax device to the base

(6 pin with 2 mini western jacks 6/6)

Gigaset DL500A:

– One Ethernet (LAN) cable (Cat 5 with 2 RJ45 modular jacks) for connecting

to a router (LAN/Internet) or PC

– One phone cable for connecting to the analogue fixed line

(TAE RJ11 6 pin)

Setting up the base

The base is designed for use in dry rooms in a temperature range of +5°C to +45°C.

¤ Set up the base at a central point in the building.

The phone's feet do not usually leave any marks on surfaces. However, due to the

multitude of different varnishes and polishes used on today's furnishings, the

occurrence of marks on the surfaces cannot be completely ruled out.

Firmware updates

This user guide describes the functions of your base from firmware

version 56.00.

Whenever there are new or improved functions for your Gigaset, firmware

updates are made available for you to download to your base. If this results in

operational changes when using your base, a new version of this user guide or

the necessary amendments will be published on the Internet at

www.gigaset.com

Select the product to open the relevant product page for your base, where you

will find a link to the user guide.

Please note

If you wish to operate handsets from the base, consider the range of the base.

This is up to 300 m in unobstructed outdoor areas and up to 50 m inside build-

ings. The range is reduced when Eco Mode is activated.

Warning

u Never expose the telephone to any of the following: Heat sources, direct sun-

light or other electrical appliances.

u Protect your Gigaset from moisture, dust, corrosive liquids and fumes.

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

Connecting the base

The following diagram is an overview of all connections for your base.

The individual connections are described in detail below.

Follow the steps in the order given below:

1 Connect the receiver to the base.

2 Connect the base to the telephone network.

3 Connect the base to the mains power supply.

4 Connect the base to the router for accessing the Internet (connection via router

and modem or via router with integrated modem) and for configuring the base

via the Web configurator.

5 Connect a wire-bound headset to the base.

*) Additional device-specific connections:

6 Gigaset DX600A ISDN/DX800A all in one:

Connect the base to a fax device.

7 Gigaset DX800A all in one: You can connect a PC to the base via the second LAN

socket LAN2 (optional) – e.g., to connect the PC to the router. The base takes on

the task of a switch.

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

1. Connecting the receiver to the base

1 Insert the jack, which can be found on the longer straight end of the connection

cable, into the connection port marked with the symbol ^ on the underside of

the base.

2 Place the straight part of the cable in the cable recess provided.

3 Insert the other jack on the connection cable into the port on the receiver.

Underside of

the base

*) The LAN2 and FAX connections are not available for all devices

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

2. Connecting the base to the telephone network

1 Insert one end of the phone cable (¢ page 8) from the rear into the recess in

the housing.

Gigaset DX800A all-in-one:

– Use the 8 pin cable with 2 mini western jacks 8/8 if you want to connect the

phone to the ISDN network (

¢ page 8, cable 7c).

– Use the TAE connection cable with RJ11 jack to connect to the analogue fixed

line (

¢ page 8, cable 7b).

2 Plug the telephone cable into the port marked with the symbol ] on the un-

derside of the base.

3 Then connect the phone cable to your phone connection (3a ISDN or 3b ana-

logue fixed line).

Underside of

the base

*) The LAN2 and FAX connections are not available for all devices (¢page 10)

Your telephone automatically detects which line it is connected to. The

installation wizard will later prompt you to make the necessary settings for

the current connection (

¢ page 16).

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

3. Connecting the base to the mains power supply

1 Insert the small jack on the power cable from the rear into the recess in the

housing.

2 Plug the jack into the port marked with the symbol \ on the underside of

the base.

3 Then connect the power cable to the mains power supply.

The software of the base is loaded. After a short time, the idle display is displayed

on the base; it is in idle mode.

Now you can make calls with your base via the fixed line or ISDN, and can be

reached via your fixed line number or the main number of your ISDN connection!

The answering machine on the base is set with a pre-recorded announcement in

answer and record mode (

¢ page 42).

*) The LAN2 and FAX connections are not available for all devices (¢page 10)

Warning

u Keep the power cable plugged in at all times for operation, as the base does

not work without a mains connection.

u Use only the power and telephone cables supplied.

Gigaset DX800A all in one, DL500A:

The pin connections of telephone cables for the analogue fixed line can vary.

The correct pin connections can be found in the long user guide on the

enclosed CD.

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

4. Connecting the base with a router (Internet) or PC

For the Gigaset DX800A all in one, the connection to a router is mainly needed for

the Internet telephony VoIP (Voice over Internet Protocol). You can set up and con-

figure up to six accounts (VoIP phone numbers) from one or several VoIP provider(s)

on the base.

All variants of the base require a connection to a router for the following features

of the phone:

u You wish to be notified as soon as new software is available for your base on the

Internet and load this onto your base.

u The date and time on your base should be updated by a time server on the

Internet.

u You wish to go online with your base, i.e., use the Info Centre, display info serv-

ices or search for phone numbers in an online directory.

The base will have to be connected to a PC (via a router or directly) if you wish to

use the following features of your base:

u You wish to set up the base using its Web configurator.

u You wish to use the additional PC software, "Gigaset QuickSync over Ethernet"

to dial numbers via the PC (e.g., numbers from a PC directory) or to load images

or melodies from the PC to your base.

For Internet access you need a router connected to the Internet via a modem (this

may be integrated in the router).

Note on Gigaset DX800A all in one

u For telephony via the Internet, you need a broadband Internet connection

(e.g., DSL) with flat rate (recommended) or volume rate and a router that con-

nects your phone to the Internet. You can find a list of recommended routers

on the Internet at:

www.gigaset.com/service

From here, go to the FAQ page and select your Gigaset IP telephone. Search

for "Router", for example.

u The base has a second LAN connection which you can use, e.g., to connect

your PC to the Internet (router).

u Data protection notice: Further information about the Gigaset.net service

data saved can be found at

www.gigaset.net/privacy-policy

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

1 Guide the end of the Ethernet cable provided (Cat 5 with 2 RJ45 modular jacks)

from the rear through the recess in the housing.

2 Plug the jack on the Ethernet cable into the LAN port on the underside of

the base.

3 Then insert the second Ethernet cable plug into a LAN socket on the router.

Gigaset DX800A all in one:

You are now able to establish VoIP connections within Gigaset.net (¢ page 40).

Gigaset DL500A:

You have completed the setup for the base.

For more information see page 33, "Date/time".

*) The LAN2 and FAX connections are not available for all devices (¢page 10)

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

Gigaset DX600A ISDN, DX800A all in one:

Setting up the base – installation wizard

As soon as the phone is connected to the mains power supply, the firmware is

started. If no connections have been generated on the base yet, the installation

wizard starts. The wizard allows you to make all necessary settings for your phone.

The following message appears in the display.

Several individual wizards are combined to form the installation wizard. The indi-

vidual wizards that start on your device depend on your type of device and the con-

nections to which the device is connected. The following individual wizards are

included in the installation wizard:

1ISDN wizard

2IP wizard

3 Registration wizard

4 Connection wizard

Refer to the following table to see which of the following steps are run on your

device and connection type, and which individual wizards are started.

Note on Gigaset DX800A all in one

The phone checks which phone connection (analogue fixed line or ISDN) it is

connected to.

¤ Press the display key §Yes§ to start

installation.

Setup - Welcome

Would you like help

setting up

your phone?

No Yes

Please note

u The installation wizard only starts if no connection has been configured on

the base yet. If connections have already been configured, you can start the

VoIP and ISDN wizards (individually) via the menu.

u Use only the installation wizard on the base, but not on a registered handset.

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

Please note:

u If the installation wizard is activated, no other handset can access the Settings

menu on the base.

u To quit the installation wizard before the process is complete, press and hold the

red end key T. All changes you have already saved using

§OK§ are retained.

u To skip a setting, press left on the control key u or the display key §No§.

1. ISDN wizard: Assigning/entering the connection's MSNs

Prerequisite: You have connected the base to the ISDN telephone network.

Several numbers (MSNs) were provided by the network provider when you

received your ISDN connection confirmation. You can save up to ten numbers

(MSNs) on your base. If there is no MSN entered on your base, you can determine

the MSNs of your connection with the ISDN wizard, i.e., call them up from the

exchange (automatic MSN assignment) or enter them manually.

Connection Procedure

GigasetDX600A ISDN 1. ISDN wizard (¢ page 17)

3. Registration wizard

4. Connection wizard

GigasetDX800A all in one

for connection to ISDN and VoIP

1. ISDN wizard (

¢ page 17)

2. IP wizard

3. Registration wizard

4. Connection wizard

GigasetDX800A all in one

for connection to the analogue

fixed line and VoIP

2. IP wizard (

¢ page 20)

3. Registration wizard

4. Connection wizard

Is started on Gigaset DX600A ISDN, Gigaset DX800A all-in-one with ISDN connection.

Please note

Not every ISDN provider supports automatic MSN assignment. If this feature is

not supported, you must enter the MSNs for your connection manually.

First steps

DL500A/DX600A-ISDN/DX800A / IM-NORD EN / A31008-N3101-R201-2-SM43 / starting.fm / 24.03.11

Version 4, 16.09.2005

¤ Press the display key §Yes§ to start

installation.

¤ Press the display key §OK§ to start

automatic MSN assignment. This

process will take some time.

Detecting your ISDN phone num-

bers (MSNs)... is displayed on the

screen.

After the MSNs have been successfully

assigned, a list containing the MSNs is

displayed.

¤ Press the display key §OK§ to close the

ISDN wizard.

The display shows ISDN installation

complete.

ISDN Wizard

Start ISDN

installation wizard?

No Yes

ISDN Wizard

This wizard helps you

detect and configure

your ISDN phone -

numbers (MSNs).

ISDN Wizard

MSN Assignment

MSN1: 12345601

MSN2: 12345602

MSN3: 12345603

MSN4: 12345604

Change OK

Please note

You can change the name of the MSNs (see detailed user guide for the base on

the enclosed CD).

Page is loading ...

Gigaset DX800A all in one User guide

Brand: Gigaset

Model: DX800A all in one

Category: Mobile phones

Type: User guide

This manual is also suitable for

Download PDF

report

Gigaset DX800A all in one User guide

This manual is also suitable for

Gigaset DX800A all in one User guide

Related papers

Other documents