Intellinet 550918 User manual

NSC10-WG

NetWork

Camera

uSer

maNual

MODEL 550918

INT-550918-UM-0709-01

2

TABLE OF CONTENTS

section page

table of CoNteNtS

1 INTRODUCTION .......................................................................... 3

1.1 System Requirements .......................................................... 3

1.2 Package Contents ................................................................ 3

2 HARDWARE ................................................................................ 4

2.1 Controls & Indicators ............................................................ 4

2.2 Installation ............................................................................ 5

3 SOFTWARE INSTALLATION ....................................................... 5

3.1 Administrator Utility .............................................................. 9

3.2 Viewer ................................................................................ 10

4 ADMINISTRATOR UTILITY OPERATION ..................................11

4.1 LAN Settings .......................................................................13

4.2 Security ...............................................................................14

5 VIEWER OPERATION ................................................................15

5.1 Viewer Controls ...................................................................15

  5.2 Conguration .......................................................................17

5.3 Changing the Display Layout ............................................. 27

6 WEB CONNECTION & SETUP .................................................. 30

6.1 Camera ..............................................................................31

6.2 LAN ................................................................................... 32

6.3 WLAN ............................................................................... 34

6.4 E-Mail & FTP ..................................................................... 36

6.5 Motion Detection ................................................................ 37

6.6 System ............................................................................... 38

6.7 Status ................................................................................. 39

6.8 Users .................................................................................. 40

6.9 Log ................................................................................... 40

7 ROUTER/GATEWAY SETUP FOR INTERNET VIEWING ..........41

8 MONITORING VIA UPnP IN WINDOWS XP ............................. 42

9 CONFIGURING WINDOWS SERVER 2003 .............................. 45

10 SPECIFICATIONS .......................................................................47

3

INTRODUCTION

1 iNtroduCtioN

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS

™

NSC10-WG Network Camera, Model 550918.

Ideal camera for home-network-based video streaming, the NSC10-WG

Network Camera can be conveniently accessed remotely over the Internet,

allowing you to save snapshots or record directly from your Web browser

to the local hard drive without installing any software or drivers.

These instructions make setup and operation quick and simple, so you’ll

soonbeenjoyingthebenetsofallthesepopularfeatures:

• Digital24-bitcolorMotion-JPEGvideo

• 300kCMOSimagesensorprovidesexcellentimagequality

• High-speedhardware-basedimagecompression

• Supports54MbpsWireless802.11gwithWEP,WPA&WPA2encryption

• Includeseasy-to-use16-channelcameraviewingandrecordingutility

• Auto-setupforfoolproofinstallation

• Supportsimageresolutionsupto640x480(VGA)

• Maximumimageframerate:25fps

• Integratedmotiondetection

• Event-triggeredFTPande-mailuploadofstillimages

•Three-Year Warranty

1.1 System Requirements

• SupportsWindows2000/XP/Vista and Windows 7

• MicrosoftInternetExplorer6.xandabove

• ActiveXcontrolinstallation

1.2 Package Contents

• NSC10-WGNetworkCamera

• Quickstartguide

• CDwithsoftwareandusermanual

• Cameramountingbracketandstand

• Poweradapter

• Networkcable(1m/3ft.)

NOTE:Somescreenimageshavebeenmodiedtottheformatof

this user manual.

4

HARDWARE

Focus ring

Antenna and reverse

SMA connector

Power LED

WLAN LED

LAN LED

2 hardWare

2.1 Controls & Indicators

The focus ring allows you to adjust the focus of the

camera simply by rotating the ring while viewing the

live image.

2.1.1 LEDs

The LEDs indicate the camera and network

status.

LAN — Lights a steady green when the camera

  isproperlylinkedtoawirednetwork;ashes

green when video is being transmitted or

received through the connected network.

WLAN — Lights a steady amber when the camera is properly linked

  toawirelessnetwork;ashesamberwhenvideoisbeingtransmitted

or received through the wireless network.

Power — Lights a steady blue when the camera is on.

2.1.2 Connectors

Connectors are located on both the top and the

bottom of the camera.

Power — Connect the included power adapter

to this jack.

LAN — Connect the Ethernet network cable to this port.

Reset — If problems occur with your camera, press the recessed Reset

  buttonwithapenciltiporsimilarpointedobject(forlessthan2 

  seconds)andthecamerawillre-bootitself,keepingyouroriginal

  congurations.Ifproblemspersistorifyouexperienceserious

  problems(orifyouforgetyourpassword),presstheResetbuttonfor

longer than 5 seconds and the camera will reset itself to the factory

default settings. WARNING: Resetting to factory defaults will erase

  anycongurationyou’vemade.

Reverse SMA connector — Attach the antenna to this connector, as

shown in the Controls & Indicators image above.

Bottom panel

5

SOFTWARE INSTALLATION

2.2 Installation

Once you’ve unpacked all the NSC10-WG Network Camera components

andveriedthatallitemsareaccountedfor(seePackageContents,

Page3):

•ConnecttheLANportofthecameratoyourswitch/routerorother 

network device using the included network cable.

•ConnectthePowerjackofthecameratoanA/Coutletusingthe

 includedpoweradapterandconrmthatthePowerLEDison.NOTE:

It’s highly recommended that you use only the power adapter that

comes with this camera.

•ConrmthatyouhavethecorrectVGAdriverandDirectX9.0orabove

installed.

3 SoftWare iNStallatioN

The Internet Camera Install Wizard utility on the included software CD

will guide you through the installation process. The procedure presented

in this manual represents Windows XP; the procedures for Windows

2000/Server 2003 and Vista are very similar.

1. Insert the included software CD in your computer’s CD-ROM drive.

  Typically,theAutorun.exeprogramrunsautomatically;ifnot,engage

it manually from the CD’s Autorun folder.

2. The Welcome screen of the wizard will display four options. Click to

select the desired option, which at this point is “Install Administrator

Utility.”

6

SOFTWARE INSTALLATION

3. The system will begin the installation procedure. When the second

  Welcomescreendisplays,click“Next”tocontinuetheinstallation.

4. To install the software program in a different location, click “Change”

  ontheChooseDestinationLocationscreen.Otherwise,click“Next”

to continue.

7

SOFTWARE INSTALLATION

5. With the Ready to Install the Program screen displayed, click “Install”

to begin installation.

6. The automatic installation procedure presents a Setup Status screen

to indicate progress.

8

SOFTWARE INSTALLATION

7. With the InstallShield Wizard Complete screen displayed, click “Finish”

to complete the Administrator utility installation.

8.Ontheinitialwelcomescreenofthewizard,click“Install16Chan(nel)

Camera Viewer.’’ The Viewer installation will automatically begin, with

steps similar to those of the Administration utility.

9

SOFTWARE INSTALLATION

3.1 Administrator Utility

The Administrator utility allows you to search for and set up cameras

located within an intranet or on the Internet. Once installed, it displays

allNSC10-WGNetworkCamerasitnds.Choosetheoneyouwantto

congureandclickontheCongureicon(circledbelow)toproceed.

When prompted with the Login screen,

enterthedefaultpassword(“1234”)and

click“OK”tologintotheIPsetup(LAN

Settings)screen.(Defaultusername:admin.)

The NSC10-WG Network Camera works

throughthenetwork(TCP/IPProtocol),sotheIPaddressandsubnet

10

SOFTWARE INSTALLATION

mask setting must be correct to access the camera. The wizard will

detect the IP address status of your network automatically and suggest

afreeIPaddressforthecamera(with“DHCP”selectedbydefault).You

can accept the suggested values or enter the values — detailed below in

4.1 LAN Settings — manually by selecting “Manual IP.” NOTE: Remember

that the subnet mask must be the same for both the camera and PC.

Eitherway,click“OK”toapplytheselectedconguration.

3.2 Viewer

Like the Admin utility, the Viewer can be activated by clicking its

desktop/quick-launch icon or by selecting “IPCam Surveillance

Software” from the Start menu’s Internet Camera folder.

ClicktheCongurebutton(thewrench,ashighlightedabove)todisplay

apopupmenuof“CongureCameras”and“GeneralOptions.”Click

“CongureCameras”todisplaythesubsequentscreen.

To assign any of the 16 cameras that can be connected simultaneously

to a particular channel for viewing, highlight the channel in the Channel

list, highlight the camera in the Camera Search list, then click “Select’’

IPCam Surveillance

Software

11

SOFTWARE INSTALLATION

and“OK.”TheViewerwilldisplaythechannelyou’vejustcongured.

Forcompletecongurationinstructions,seeSection5:ViewerOperation.

12

ADMIN UTILITY OPERATION

4 admiNiStrator utility operatioN

Besides the auto install, there are two other ways to launch the Admin

utility:

• GotoStartonthedesktopandclick/select“Programs\

 IPCamera\AdminUtility.”

• Double-clicktheIPCamAdminUtilityicononyour

 desktop(shownatright).

Once the utility is started, it will search for and list all the cameras in the

network,withspecicdetailsandadministratoroptionsasshownand

explainedbelow(andbrieyintroducedin3.1AdministratorUtility).

MAC Address, etc.—Thefourcolumnsofinformationinthiseldpresent

 detailsyoumayneedforreferenceduringconguration.

Search / Browse / Congure — These three icons at the lower-left of the

 screenallowyouto,respectively(fromlefttoright):searchforcameras

on the network; activate the browser to auto-connect to a camera to

 obtainvideo;andcongurethecamera(s)and/orchangethelogins

using the LAN Settings and Security screens.

ClicktheCongureicon(thetoolsimage)todisplaytheLoginscreen

as shown in section 3.1. The default username is “admin” the default

password is “1234.” Once the correct username and password are

entered, click “OK” to display the LAN Settings screen.

13

ADMIN UTILITY OPERATION

4.1 LAN Settings

As mentioned in 3.1 Administrator Utility, the default setting on this

screen is “DHCP,” meaning that the entries below need to be made

only when you select “Manual IP.”

IP — Enter an unused IP address within the IP address range used on

 yourLAN.Forexample,iftheIP address of your LAN is in the range

of 192.168.2.1 to 192.168.2.254, you can set an unused IP address

from that range for the camera, such as 192.168.2.250.

NetMask — This subnet entry must match the subnet setting on your

  LAN;forexample:255.255.255.0.

Gateway — This entry is used to forward frames to destinations in a

different subnet on the Internet. The Gateway setting must be the

same as the one used by the PCs on your LAN.

DNS—Thedomainnameserver(DNS)translatesnamesintoIP

addresses, and must be the ame as the one used by the PCs on your

LAN.

Web Port — The default setting is “80,” but since the Web server may

be using Port 80, you can enter a different port for the camera. If you

 changetheWebportfrom80to8080,forexample,you’llneedto

 enterhttp://192.168.2.3.8080whenconnectingtothecamerathrough

your Web browser.

14

ADMIN UTILITY OPERATION

4.2 Security

The Security screen lets you make the changes detailed below.

Camera Name — The default is “IC1500WG.” It’s suggested that you

enter a name for each camera that will provide immediate recognition

of a camera’s purpose.

New Password — If you’re changing the password for a camera, enter

 thenewpasswordinthiseld.

Conrm Password—Re-enterthenewpasswordinthiseld.

15

VIEWER OPERATION

5 vieWer operatioN

The Viewer can be activated by clicking its desktop/quick-launch icon or

by selecting “IPCam Surveillance Software” from the Start menu’s

Internet Camera folder. IMPORTANT: The Viewer software will only

workwithamonitorresolutionsettingof1024x768.Besurethisis

your setting before you use the Viewer; otherwise, it won’t start.

5.1 Viewer Controls

Video Display Area — The images from all connected cameras are

displayed in this section.

Language — Make a selection for your operating format.

Display Layout — Click on any one of the eight camera image display

 layoutstoimplementitfortheselectedcamera.(See5.3Change

 DisplayLayoutfordetails.)

Full Screen (1)—Clicktollthescreenwithonlytheimagefromthe

selected camera. Press <Esc> to quit Full Screen mode.

Scan (2) — Click to automatically cycle through the views from all

video diSplay

area

meSSaGe

diSplay box

diSplay

layout

1

2

3

4

5

7 8

9 10

1211

6

16

VIEWER OPERATION

 connectedcameras.Clickoncetoactivatethefunction(theiconturns

 blue);clickagaintostopscanning(theiconturnswhite).NOTE: If a

 cameraisconguredbutdisconnected,itwillstilldisplayinascan

 sequence:Theviewwillbeblankand“Disconnected”willappearin

the upper-left corner of the display.

Zoom Out (3) — Click to view more of what’s available in the selected

camera image. NOTE: This function is available only with cameras

that feature it.

Zoom In (4) — Click to view more details of the selected camera image.

 ItmaybenecessarytorstusethePTZcontrolstoidentifyandisolate

the part of the image you want to zoom in on. NOTE: This function is

available only with cameras that feature it.

PTZ Control (5)—Iftheconnected/selectedcamerasupportsthePTZ

 (pan-tilt-zoom)function,youcanmoveineightdirectionsbyclicking

 onthecorrespondingdirectionalarrowonthePTZcontrolring.

Home (6)—Clicktoreturntheselectedcameratothehome(default)

position. NOTE: This function is available only with cameras that

feature it.

Record (7) — Click to begin video recording from a selected camera.

 ThestartdateandtimeoftherecordingisconrmedintheMessage

 DisplayBox;forexample,“7/211:23:00,Camera4StartManual”

 (startedmanually).Likewise,themessage“7/211:25:00,Camera4

Stop Manual” would indicate the recording was manually stopped two

minutes later.

Congure (8)—Clicktocongurethecamera(s)onthenetwork.(See

 5.2Congurationfordetails.)

17

VIEWER OPERATION

Playback (9)—ClicktodisplaythePlaybackscreensoyoucanndthe

 previouslyrecordedvideoleyouwanttoview.Twosearchoptions

 arepresented:TimeSearchpresentsallvideolescreatedwithina

 speciedtimeperiod;MotionSearchpresentsallvideolescreated

 bythemotiondetectionfunctionwithinaspeciedtimeperiod.Enter/

 select“From”and“To”valuesintheappropriateelds,thenclickthe

corresponding “Search” button. All found videos corresponding to

those parameters will be displayed as a list in the window at the right.

 Highlighttheleyouwanttoviewandclick“Play.”

Snapshot (10) — Click to take a snapshot of a selected camera image.

Snapshots can be saved to a storage folder on your hard drive as

 explainedin5.2.2.1General(DataDirectory).Onlytheavailablespace

on your hard drive limits the number of snapshots that can be taken.

Message Display Box—Displaysallsystemmessages;forexample,

that a certain camera is disconnected.

Close Window (11) — Click to discontinue Viewer operation.

Minimize Window (12) — Click to minimize the Viewer window.

5.2 Conguration

Before you can effectively use the Viewer program and all its features,

allcamerasconnectedtothenetworkneedtobecongured(as

mentionedbrieyinthe3.2Viewerintroduction).ClicktheCongure

buttonontheViewercontrolscreentodisplaythe“CongureCameras”/

“General Options” menu,

andselect“Congure

Cameras.” NOTE: If you’re

prompted by a Windows

security alert asking you if

you want to block the

“IPCamViewer” program,

click “Unblock”; otherwise,

the Viewer program will not

be able to function properly.

18

VIEWER OPERATION

5.2.1 Congure Cameras

Clicking“CongureCameras”onthepopupmenuwilldisplaythefour

submenus and each of their various options, as detailed below.

5.2.1.1 Camera

Channel — Select the channel number you want to set.

Camera Search — All cameras found on your local network will be

displayed in this window.

Select — With a camera highlighted in the Camera Search window,

 click“Select”tollintheCameraCongurationtexteldsinthepanel

above with that camera’s parameters.

Refresh — Ifthecamerayouexpectedtoseedoesn’tappearinthe

 CameraSearchwindow(includinganycamera[s]connectedtoyour

 networksincethelastscan),clicktorescanandre-display.

Name* — Enter an easily recognizable name for the selected camera

so you can quickly identify its location and purpose. The default entry

 istherstsixbytesofthecamera’sMACaddress.

Model — Thisidentiestheselectedcamera(andcan’tbechanged).

IP* — Enter the IP address of the selected camera.

OK

Cancel

Password

19

VIEWER OPERATION

Username — Enter the username of the selected camera.

Web Port* — Enter the Web port of the camera. The default is 80.

Password — Enter the password for the camera. The default is 1234.

Video Format — If the camera supports this function, set it for either

 MJPEGorMPEG4.

Reset — ClicktocleartheeldsintheCameraCongurationpanel.

OK — Click to save the current

settings. If all entries and

changes are made correclty,

the selected camera’s view

will display on the Viewer

 screen(asshownatright).

Cancel — Click to cancel any

changes you’ve made before

saving.

* It’s recommended that you

 click“Select”tollthiseld.

5.2.1.2 Schedule Recording

Channel — S

OK

Cancel

20

VIEWER OPERATION

Channel — Select the channel number you want to set.

One Time Schedules — This window displays recording schedules you

 setforspeciccamerasthatwillbeexecutedonlyonce.

New / One Time Schedules —

Click to display a new One

Time Schedule screen for the

selected camera. Enter/select

“To” and “From” dates/times,

then click “OK” to save the

settings or “Cancel” to undo

any changes. NOTE: Make

sure all your entries are for

future times/dates; otherwise,

 allthesettingsareinvalidandtheViewerwon’trecordasexpected.

Weekly Schedules — This window displays recording schedules you

 setforspeciccamerasthatwillrunrepeatedlyontheday(s)selected.

New / Weekly

Schedules — Click

to display a new

Weekly Schedule

screen for the

selected camera.

Select applicable

days of the week;

enter/select a

“From” time; then

 setthedurationofthevideorecordinginthe“Period”eld(HH:MM:SS

 format).Theendtimeoftherecordingwillbecalculatedautomatically

 anddisplayedinthe“To”eld.Alternatively,click“AllTimeRecord”

 torecordthefull24-hourperiod(12:00:00AMto11:59:59PM)ofevery

day. Click “OK” to save the settings; click “Cancel” to undo any changes.

Edit — For either schedule option, highlight a listing in the window and

click “Edit” to modify the settings.

Delete — For either schedule option, highlight a listing in the window

and click “Delete” to remove it.

OK — Click to save the current settings.

Cancel — Click to cancel any changes you’ve made on the Schedule

Recording screen before saving.

Page is loading ...

Intellinet 550918, NSC10-WG 550918, NSC10-WG Network Camera User manual

Related papers

Other documents