2. Coastal Shower Doors
  3. C 914 C 3.0

Coastal Shower Doors C 914 C 3.0, C 938 C 3.0 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Coastal Shower Doors C 914 C 3.0 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
VINYL
REPLACEMENT
SHOWER
SWEEP
CoastalShowerDoors.com
©2019 Coastal Shower Doors
Create the perfect seal that keeps water
in the shower and off the floor.
These clear, vinyl replacement sweeps keep frameless
shower doors looking brand-new, with drip rails that
drain water back into the shower instead of onto the
bathroom floor. The sweeps fit two glass sizes: 1/4”
(which also fits 3/16”) and 3/8”, with the ability to be
trimmed for an easy fit.
Door Type
Width
Height
Material
Hinged shower door
40-in
0.25-in
Vinyl
SPECIFICATIONS
VINYL REPLACEMENT SWEEP
FOR 1/4” THICK GLASS
Measure the bottom edge of your door.
A) For Pivot Doors, measure from pivot to outer edge.
B) For Hinged Doors, measure the entire width of the
bottom edge.
C) For Continuous Hinge Doors, notched side designed to
fit around continuous hinge shower door if applicable.
Step 1:
Step 4:
Install the sweep by pressing it firmly into place
along the bottom edge of the door. Make sure
to face the drip edge inward to keep the water
within the shower stall.
Notch Notch
A) Pivot Door and B) Hinged Door
C) Continuous Hinge Door
Notch Notch
Step 2:
To ensure a tight close, it mustn't be any shorter
than your measurement. A hacksaw with a 32-TPI
blade is recommended.
Cut the vinyl to fit your measurement in step 1.
A) For Pivot Doors, cut the notches off both ends.
B) For Hinged Doors, cut the notches off
both ends.
C) For Continuous Hinge Doors, determine the
notched end that will fit over the continuous
hinge. Cut the opposing end to be flush with
the end of the door.
Step 3:
Use a utility knife to deburr the edges on each end.
Create a radius on each corner of the drip edge.
Install Instructions:
Install Instructions:
Manufacturer Color
Color Finish/Family
Package Quantity
Package Contents
Clear
Clear
1
40-in/ 1/4-in thick vinyl
frameless door sweep
Door Type
Width
Height
Material
Hinged shower door
40-in
0.375-in
Vinyl
SPECIFICATIONS
VINYL REPLACEMENT SWEEP
FOR 3/8” THICK GLASS
Manufacturer Color
Color Finish/Family
Package Quantity
Package Contents
Clear
Clear
1
40-in/ 3/8-in thick vinyl
frameless door sweep
Step 2:
Cut the vinyl to fit your measurement in step 1. To ensure a
tight close, it mustn't be any shorter than your measurement.
A hacksaw with a 32-TPI blade is recommended.
Step 4:
Install the sweep by pressing it firmly into place along the
bottom edge of the door. Make sure to face the drip edge
inward to keep the water within the shower stall.
Step 3:
Use a utility knife to deburr the edges on each end.
Create a radius on each corner of the drip edge.
Step 1:
Measure the bottom edge of your door.
A) For Pivot Doors, measure from pivot to outer edge.
B) For Hinged Doors, measure the entire width of the
bottom edge.
A)
Pivot
Door
C)
Continuous
Hinge Door
B)
Hinged
Door
A)
Pivot
Door
B)
Hinged
Door
• Drip rail slopes 45º so the water is drained back into the shower
• Easily fits into the bottom of frameless shower door
• Installs in a few minutes
• 39” length, customer trims to fit
• Sold in a case of 10
• Drip rail slopes 45º so the water is drained back into the shower
• Easily fits into the bottom of frameless shower door
• Installs in a few minutes
• 39” length, customer trims to fit
• Sold in a case of 10
CoastalShowerDoors.com
/