Danfoss 6000 Series Programmable Installation guide
- Type
- Installation guide
1
Installation and Setting Instructions
Electronic Programmable and Non-Programmable Fan Coil Thermostats
HC6000 Programmable and HCT6000 Non-Programmable Heat/Cool Thermostats
Specification
Power supply: Battery powered models -
2 x AA alkaline batteries
(not re-chargeable)
24 volt powered models -
20-30 Vac, 50/60Hz
230 volt powered models -
210-250 Vac, 50/60Hz
Temperature range: Heating stage - Off-5-30°C
Cooling stage - 16-37°C-Off
Temperature accuracy: ± 0.5°C
Deadzone adjustment: 1, 2, 3 or 4°C
Change-over temperature for water sensor changeover models:
Heat-cool 16°C
Cool-heat 30°C
Voltage rating of contacts: 20-250 Vac, 50/60Hz
Current rating of contacts: 10mA - 3A resistive, 1A inductive
Switching action: Voltage free SPDT contacts,
Type 1B
Time accuracy: ± 1 minute
Memory retention: 24V & 230V models: 15 days
Battery model: 1 minute for
battery change
IP rating: IP30
Dimensions (mm): All models -
130 x 100 x 38 (W x H x D)
Control pollution situation: Degree 2
Rated impulse voltage: 2.5 KV
Ball pressure test: 75°C
Applications
HCS & HCST Models
HCM & HCMT Models
HCW & HCWT Models
HC & HCT Models
Ordering Details
Features Battery models 24 volt 230 volt
Type Code Type Code Type Code
Heat or cool operation, selectable at time of installation
No fan output HCS6100 087N705000 HCS6101 087N706000 HCS6103 087N705400
1-speed fan output HCS6100-1 087N705800 HCS6101-1 087N707200 HCS6103-1 087N706300
3-speed fan output HCS6100-3 087N705900 HCS6101-3 087N707300 HCS6103-3 087N706400
Heat or cool systems (with pipe temperature sensor changeover), for use in 2-pipe systems
1-speed fan output HCW6110-1 087N705200 HCW6111-1 087N707000 HCW6113-1087N706500
3-speed fan output HCW6110-3 087N706100 HCW6111-3 087N707500 HCW6113-3087N706600
Heat & cool systems (with auto changeover), for use in 4-pipe systems
1-speed fan output HC6110-1 087N706200 HC6111-1 087N707600 HC6113-1 087N706700
3-speed fan output HC6110-3 087N705300 HC6111-3 087N707100 HC6113-3 087N705700
NOTE: Some models are available with remote sensors. Types & codes on
application.
2
Installation
1. Thermostat Location
2. Unpacking the Thermostat
3. Separating the Wallplate
4. Fitting the Thermostat to the Wall 5. Wiring Access - Incorrect
6. Wiring Access - Correct 7. Cable Size
Max cable size
1.5mm
2
3
C/1 2 3 4
5
678910
COM OFF ON
FAN
3
FAN
2
FAN
1
ELECTRONICS
L
i
v
e
I
n
F
u
s
e
d
3
A
O
u
t
p
u
t
O
f
f
O
u
t
p
u
t
O
n
F
a
n
3
F
a
n
2
F
a
n
1
Remote
Sensor
H
C
S
A
M
o
d
e
l
s
O
n
l
y
P
o
w
e
r
S
u
p
p
l
y
S
e
e
N
o
t
e
1
L
A
N
B
H
C
S
6
0
0
0
-
3
(
3
0
0
0
0
4
/
0
2
)
SENSOR
ROOM
HCS & HCST Models with 3 speed fan
(Heat or Cool)
HCS & HCST Models with 1 speed fan
(Heat or Cool)
HCM & HCMT Models with 3 speed fan
HCW & HCWT Models with 3 speed fan
(2 pipe change-over)
HCM & HCMT Models with 1 speed fan
HCW & HCWT Models with 1 speed fan
(2 pipe change-over)
HC & HCT Models with 3 speed fan
(4 pipe auto change-over)
HC & HCT Models with 1 speed fan
(4 pipe auto change-over)
Note 1 24volt and 230volt versions only
- on 24V models connect 24Vac to terminal A & 0Vac to terminal B
- on 230V models connect 230Vac to terminals L & N
Note 2 Water temperature sensor must be positioned in main pipework, which
must be fitted with by-pass to ensure constant flow past sensor
4
Danfoss can accept no responsibilty for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also
applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
Part No: 33060 Iss: 08 01/03
Danfoss Randall Limited
Ampthill Road,
Bedford, MK42 9ER
Tel: (01234) 364621 Fax: (01234 219705
Email: [email protected]
Website: www.danfoss-randall.co.uk
Fitting the Thermostat to the Wallplate
Ensure unit is firmly in place
Removing Battery Isolation strip
(Battery Models only)
Replacing the Batteries
(Battery Models only)
DIL Switch Settings (see rear of circuit board)
ON/OFF
COMPRESSOR
DELAY ON
HEATING
THERMOSTAT
4 EVENTS
EACH DAY *
CHRONO-
PROPORTIONAL
COMPRESSOR
DELAY OFF
COOLING
THERMOSTAT
2 EVENTS EACH
DAY
ON/OFF
NOT USED
PIPE SENSOR
FITTED **
4 EVENTS EACH
DAY*
CHRONO-
PROPORTIONAL
NOT USED
PIPE SENSOR NOT
FITTED
2 EVENTS EACH
DAY
ON/OFF
COMPRESSOR
DELAY ON
NOT USED
4 EVENTS
EACH DAY*
CHRONO-
PROPORTIONAL
COMPRESSOR
DELAY OFF
NOT USED
2 EVENTS EACH
DAY
HCS Models HCM & HCW Models
HC Models
* not used on non-programmable models
** not used on HCM models**
* not used on non-programmable models * not used on non-programmable models
-
1
-
2
-
3
-
4
Danfoss 6000 Series Programmable Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Danfoss 087N644500 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Henny Penny HCS-2 Operating instructions
-
-
TECH EU-27i Owner's manual
-
-
-
Kamstrup METERTOOL HCW Installation guide
-
Honeywell HCF 82 Owner's manual
-
-
Wolf BWL-1 S Installation And Operating Instructions Manual
-
