Pelco C652M (7/99) User manual

Brand: Pelco

Model: C652M (7/99)

Category: Cassette players

Type: User manual

This manual is also suitable for

TLR2168

Time-Lapse VCR

Installation/

Operation Manual

C652M (7/99)

Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USAwww.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120

2 Pelco Manual C652M (7/99)

CONTENTS

Section Page

1.0 GENERAL ..................................................................................................5

1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE ......................6

1.2 REGULATORY NOTICES .................................................................. 8

1.3 UNPACKING INSTRUCTIONS .......................................................... 8

2.0 OVERVIEW ................................................................................................9

2.1 INTRODUCTION TO TIME-LAPSE RECORDERS ........................... 9

2.2 TLR2168 FEATURES AND FUNCTIONS ..........................................9

3.0 QUICK START .......................................................................................... 11

3.1 BASIC START ................................................................................... 11

3.2 ADDITIONAL ITEMS ........................................................................ 11

4.0 INSTALLATION .........................................................................................12

4.1 PRE-INSTALLATION CAUTIONS ..................................................... 12

4.1.1 Securing the VCR Controls ....................................................12

4.1.2 Monitor Tips ........................................................................... 12

4.2 INSTALLATION .................................................................................12

4.3 CONNECTING THE VCR TO A MULTIPLEXER ..............................14

5.0 CONTROLS ..............................................................................................15

5.1 FRONT PANEL .................................................................................15

5.2 FLUORESCENT DISPLAY ...............................................................16

5.3 REAR PANEL ...................................................................................17

6.0 PROGRAMMING ......................................................................................19

6.1 GENERAL PROGRAMMING INSTRUCTIONS ................................19

6.2 QUICK GUIDE TO TLR2168 MENU STRUCTURE .......................... 20

6.3 MAIN MENU .....................................................................................21

6.4 DISPLAY MENU ...............................................................................21

6.4.1 Display Mode .........................................................................21

6.4.2 Time Date Size ......................................................................21

6.5 TIME DATE SEARCH MENU ...........................................................22

6.6 TIMER PROGRAM MENU ...............................................................23

6.7 RECORDING SET UP MENU ..........................................................23

6.8 REAR TERMINAL MENU ................................................................. 24

6.9 MAINTENANCE MENU ....................................................................25

6.10 FIRST TIME SET UP MENU .............................................................26

6.10.1 Day and Time Display Modes ..............................................27

6.10.2 Set the Day and Time ..........................................................28

7.0 LOADING/UNLOADING/PROTECTING THE TAPE CASSETTE ............. 30

7.1 LOADING ..........................................................................................30

7.2 UNLOADING ....................................................................................30

7.3 PREVENTING ACCIDENTAL ERASURE .........................................30

8.0 RECORDING ............................................................................................31

8.1 MANUAL RECORDING ....................................................................31

8.1.1 Recording Mode ....................................................................32

8.1.2 Record Check Function .........................................................32

8.1.3 Audio Recording ....................................................................32

8.1.4 Repeat Recording ..................................................................32

8.1.4.1 Number of Tape Uses .............................................. 33

8.1.4.2 Recommended Number of Tape Uses .....................33

8.1.5 Series Recording ...................................................................34

8.1.6 One-Shot/Interval Recording .................................................34

8.1.7 Synchronous Recording ........................................................35

Pelco Manual C652M (7/99) 3

Section Page

8.2 TIMER RECORDING ........................................................................36

8.2.1 Programming Procedure ........................................................36

8.2.2 Special DW Settings ..............................................................36

8.2.3 Avoid Mistakes When Using the Timer ..................................37

8.3 ALARM RECORDING ......................................................................37

8.3.1 Alarm Recording Connection ................................................. 38

8.3.2 External Time Clock Adjustment ............................................38

8.3.3 Programming For Alarm Recording .......................................39

8.3.4 Emergency Recording ...........................................................40

8.3.5 Alarm Record Time Display ................................................... 40

8.3.5.1 Reset The Alarm Recording List ..............................40

8.4 RECORDING AFTER A POWER FAILURE ......................................40

9.0 PLAYBACK ...............................................................................................41

9.1 PLAYBACK PROCEDURE ...............................................................41

9.2 SPECIAL EFFECTS PLAYBACK ......................................................42

9.1.1 Playback Mode ......................................................................42

9.1.2 Audio Playback ......................................................................42

9.1.3 End Of Tape ........................................................................... 42

9.2.1 Shuttle Ring ........................................................................... 43

9.2.2 Direct Shuttle Ring .................................................................43

9.2.3 Still Picture .............................................................................44

9.2.4 Frame-by-Frame Playback ....................................................44

9.3 LOCATING THE START OF ALARM RECORDINGS .......................44

9.3.1 Index Search ..........................................................................44

9.3.2 Skip Search ........................................................................... 45

9.4 ADJUSTMENT DURING PLAYBACK ...............................................45

9.4.1 Tracking Adjustment .............................................................. 45

9.4.2 Picture Quality Adjustment.....................................................46

9.4.3 Vertical Adjustment ................................................................ 46

10.0 ADDITIONAL FUNCTIONS AND FEATURES .......................................... 47

10.1 COUNTER ........................................................................................47

10.1.1 Counter Memory ..................................................................47

10.1.2 Tape Counter .......................................................................47

10.1.3 Counter Reset ......................................................................47

10.2 MEMORY BACKUP IN CASE OF POWER FAILURE ......................47

10.3 POWER FAILURE TIME DISPLAY ................................................... 47

10.4 ELAPSED TIME DISPLAY ................................................................ 48

11.0 TESTING .................................................................................................. 49

11.1 INITIAL SYSTEM TESTING .............................................................49

11.2 REGULAR SYSTEM TESTING ........................................................49

12.0 TROUBLESHOOTING ..............................................................................50

12.1 SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY ........... 50

12.2 BEFORE CALLING FOR SERVICE .................................................51

13.0 SPECIFICATIONS .................................................................................... 52

14.0 WARRANTY AND RETURN INFORMATION ...........................................54

4 Pelco Manual C652M (7/99)

REVISION HISTORY

Manual # Date Comments

C652M 12/98 Original version.

7/99 Removed material on optional remote control.

LIST OF ILLUSTRATIONS

Figure Page

1 Typical System Setup .......................................................................13

2 Connecting VCR To Multiplexer ........................................................ 14

3 Front View .........................................................................................15

4 Fluorescent Display ..........................................................................16

5 Rear View .........................................................................................17

6 Not Used

7 Menu Tree .........................................................................................20

8 Main Menu ........................................................................................21

9 Display Menu ....................................................................................21

10 Time Date Search Menu ...................................................................22

11 Timer Program Illustration.................................................................23

12 Recording Set Up Menu ...................................................................23

13 Rear Terminal Menu ..........................................................................24

14 Maintenance Menu ...........................................................................25

15 First Time Set Up Menu ....................................................................26

16 Display Mode 1 .................................................................................27

17 Display Mode 2 .................................................................................27

18 Manual Recording Steps ..................................................................31

19 Connecting VCRs in Series ..............................................................34

20 Synchronous Recording Sequence ..................................................35

21 Connection for Synchronous Recording ..........................................35

22 Switching From Normal To Alarm Mode And Back ...........................37

23 Alarm Recording Connection ............................................................38

24 Time Clock Adjustment Connection ..................................................38

25 Playback Controls .............................................................................41

26 SHUTTLE Ring Speed Settings ........................................................43

27 Direct SHUTTLE Ring Speed Settings .............................................43

28 Index Searching ................................................................................44

29 Skip Searching ..................................................................................45

30 Tracking Adjustment .........................................................................45

31 Picture Quality Adjustment ................................................................46

32 Vertical Picture Adjustment ...............................................................46

LIST OF TABLES

Table Page

A Not Used

B Call Out/Tape End ............................................................................. 24

C Recording Times in Hours ................................................................ 32

D When Tape End is Reached ............................................................. 32

E Recommended Number of Tape Uses .............................................. 33

F Numbers of VCRs and Cameras ...................................................... 36

G Timer Recording Troubleshooting .....................................................37

H Audio Playback Availability ............................................................... 42

I End of Tape Actions .......................................................................... 42

J Warning Display and Actions ............................................................ 50

Pelco Manual C652M (7/99) 5

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated

dangerous voltage within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the equipment.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO

NOT EXPOSE THIS EQUIPMENT TO RAIN OR

MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK DO NOT USE

THE POLARIZED PLUG WITH AN EXTENSION

CORD, RECEPTACLE OR OTHER OUTLET

UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE EXPOSURE.

AVERTISSEMENT

DANGER D’ÉLECTROCUTION

NE PAS OUVRIR

AVERTISSEMENT: POUR ÉLIMINER TOUT RISQUE

D’ÉLECTROCUTION, NE PAS OUVRIR LE

COUVERCLE (OU LA PARTIE ARRIÈRE).

AUCUNE PIECE RÉPARABLE PAR

L’UTILISATEUR NE SE TROUVE À

L’INTÉRIEUR. POUR TOUTE

INTERVENTION D’ENTRETIEN OU DE

RÉPARATION SE CONFIER AUX

TECHNICIENS QUALIFIÉS.

La flèche symbolisant l’éclair dans un triangle

équilateral a pour objet de tirer l’attention de

l’utilisateur sur le fait, qu’il y a des tensions

dangereuses non-isolées à l’intérieur de l’enceinte

du produit qui peuvent être suffisamment impor-

tantes pour conduire au risque d’électrocution.

Le point d’exclamation au sein d’un triangle

équilateral a pour objet de tirer l’attention de

l’utilisateur sur le fait qu’il y a des instructions de

mise en service et d’entretien (de réparation) dans

les fiches descriptives de l’appareil qui doivent

obligatoirement être respectées.

AVERTISSEMENT:

AFIN D’ÉVITER TOUT RISQUE D’INCENDIE

OU D’ÉLECTROCUTION, NE PAS EXPOSER

CET APPAREIL À LA PLUIE NI À

L’HUMIDITÉ.

ATTENTION:

POUR PRÉVENIR LES CHOCS

ÉLECTRIQUES NE PAS UTILISER CETTE

FICHE POLARISÉE AVEC UN

PROLONGATEUR, UNE PRISE DE COURANT

OU UNE AUTRE SORTIE DE COURANT,

SAUF SI LES LAMES PEUVENT ÊTRE

INSÉRÉES À FOND SANS EN LAISSER

AUCUNE PARTIE À DÉCOUVERT.

1.0 GENERAL

6 Pelco Manual C652M (7/99)

1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE

Observe the following WARNINGS before installing and using this product. Follow

all warnings and instructions marked on the VCR.

Instructions

Read all the safety and operating instructions before operating the VCR. Keep the

instructions for future reference. Follow all operating and use instructions. Heed all

warnings on the equipment and in the operating instructions.

Installation/Servicing

Installation and servicing should be done by qualified service personnel only and

conform to all local codes. Do not try to service this VCR yourself. Opening or

removing covers may expose you to dangerous voltage or other hazards.

Damage Requiring Service

Unplug the VCR from the wall outlet and refer servicing to qualified service person-

nel under the following conditions:

1. When the power cord or plug is damaged.

2. If liquid has been spilled, or objects have fallen into the VCR.

3. If the VCR does not operate normally when following the operating instruc-

tions.

Adjust only those controls covered by the operating instructions. Improper

adjustment of other controls may cause damage and will often require exten-

sive work by a qualified technician to restore the VCR to normal operation.

4. If the VCR was dropped or the cabinet damaged.

5. When the VCR shows a distinct change in performance—this indicates a need

for service.

Replacement Parts

Be sure the service technician uses only replacement parts Pelco recommends, or

which have the same characteristics as the original part. Unauthorized substitu-

tions may cause fire, electric shock, or other hazards.

Safety Check

Upon completion of any service or repair to the VCR, ask the service technician to

perform safety checks to determine whether it is in safe operating condition.

Water/Moisture/Condensation

Do not use this VCR near water. It is designed for indoor use only and must not be

installed where exposed to rain and moisture.

Do not place objects containing water, such as drinks, on top of the VCR.

If the VCR is exposed to a rapid increase in temperature (such as warming a cold

room or after moving it from a cold location to a warm one), condensation may form

on the tape transport mechanism inside the VCR. To prevent damage to the VCR

or tapes, plug the VCR into the AC outlet and turn the power on for about two hours.

Do not play back or record on the VCR during this time.

Condensation is likely to occur when:

1. The VCR is moved from a cold room to a warm room or from outdoors to

indoors.

2. A cold room is heated quickly.

3. The humidity is very high.

Avoid using the VCR where cold air (such as from an air conditioner) will blow

directly on it.

Pelco Manual C652M (7/99) 7

Cleaning

Unplug the VCR from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Clean with a soft cloth slightly moistened with mild detergent and water.

Wipe dry. NEVER USE PETROLEUM-BASED SOLUTIONS.

Attachments

Do not use attachments not recommended by Pelco as they may cause hazards.

Accessories

Do not place the VCR on an unstable cart, stand, tripod, bracket, or table. The VCR

may fall, seriously injuring a person or damaging the equipment. Use only with a

cart, stand, tripod, bracket, or table recommended by Pelco, or sold with the VCR.

Follow Pelco’s instructions when mounting equipment, and use a mounting acces-

sory recommended by Pelco.

Use care when moving equipment on a cart. Quick stops, excessive force, and

uneven surfaces may overturn the VCR and cart combination.

Do Not Place Anything Heavy On The VCR

Heavy objects placed on the VCR will cause damage.

Ventilation

Slots and openings in the cabinet provide ventilation and ensure reliable operation

of the VCR and protect it from overheating. Do not block or cover these openings.

Never place the VCR near or over a radiator or heat register. Do not place it in a

built-in installation such as a rack unless proper ventilation is provided or Pelco’s

instructions have been followed. There are many ventilation holes on the bottom of

the VCR—for maximum ventilation, place it on a hard level surface only.

Power Sources

Operate this VCR only from the type of power source indicated on the marking

label. If you are unsure of the type of power supply, consult your equipment dealer

or local power company.

Grounding or Polarization

This VCR is equipped with a three-wire grounding-type plug—a plug having a third

(grounding) pin. This plug only fits into a grounding-type outlet. This is a safety

feature. If you cannot insert the plug into the outlet, contact an electrician to replace

the obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

Power Cord Protection

Do not damage the power cord; it may cause fire or shock hazard. Route the power

cord so it is not likely to be walked on or pinched by items placed on or against it.

Pay particular attention to the cord at the wall plug or convenience receptacle and

the point where it connects to the VCR. When unplugging the power cord, grasp

the plug and remove it carefully.

Lightning/Power Surges

Unplug the VCR from the wall outlet for its added protection during a lightning

storm or when it is unused for long periods. This prevents damage to the VCR from

lightning and power line surges. Pelco recommends using conditioned-output

uninterruptible power supplies (UPS) and/or surge protected outlets to maximize

protection of the VCR.

When Not In Use

When you finish operating the VCR, always unload the cassette and turn off the

power.

Overloading

Do not overload wall outlets and extension cords as this increases the risk of fire

and electric shock.

Object and Liquid Entry

Never push objects of any kind into the VCR through openings. They may touch

dangerous voltage points or short out parts that could result in a fire or electric

shock. It can also cause extensive damage to the mechanism. Never spill liquid of

any kind on the VCR.

WARNING:

The in-

cluded power cord is

used for 120 VAC, 60

Hz. Never connect to

any outlet or power sup-

ply having a different

voltage or frequency.

8 Pelco Manual C652M (7/99)

Care Of Video Cassette Tape

1. Avoid violent vibration or shock.

2. Do not place near a strong magnetic field (near a motor, transformer, or magnet).

3. Never place or store in direct sunlight.

4. Avoid dusty places.

5. Place the cassette in the cassette case and store vertically.

6. Never store tapes in a high humidity location.

1.2 REGULATORY NOTICES

NOTE: This equipment has been tested and found to comply with the limits of a

Class B digital device, pursuant to part 15 of the FCC rules. These limits are de-

signed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However there is no guarantee that

the interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try and cor-

rect the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for com-

pliance could void the user’s authority to operate the equipment.

INFORMATION

This Class B digital apparatus meets all requirements of the Canadian Interference

Causing Equipment Regulations.

INFORMATION

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilleur du Canada.

1.3 UNPACKING INSTRUCTIONS

Unpack and inspect all parts carefully.

Be sure to save the shipping carton, boxes and inserts. They are the safest mate-

rial in which to make future shipments.

If an item appears to have been damaged in shipment, replace it properly in its box

and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replacement.

(International customers fax 1-559-348-1120 for authorization and instructions.)

If an item needs to be returned to the factory for repair, consult the WARRANTY

AND RETURN section of this manual for instructions.

Pelco Manual C652M (7/99) 9

2.0 OVERVIEW

2.1 INTRODUCTION TO TIME-LAPSE RECORDERS

Time-lapse recording permits longer than ordinary recording times. The primary

reason for using time-lapse recording in a CCTV security system is that a single

VCR tape can be used for an extended period of time beyond the standard record-

ing time. The following explains how time-lapse recording works.

The actual recording on VCRs is a series of still pictures or fields. Standard con-

sumer VHS recorders store 60 fields (30 frames) per second. A T-120 cassette

lasts just two hours in this mode (SP mode). You can get slightly longer recording

times (six hours) using the extended recording mode (EP mode). You can record

even longer on a T-160 cassette in these modes: two hours and 40 minutes in SP

mode and eight hours in EP mode. (Refer to the table in Section 8.1.1 for actual

recording times in different modes.)

Time-lapse VCRs, however, use microprocessor-based techniques to record fewer

fields per second than a normal VHS machine and extend recording time. This

negates the need to change the tape every two hours—and also substantially re-

duces viewing time when the recording is played back, another important consider-

ation.

In normal VCR operation, all video head scans (60 per second) are recorded. But in

time-lapse mode the tape runs more slowly and records pictures periodically. In 12-

hour mode, a normal time-lapse machine records 10 fields per second, and in 24-

hour mode, it stores just five fields per second (for up to 12 and 24 hours on a tape,

respectively). Longer times are possible by slowing the recording rate further.

At normal speed a picture is recorded every 1/60 of a second so there is little

change over five frames. In longer time-lapse modes, however, a field is recorded

intermittently over a longer period of time so changes are apparent from field to

field.

The time-lapse recording can be played back at normal two-hour tape speed, which

makes for rapid review—one of the time-lapse recorder’s most important advan-

tages. Action on the tape, however, appears faster than normal.

As an advanced feature, time-lapse recorders (like the TLR2168) can automati-

cally switch from time-lapse to real-time recording when an alarm condition occurs.

This is important since the primary purpose of recording an event is identification,

and real-time recording provides more detail.

2.2 TLR2168 FEATURES AND FUNCTIONS

The TLR2168 time-lapse video recorder is a powerful surveillance tool designed

for industrial and security recording. In addition to ordinary two-hour (SP – standard

play) and six-hour (EP – extended play) recording modes, its time-lapse modes

permit recording of 18, 24, 48, 72, 96, 120, or 168 hours. (Linear modes are desig-

nated as L18H and L24H.) You can extend recording up to 64,800 hours (for T-120

tape) using one-shot recording with a three-minute time interval. The TLR2168

features frame-by-frame playback and high-speed playback of longer recordings. It

is a six-head machine that can play back tapes recorded on virtually any VCR.

Audio Recording–Audio recorded in 2H, 6H, or L(inear)18H, L24H mode is played

back only in its respective mode.

Resolution And Image Quality–This VCR has a high-quality circuit allowing more

than 330 lines in B/W (black and white) mode, and more than 300 lines in color

mode.

10 Pelco Manual C652M (7/99)

High Density Recording - H·D<EP>–High density recording records three times

more fields than normal density (SP). It reduces the time interval between pictures

and makes for smoother time-lapse recording.

Tape Remaining Indicator–A bar indicator shows how much tape is left and/or

that the tape has approximately three minutes (in 2H mode) left.

Automatic Head Cleaning–The VCR automatically removes foreign matter from

the heads when a cassette is inserted for continuous smooth operation.

Easy Setup Using A Monitor–The on-screen menus simplify setup programming.

You can select these menus even without inputting a video signal.

Easy Cueing With Alarm Recording–Index signals are automatically added at

the beginning of alarm recording for easy cueing. You can confirm alarm starting

time in the playback video on the monitor or in the alarm list on the Maintenance

menu.

Time And Date Search System–You can search for a specific hour/minute and

date to accurately locate an image on tape.

External Time Clock Adjustment–You can reset the on-screen clock to the near-

est hour by applying a signal to the RST (reset) IN terminal at the rear of the VCR.

Record Check–You can confirm correct recording by pressing the PLAY button

during recording.

Automatic Head Azimuth Selection–The VCR can automatically select playback

heads for normal VHS-compatible time-lapse recordings, or older time-lapse re-

cordings made using two same-azimuth video heads. Same-azimuth time-lapse

recordings use VHS cassettes but cannot be played normally by VHS-compatible

VCRs.

Special Playback Features–These include still images, speed search, reverse

playback, frame-by-frame viewing in both directions, slow-motion, and high-speed

viewing.

JOG Dial/SHUTTLE Ring–You can use these controls to search for the desired

image. You can adjust the playback speed with the SHUTTLE ring and search for

an image frame-by-frame with the JOG dial.

Recording Options–This versatile system offers a variety of recording options,

including daily and weekly timer recording, repeat, and alarm recording.

Protection Against Power Failures—Recording data (including date, time, and

timer setup) is stored in backup memory, so the system can resume recording after

a power failure. The monitor displays the time of the failure.

Digital <ELAPSED TIME> Display–The elapsed time of recording and playback is

stored in non-volatile memory. You can use the elapsed time display as a guide to

when to do periodic maintenance.

Tape Use Counter–This counter displays how many times you have recorded on a

tape. This helps you decide when you need to replace a tape.

Daylight Saving Time Setting–A daylight saving time setting is available. You can

set the clock forward an hour by programming the menu.

NOTE:

The battery backup is for

memory only–the VCR does not

continue recording if the power

goes out. If you want to keep re-

cording during an outage, make

sure the VCR system is on your

UPS (uninterruptible power supply)

system.

Pelco Manual C652M (7/99) 11

3.0 QUICK START

3.1 BASIC START

1. Decide where to locate the VCR. Do all system hookups first (camera, multi-

plexer, etc.) if you are installing the VCR in a location where you cannot ac-

cess its rear panel.

2. Connect the VCR to other equipment (Sections 4.2 and 4.3).

3. Plug in the VCR and press the POWER button. You should see the time and

date displayed on the monitor.

4. To reset the time/date (First Time Set Up menu), see Section 6.10.2. Skip if

you do not want to reset the time/date.

5. Put in a T-120 or T-160 tape. Refer to Table C for recording times. Set the

appropriate tape length if you want the approximate tape remaining indicator

to work correctly (Section 6.10.2). If not, skip.

6. Put the VCR in the recording mode you want by pressing the REC/PLAY (+)

and (-) buttons. Watch the fluorescent display. Set to 2H, L24H, 48H – 168H,

or 0H mode for recording at SP speed. Set to 6H, L18H, 48H – 168H, or 0H for

EP speed.

7. Press REC to begin recording.

8. Press STOP to stop. Turn the SHUTTLE ring right to fast forward and left to

rewind. Press PLAY to play back the tape.

9. Refer to Section 11.1 for initial system testing information.

3.2 ADDITIONAL ITEMS

You can also incorporate the following programming steps for more than a basic

quick setup.

1. If desired, set the tape end, quasi v-sync, playback head select, and buzzer

options (Section 6.10) on the First Time Set Up menu.

2. If desired, set the display mode and time/date size options (Section 6.4) in the

Display menu.

3. If desired, in the Timer Program menu (Section 6.6), program for timer record-

ing (Section 8.2 ).

4. If desired, in the Recording Set Up menu (Section 6.7), program for alarm

recording mode and duration (Section 8.3.3), emergency recording (Section

8.3.4), and one-shot recording (Section 8.1.6).

5. If desired, in the Rear Terminal menu (Section 6.8), program for call out (Sec-

tion 8.1.5 for series recording), clock out (Section 8.1.7 for synchronous re-

cording), operation of the mode out terminal, and operation mode of the REC

IN terminal.

NOTE:

This section is intended for

people experienced in working with

time-lapse recorders and installing

CCTV systems.

12 Pelco Manual C652M (7/99)

4.0 INSTALLATION

4.1 PRE-INSTALLATION CAUTIONS

1. Provide secure power to system components. Prevent overloading or short-

ing by dedicating power circuits to the surveillance equipment. Restrict ac-

cess to the surveillance system circuit breakers, switches, and equipment power

cords.

2. Surveillance system components must be operationally compatible. Time-lapse

recording speeds and dwell times of any accessory switching equipment must

be compatible with each other.

3. The TLR2168 time-lapse VCR provides several alarm recording speeds so it

is important that alarm triggering of components be operationally compatible.

Refer to Section 2.1 for information on time-lapse recording.

4. Complete all system hookups (camera, multiplexer, etc.) before installing the

VCR in a location where you cannot access its rear panel.

4.1.1 Securing the VCR Controls

Protect surveillance equipment to forestall tampering. We recommend putting the

recorder in a secure VCR cabinet. Pelco offers such units–the RM2000, which is a

rack kit for a single VCR, and the RM2004, which is a rack kit for four VCRs.

4.1.2 Monitor Tips

• Pelco recommends using a CCTV monitor.

• Some monitors may cause picture vibration or picture distortion at the top or

bottom of the image during still or normal playback. (Refer to Section 9.4.3 for

information.)

A television may be unable to provide a stable picture without vibration or distortion.

4.2 INSTALLATION

1. Remove the VCR and all cables from the box.

2. Place the VCR in a suitable location.

• If the location is unsecured, refer to Section 4.1.1 for information about

products to lock up the VCR.

• Do all system hookups (camera, multiplexer, etc.) before installing the

VCR in a location where you cannot access its rear panel,

3. If installing in a rack, place the VCR in the rack before making cable and

power connections. Refer to the documentation included with the rack kit for

specific installation instructions.

4. If you are not using a switcher, refer to Figure 1.

• Connect the camera (video output) to the rear of the VCR (video input

BNC). Connect the VCR (video output BNC) to the monitor (video input).

• Connect the alarm input to the VCR (SET IN and GND [ground] termi-

nals).

• If you are using a 600Ω microphone, connect it to the VCR (MIC IN jack).

Connect the VCR (audio output connector) to the monitor (audio input).

5. If you are using a switcher, refer to Section 4.3.

Pelco Manual C652M (7/99) 13

Figure 1. Typical System Setup

AUDIO

OUT

MIC IN

VIDEO OUTPUT

FROM CAMERA

VIDEO IN

AUDIO IN

MONITOR

VIDEO

OUT

CCTV

CAMERA

VIDEO

MIC

600 Ω

VIDEO

OUTIN

OUTMIC

AUDIO

RESET

REMOTE

SET RST

REC GND ALM MODE CLK CALL

OUT

AUDIO IN

ALARM OUTPUT

FROM DEVICE

SET

ALARM DEVICE

14 Pelco Manual C652M (7/99)

Figure 2. Connecting VCR To Multiplexer

VCR

AUX

MAIN

SPOT

SVHS

OUT IN

SVHS

IN COM OUT

120 VAC 60 Hz

ALARMS

1 2 3 4 5 67 8 91011 14151612 13

MX4000 GENEX™ SERIES MULTIPLEXER

TIME-LAPSE VCR

REMOTE

RESET

GND

CLK

AUDIO

VIDEO

IN OUT

CALL

OUT

MIC

ALM

RECSET RST

MODE

COAXIAL CABLE

4.3 CONNECTING THE VCR TO A MULTIPLEXER

Figure 2 shows how to connect the VCR to an MX4000 Series Genex™ Multi-

plexer.

For Automatic Speed Tracking (“B” lines in Figure 2)

This lets the VCR control the multiplexer’s recording speed. It

is the most efficient recording method.

1. Connect the VCR’s CLK output to the multiplexer’s head

switching (HS) input to synchronize camera switching.

2. Connect the multiplexer’s ground terminal to the VCR’s

GND terminal.

For Alarm Recording (“A” lines in Figure 2)

This is to start and stop recording when there are alarms.

1. Connect the multiplexer’s normally open (NO) relay ter-

minal to the VCR’s SET IN (alarm input) terminal.

2. Connect the multiplexer’s common C terminal to the VCR’s

GND terminal.

NOTE:

Cameras and monitors are connected to the multiplexer. Figure 2 shows the connection between the VCR

and an MX4000 Series Genex™ Multiplexer. Refer to the multiplexer manual for additional component connections.

Pelco Manual C652M (7/99) 15

Figure 3. Front View

5.0 CONTROLS

5.1 FRONT PANEL

1. POWER button

Press for on; press again for off. The POWER indicator

illuminates when the VCR is turned on.

2. EJECT button

Press to remove the cassette.

3. Cassette loading slot

Insert the cassette in this slot to load it.

4. STOP button

Press to halt all tape-related functions.

5. REC (record) button

Press to begin recording.

6. JOG dial

Use to advance the tape frame-by-frame and to program

the menus.

7. SHUTTLE ring

Use to adjust the playback speed and to program the

menus. Turn this ring to the right to advance the tape or to

forward search. Turn it to the left to rewind a tape or to

reverse search. You can also use it to clear the alarm list,

power loss list, and timer recording. It also lets you pro-

gram or exit the menus after setup.

8. PLAY button

Press to play back a previously recorded tape.

9. PAUSE/SHUTTLE HOLD button

Press this button during recording to temporarily stop tape

movement. Press again to resume recording. When it is

pressed during playback, tape movement stops and a still

field is displayed. Press again to restore normal playback.

Pressing and holding this button after turning the SHUTTLE

ring allows continuous high-speed playback even if the

SHUTTLE ring is released.

10.COUNTER MEMORY/SKIP/INDEX button

Press this button to switch among counter memory (fluo-

rescent display shows M), skip search (displays SKIP),

and index search (displays INDEX).

• Counter Memory: Turn the SHUTTLE ring to the right

and the tape rewinds to the 00000 counter position

and stops (Section 10.1.1).

• Skip Search: The VCR fast forwards or rewinds until

it locates an index signal and then plays back for

about four seconds in 2H or 6H mode, doing this until

it reaches the end or beginning of the tape (Section

9.3.2 ).

• Index Search: During fast forward or rewind, the VCR

searches for alarm index signals. When it finds one,

the VCR plays back the tape and stays in still mode

(Section 9.3.1).

11. TIMER REC button

Press to make a timed recording.

12. REC/PLAY MODE buttons

• Set to 2H, L24H, 48H - 168H, or 0H mode to set the

recording speed in SP (standard play) mode. Set to

2H, L24H, 24H, 48H - 168H, or 0H mode to set the

playback speed in SP mode.

• Set to 6H, L18H, 48H - 168H, or 0H mode to set the

recording speed in EP (extended play) mode. Set to

6H, L18H, 48H - 168H, or 0H mode to set the play-

back speed in EP mode.

13. COUNTER RESET button

Press to reset the counter to 00000.

14. DISPLAY button

Press to display the Main menu. Press again to show

the time display.

15. POSITION/VERTICAL ADJUST buttons (+/-)

• Pressing the (+) button moves the day and time dis-

play to the right. Pressing the (-) button moves the

day and time display down the screen. The display

cannot be adjusted if a warning is displayed.

• Pressing either button minimizes vertical jitter in the

still mode or during fast playback. Refer to Section

9.4.3 for details.

16. TRACKING buttons (+/-)

Press these buttons if noise is present during playback,

reverse playback, or slow playback.

17. PICTURE control

Use this control to adjust picture quality between soft and

sharp.

18. VIDEO switch

Use the switch to select color or black and white re-

cording and playback.

REW

JOG/ADJUST

CLEAR/ ENTER/

SHUTTLE

REC

STOP

PLAY

POWER

EJECT

PICTURE

TRACKING

POSITION/

VERTICAL

ADJUST

REC/PLAY

MODE

COUNTER

RESET

COUNTER MEMORY/

SKIP/INDEX

PAUSE/

SHUTTLE HOLD

DISPLAY

TIMER REC

VIDEO

SOFT

SHARP

COLOR

B/W

FLUORESCENT DISPLAY

1517

16 Pelco Manual C652M (7/99)

1. M (counter memory) indicator

Illuminates during rewind for counter memory mode.

2. PL (power loss) indicator

Illuminates when there is a power failure during record-

ing.

3. ALARM indicator

Flashes during alarm recording and stays on when the

alarm recording is finished.

4. INDEX indicator

Flashes during recording of the date/hour index at the

change of the hour, and during recording of the alarm

index signal. It lights during an index search.

5. MODE display

Displays the selected recording or playback mode. Dur-

ing an index search, it displays the index number. It will

also indicate the playback head selection—SH or AH—

three seconds after the playback starts or if the playback

mode is changed. In the First Time Set Up menu, if the

PB HEAD selection is set to L/L or R/R, then SH will be

illuminated. If set to AUTO, then AH will be illuminated.

(Refer to “PB HEAD SELECT” in Section 6.10 for more

information.)

NOTE:

SH or AH lights during playback in SP mode ONLY.

6. SKIP indicator

Illuminates during skip search.

7. Record mode indicator

EP illuminated means the VCR is either recording or play-

ing back a tape recorded in EP mode. SP means the

same, but for SP mode.

Figure 4. Fluorescent Display

5.2 FLUORESCENT DISPLAY

8. Repeat indicator

Illuminated when TAPE END in the First Time Set Up menu

is set to REPEAT or ALARM•PROT.

9. Cassette status indicator

Illuminates when you insert the tape. The light advances,

stops, or flashes corresponding to the movement of the

tape.

10. Timer recording indicator

Illuminates when the TIMER REC button is set to ON.

11. Tape remaining indicator

Indicates the approximate tape position (S = start, E =

end).

12. REC indicator

Illuminates during recording.

13. PLAY indicator

Illuminates during playback.

14. EMGCY (emergency recording) indicator

Illuminates when EMERGENCY REC in the Recording Set

Up menu is set to ON.

15. LOCK indicator

Illuminates when the lock feature is in use.

16. Counter display

Indicates the relative position of the tape.

PLAY

EMGCY

SKIP

LOCK

M PL

SP EP

ALARM

INDEX

MODE

REC

Pelco Manual C652M (7/99) 17

Figure 5. Rear View

5.3 REAR PANEL

1. AC power socket

The power cord plugs into this socket. Insert the cord firmly.

2. SET IN terminal

(Alarm) input terminal to start alarm recording. Connect the

alarm sensor here.

3. RST (reset) IN terminal

Input terminal to stop alarm recording when ALARM REC

DURATION in the Recording Set Up menu is set to MAN1.

Connect the alarm reset switch here. You can also use this

terminal to set the on-screen clock when set to any mode

other than MAN1.

4. REC IN terminal

Input terminal to start/stop recording. You can also use this

terminal for series recording (refer to Section 8.1.5) or syn-

chronous recording (refer to Section 8.1.7).

5. GND (ground) OUT terminal

Connect the ground lead here when a lead connected to

other terminals requires a ground.

6. ALM (alarm) OUT terminal

Output terminal to an external device to indicate an alarm is

being recorded.

7. MODE OUT terminal

Output terminal to indicate the VCR’s mode of operation,

which can be selected by setting the MODE OUT in the Rear

Terminal menu.

8. CLK (clock) OUT terminal

Output terminal to control an external camera switcher,

such as the MX4000 Series Genex™ Multiplexer.

9. CALL OUT terminal

Output terminal to indicate when the tape finishes record-

ing or that there was a problem during recording.

10. RESET button

Press to erase the present time, alarm recording list, power

loss list, and the number of tape uses. Power to the VCR

is cut off while the button is pressed. If there is a tape in

the VCR and the button is released, the power indicator

will light and the tape will fast forward for a few seconds.

The VCR will then turn off.

11. REMOTE jack

The remote control unit is not supplied.

12. VIDEO OUT connector

Output connector for video signal (BNC connector).

13. VIDEO IN connector

Input connector for video signal (BNC connector).

14. AUDIO OUT connector

Audio output connector (RCA pin).

15. AUDIO IN connector

Audio input connector (RCA pin).

16. MIC IN jack

Input jack for a microphone rated at 600-ohms impedance.

NOTE:

Make sure the power cord is unplugged before making any rear terminal connections.

WARNING:

The included power cord is used for 120 VAC, 60 Hz. Never connect the power cord to any

outlet or power supply having a different voltage or frequency.

VIDEO

OUTIN

OUTÉMIC

AUDIO

RESET

REMOTE

SET RST

REC GND ALM MODE CLK CALL

OUT

18 Pelco Manual C652M (7/99)

(This page intentionally left blank.)

Pelco Manual C652M (7/99) 19

6.0 PROGRAMMING

6.1 GENERAL PROGRAMMING INSTRUCTIONS

The following is a universal procedure that shows how programming is done on the

VCR. Use the JOG dial to select items, the SHUTTLE ring to the right to enter,

and SHUTTLE ring to the left to exit.

1. Press the DISPLAY button. The Main menu is displayed.

2. Turn the JOG dial to select the desired item.

• Turn it to the right to move the cursor downward.

• Turn it to the left to move the cursor upward.

3. Turn the SHUTTLE ring to the right. The desired item is selected and the

menu will appear.

4. Turn the JOG dial to select an item.

5. Turn the SHUTTLE ring to the right. The item will flash.

6. Turn the JOG dial to change the setting.

7. Turn the SHUTTLE ring to the right to enter.

8. Press the DISPLAY button. The present time display will appear.

NOTE:

If the VCR is connected to

an MX4000 Series Genex™ Multi-

plexer, make sure the multiplexer is

in the VCR mode and single-

camera display. Momentarily press

the VIEW button on the multiplexer,

then press the DISPLAY button on

the VCR.

20 Pelco Manual C652M (7/99)

6.2 QUICK GUIDE TO TLR2168 MENU STRUCTURE

The operating parameters of the VCR are set through various on-screen menus.

Program your choices on the menus according to the instructions on the following

pages.

Figure 7. Menu Tree

present time

display

11 – 11 – 98 09 : 21 : 01

RECORDING SET UP

OFF

NORMAL<SP>

SHOT

MAIN MENU

DISPLAY

TIME DATE SEARCH

TIMER PROGRAM

RECORDING SET UP

REAR TERMINAL

MAINTENANCE

FIRST TIME SET UP

Use JOG to select,

and ENTER.

Press DISPLAY to exit.

ALARM REC MODE

ALARM REC DURATION

EMERGENCY REC

REC MODE

ONESHOT•FIELD

ONESHOT•INTERVAL

REAR TERMINAL

WRNG•TAPE END

REC- 1

REC

SERIES

CALL OUT

CLOCK OUT

MODE OUT

REC IN

MAINTENANCE

POWER LOSS LIST

ALARM LIST

ALL MENU INITIALIZE

POWER LOSS LIST CLEAR

ALARM LIST CLEAR

REPEAT REC TIMES

ELAPSED TIME

FIRST TIME SET UP

TAPE END

QUASI V-SYNC

TAPE LENGTH

PB HEAD SELECT

BUZZER

TIME DATE ADJUST

STOP

T-120

NORMAL

WRNG

OFF

09 :21 : 01

TIME DATE SEARCH

15:00

FORWARD

TIME

DATE

DIRECTION

Use JOG to adjust,

and ENTER.

DISPLAY

SMALL

11 – 11 – 98 09 : 21 : 01

DISPLAY MODE

TIME DATE SIZE

Ex.

MODE 1

TIMER PROGRAM

DW START END HR

SPL 08 : 40 17 : 10 L18EP

2 SAT 08 : 40 12 : 20 L18EP

3 WED 22 : 00 22 : 54 2SP

4 - - - - - : - - - - : - - - - -

5 - - - - - : - - - - : - - - - -

6 - - - - - : - - - - : - - - - -

7 - - - - - : - - - - : - - - - -

8 - - - - - : - - - - : - - - - -

SPECIAL DW MON–FRI

ALARM LIST

ALL MENU INITIALIZE

Turn the SHUTTLE RING <<

then all MENU will be

initialized.

POWER LOSS LIST CLEAR

Turn the SHUTTLE RING <<

then POWER LOSS LIST

will be cleared.

ALARM LIST CLEAR

Turn the SHUTTLE RING <<

then ALARM LIST will be

cleared.

0001 01 - 05 - 98 01 : 00

0002 01 - 07 - 98 21 : 10

0003 01 - 10 - 98 09 : 15

POWER LOSS LIST

01 01 - 03 - 98 01 : 00

DAYLIGHT SAVINGS

MONTH

DATE

YEAR

TIME

TIME DATE ADJUST

Page is loading ...

Pelco C652M (7/99) User manual

Brand: Pelco

Model: C652M (7/99)

Category: Cassette players

Type: User manual

This manual is also suitable for

Download PDF

report

Pelco C652M (7/99) User manual

This manual is also suitable for

Pelco C652M (7/99) User manual

Related papers

Other documents