Unisen 265 User manual

IMMERSIVE SOUND LED LCD HDTV

with Integrated Sound Projector

MODELS

154 Series

164 Series

265 Series

OWNER’S GUIDE

For questions:•

Visit our website at www.mitsubishi-tv.com. -

E-mail us at MDEAservice@mdea.com. -

Call Consumer Relations at - 800-332-2119 for operational or connection assistance.

For information on • System Reset, please see the back cover.

To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call •

800-553-7278.

265 Series.• IR emitter cables for NetCommand home-theater control are available for purchase from

Mitsubishi.

Call 800-553-7278 and

request either part number 242D483020 (two-ended cable) or part

number 299P254020 (four-ended cable).

®

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

FCC Declaration of Conformity

Product: LCD Flat Panel HDTV

Models: LT-55154

LT-40164, LT-46164, LT-55164

LT-46265, LT-55265

Responsible

Party:

Mitsubishi Digital Electronics

America, Inc.

9351 Jeronimo Road

Irvine, CA 92618-1904

Telephone: (800) 332-2119

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1)

This device may not cause harmful interference,

and

(2) This device must accept any interference

received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential instal-

lation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may

cause harmful interference to radio communica-

tions. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment

and the receiver.

- Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV

technician for help.

Changes or modifications not expressly

approved by Mitsubishi could cause harmful

interference and would void the user’s authority

to operate this equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or moisture.

This apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases, shall be placed on the apparatus.

WARNING: This product contains chemicals known

to the State of California to cause cancer and/or birth

defects or other reproductive harm.

TV WEIGHT: This TV is heavy. Exercise extreme care

when lifting or moving it. Lift or move the TV with a

minimum of two adults. To prevent damage to the TV,

avoid jarring or moving it while it is turned on. Always

power off your TV, unplug the power cord, and discon-

nect all cables before moving it.

Note: Features and specifications described in this

owner’s guide are subject to change without notice.

WARNING: T

his product shall be connected to a MAINS

socket outlet with a protective earthing connection.

MAINS DISCONNECTION: The mains plug is used

as the disconnect device. The mains plug shall remain

readily operable.

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user of the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to consti-

tute a risk of electric shock to persons.

The exclamation point within an equilat-

eral triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

Downloaded From TV-Manual.com Manuals

For assistance call 1(800) 332-2119

Contents

Important Information About Your TV

Installation and Operating Notes ............. 4

Important Safety Instructions ................ 5

Stand Installation ......................... 6

Wall-Mounting ........................... 7

1 Basic Setup and Operation

Package Contents ....................... 9

Before You Begin ....................... 10

First-Time Power-On ..................... 10

TV Controls ........................... 11

Remote Control ..................... 11

The TOOLS Key and Menu ............. 12

TV Control Panel .................... 13

POWER Indicator .................... 13

Setting Up TV Inputs..................... 14

Basic TV Operation...................... 16

Using the TV with a Personal Computer ....... 19

2 TV Connections

Before You Begin ....................... 21

Connection Types and Audio/Video Quality .... 21

Inputs and Outputs ...................... 22

Cable Routing ......................... 22

H

DMI Device .............................24

Y Pb Pr Component Video Device ........... 25

DVI Video Device ....................... 25

Antenna or Cable TV Service ............... 26

Composite Video Device .................. 26

VCR or DVD Recorder to an Antenna or

Wall Outlet Cable ...................... 26

A/V Receiver .......................... 27

A/V Receiver with HDMI Output ............. 27

Supplemental Audio Connections ......... 28

3 TV Features

Sleep Timer ........................... 29

FAV (Favorite Channels) ................... 29

ChannelView Channel Listings .............. 30

Status Display ......................... 31

Using an External Sound System ............ 32

Picture Shape and Display Formats .......... 33

Camera Images and Music Files ............ 34

USB Source Devices .................. 34

Photos and Motion Video as

Composite Video ................... 36

Using an Audio-Only Device ............ 36

Wireless Audio Playback ............... 37

Sound Projector ........................ 38

StreamTV™ Internet Media ................ 42

Introduction to Home-Theater Control ........ 45

4 TV Menus

Main Menu ............................ 46

Picture............................... 46

Sound ............................... 49

Captions ............................. 51

Setup ............................... 52

Inputs ............................... 55

Lock ................................ 57

5 NetCommand IR Control

About NetCommand IR Control ............. 60

IR Emitters ............................ 61

NetCommand Setup ..................... 62

Operating NetCommand-Controlled Devices ... 63

6 NetCommand IR Control of an A/V Receiver

Controlling an A/V Receiver after NetCommand

Setup .............................. 67

Setting Up A/V Receiver Control

Power and Volume ................... 68

Automatic Audio/Video Switching Over

an HDMI Connection ................. 69

Appendices

Appendix A: Programming the Remote Control . 73

Appendix B: Bypassing the Parental Lock ..... 79

Appendix C: HDMI Control of CEC Devices .... 81

Appendix D: TV Care .................... 84

Appendix E: Troubleshooting .............. 85

Trademark and License Information .......... 92

Warranty .............................. 99

Network Service Disclaimer ............... 100

Index ................................ 101

Downloaded From TV-Manual.com Manuals

4

For assistance call 1(800) 332-2119

Important Information About Your TV

Installation and Operating Notes

Custom cabinet installation must allow for proper

air circulation around the television.

NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER

IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S

ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PRO-

VIDES GUIDELINES FOR THE PROPER GROUNDING AND,

IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND

SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF

THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY

AS PRACTICAL.

TV Software

Do not attempt to update the software of this TV with

software or USB drives not provided by or authorized

by Mitsubishi Digital Electronics America, Inc. Non-

authorized software may damage the TV and will not be

covered by the warranty.

For Your Records

Record the model number, serial number, and

purchase date of your TV. The model and serial

numbers are on the back of the TV. Refer to this

page when requesting assistance with the TV.

MODEL NUMBER

SERIAL NUMBER

PURCHASE DATE

RETAILER NAME

LOCATION

Children and TV Viewing

The American Academy of Pediatrics discourages

television viewing for children younger than two years of

age.

If Your TV Gets Damaged

Crystalline liquid may leak from the LCD panel and

broken glass may be scattered.

CAUTION: The crystalline liquid is toxic. Avoid

contact with your skin, eyes, or mouth. DO NOT

touch the broken glass or crystalline liquid. DO NOT

get glass fragments or crystalline liquid into eyes or

mouth. Should either contact your eyes or mouth,

rinse the contacted area thoroughly with water and

consult your doctor.

Disposal of Your TV

The LCD panel contains a small amount of crystalline

liquid which is toxic and should not be touched.

DO NOT dispose of the TV with general household

waste. For disposal or recycling information, contact

your local authorities or the Electronic Industries Alli-

ance at www.eiae.org.

Downloaded From TV-Manual.com Manuals

5

For assistance call 1(800) 332-2119

Important Safety Instructions

Please read the following safeguards for your TV and

retain for future reference. Always follow all warnings

and instructions marked on the television.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart,

stand, tripod, bracket,

or table specified

by the manufacturer,

or sold with the

apparatus. When

a cart is used, use

caution when moving

the cart/apparatus

combination to avoid

injury from tip-over.

13) Unplug this apparatus

during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

ANT E NNA

LE AD IN W IR E

ANT E NNA

DIS C HAR G E UNIT

(NE C AR T IC L E 810-20)

G R OUNDING

C ONDUC T OR S

(NE C AR T IC L E 810-21)

G R OUND C LAMP S

P OW E R S E R V IC E G R OU NDING

E LE C T R ODE S Y S T E M

(NE C AR T 250, P AR T H )

G R OUND C LAMP

E LE C T R IC

S E R VIC E

E QUIP ME NT

NE C — NAT IO NAL E LE C TR IC AL C O DE

E XAMP LE O F ANT E NNA G R OUNDING

Outdoor Antenna Grounding

If an outside antenna or cable system is connected

to the TV, be sure the antenna or cable system is

grounded so as to provide some protection against

voltage surges and built-up static charges.

Replacement Parts

When replacement parts are required, be sure the

service technician has used replacement parts speci-

fied by the manufacturer or have the same character-

istics as the original part. Unauthorized substitutions

may result in fire, electric shock or other hazards.

Downloaded From TV-Manual.com Manuals

6

For assistance call 1(800) 332-2119

1

Back

Extension pieces

on back of stand

2

3

TV

CAUTION.

Place the

stand in the foam insert

with the extension pieces

facing away from the TV.

Otherwise, the TV will be

damaged in transit.

Protect the TV and

stand with the original

packing material.

DON’T place your hand where it can get

caught between the TV and stand.

DO support the TV

under the corners.

TV in protective

wrapping

Extension pieces on stand

must face out, away from TV.

Repacking the Stand

Two adults are required to lift the TV.

Stand Installation

CAUTION

Using this TV with other than the authorized accessories may cause the TV to become unstable, which •

can cause damage to the product or possible injury.

At least TWO PEOPLE are required to install the stand. Support the TV near the corners as shown. Failure to follow •

these recommendations may result in personal injury and damage to the product.

Required: Phillips Screwdriver

1

Extension pieces

on back of stand

2

3

TV

CAUTION.

Place the

stand in the foam insert

with the extension pieces

facing away from the TV.

Otherwise, the TV will be

damaged in transit.

Protect the TV and

stand with the original

packing material.

DON’T place your hand where it can

get caught under the TV.

DO support the TV

under the corners.

TV in protective

wrapping

Extension pieces on stand

must face out, away from TV.

Repacking the Stand

Two adults are required to lift the TV.

BACK

Note

40- or 46-inch TV:• If planning to wall-mount the TV, there is no need to install the stand.

55-inch TV: • The TV comes from the factory with the stand pre-installed.

Downloaded From TV-Manual.com Manuals

7

For assistance call 1(800) 332-2119

Wall-Mounting

To order a wall-mount kit, please contact Peer-

less Industries, Inc. at (800) 473-3753 or visit

www.peerlessmounts.com. Order wall-mount kit model

ST650.

To order a wall-mount kit from Mitsubishi Digital Elec-

tronics America, Inc., please visit www.mitsuparts.com

or call (800) 553-7278.

Complete installation instructions are included with the kit.

Stand Removal Prior to Wall-Mounting

Disconnect the TV’s AC power cord from the AC

1.

power outlet.

Spread the protective sheet that was wrapped

2.

around the TV on a flat, even surface, such as a

sturdy table. The protective sheet will help prevent

damage to the display.

IMPORTANT: To avoid damaging the screen,

make sure there are no foreign objects under or

on top of the protective sheet.

Position one person on each side of the TV (left and

3.

right sides). Have each person firmly grasp their side

of the TV and gently place it face down on the pro-

tective sheet with the display stand hanging over the

edge of the table. See the illustration to the right.

Use a magnetic philips screwdriver to remove the

4.

stand screws from the recessed holes (see illustra-

tion to right). Note: A regular screwdriver can be

used with a separate magnetic pick-up tool.

While one person holds the TV with both hands,

5.

have the other person grasp the stand (see illustra-

tion to the right) and remove the stand by pulling it

away from the TV in the direction of the large arrow

shown in both illustrations.

5BCMF

1SPUFDUJWF

TIFFU

57

4UBOE

CAUTION

At least TWO PEOPLE are needed to safely remove the stand. Have one person hold the TV while the other person

removes the stand. Failure to follow these recommendations may result in personal injury and damage to the product.

Note

55-inch TV: • Remove the factory-installed stand prior to wall-mounting.

40- or 46-inch TV:• If you installed the stand for table-top use, follow these instructions to remove it prior

to wall-mounting the TV.

55-inch TVs

(6 screws)

40- and 46-inch TVs

(4 screws)

Protective

Sheet

Pull stand

to remove.

Downloaded From TV-Manual.com Manuals

8

For assistance call 1(800) 332-2119

Special Features of Your TV

Your new high-definition widescreen television has

many special features that make it the perfect center of

your home entertainment system, including:

1080p High-Definition LCD Display System

Your Mitsubishi LED LCD HDTV uses a full 1920 x 1080

LCD panel to create the picture you see on the screen. All

images are displayed at 1080p. The TV uses new Plush

1080p

®

5G digital video processing to convert lower-reso-

lution signals to 1080p for display.

True120Hz and True240Hz

True120Hz (154 and 164 series) and True240Hz (265 series)

make fast-moving images appear smoother and more fluid,

free from motion blur. It does this by doubling the tradi-

tional progressive scan frame rate and creates new frames

of video between the traditional frames to create smoother

moving images. True120Hz/True240Hz also smooth film

judder (image vibration) that may be present in film-based

content such as movies.

16:9 Widescreen Picture Format

Enjoy a full theatrical experience in the comfort of your

home. View pictures as film directors intended them.

Digital TV broadcasts, DVDs and newer video game

consoles support this widescreen format.

Integrated HDTV Tuner

Your widescreen Mitsubishi HDTV has an internal HDTV

tuner able to receive both over-the-air HDTV broad-

casts (received via an antenna) and non-scrambled

digital cable broadcasts, including non-scrambled

HDTV cable programming.

High-Definition Video Inputs

Component Video Inputs.• Also called Y/Pb/Pr

inputs, these inputs receive standard analog video

formats of 480i, 480p, 720p, and 1080i high-defini-

tion signals. This provides a high level of flexibility

when connecting DVD players/recorders, cable

boxes, and satellite receivers.

HDMI Inputs.• These inputs accept digital 480i,

480p, 720p, 1080i, and 1080p video signals plus

bitstream and PCM digital stereo signals. The

HDMI™ inputs can also accept a variety of PC

signals and resolutions.

Used with an adapter, these inputs also accept

compatible digital DVI video signals. HDMI

inputs provide additional high-performance,

high-definition connections for maximum flexibility

in your choice of home theater products. The HDMI

inputs are HDCP copy-protection compatible.

Easy Connect Auto Input Sensing

Easy Connect™ Auto Input Sensing automatically rec-

ognizes when you plug in a device and prompts you to

assign a name to it.

Home-Theater Control

HDMI Control

Available on all models. HDMI devices with Consumer

Electronics Control (CEC) capabilities may be compatible

with the TV’s HDMI Control feature. Compatible devices

can receive control signals through the HDMI connection,

allowing the TV’s remote control to operate some func-

tions of these devices.

NetCommand with IR Learning

265 Series. NetCommand

®

supports IR (infrared) control

of products such as VCRs, DVD players, cable boxes,

and satellite receivers. NetCommand can “learn” remote

control signals directly from many devices, allowing you

to create a customized NetCommand-controlled home-

theater system.

Sound Projector

Sound Projector technology uses the TV’s bank of

speakers to create a simulated surround sound effect

by reflecting sound off the room walls.

StreamTV™ Internet

StreamTV brings many popular internet applications to your

TV. Among them is the VUDU

™

movie service, offering the

largest on-demand HD movie selection anywhere, featur-

ing full 1080p and 5.1 surround sound. VUDU allows you

to enjoy movies with no store visits, no mailing, no late fees

and no subscriptions.

ENERGY STAR

®

This is an ENERGY STAR

®

qualified TV. Products that

earn the ENERGY STAR prevent greenhouse gas emis-

sions by meeting strict energy efficiency guidelines set

by the U.S. Environmental Protection Agency and the

U.S. Department of Energy.

This TV uses power within ENERGY STAR guidelines

except when Picture Mode is set to Brilliant.

Downloaded From TV-Manual.com Manuals

9

For assistance call 1(800) 332-2119

Basic Setup and Operation

1

Installing the Remote Control

Batteries

Remove the remote control’s back cover by

1.

gently pressing in the tab and lifting off the cover.

Load the batteries, making sure the polarities

2.

(+) and (-) are correct. For best results, insert

the negative (-) end first.

Snap the cover back in place.

3.

2

1

The remote

control requires

two AA alkaline

batteries.

Remote Control

Two AA Batteries

AA

Basic Owner’s Guide

Quick Setup Guide

Product Registration

Card

Power Cord

Cable Ties

Stand Screws (40- and

46-inch TVs only)

265 Series. Calibration

Microphone

Package Contents

Please take a moment to review the following list of

items to ensure that you have received everything.

Downloaded From TV-Manual.com Manuals

10 1. Basic Setup and Operation

For assistance call 1(800) 332-2119

TV Tips

Turning the TV On or Off

Point the emitter (bulb) end of the remote •

control at the front of the TV and press the

POWER

button.

Press the •

POWER

button on the TV control

panel.

Controlling Sound Volume

Press •

VOL

to adjust the sound level.

See also • “Controlling A/V Receiver Sound

Volume” on page 32.

Before You Begin

Review the important safety, installation, and oper-

1.

ating information at the beginning of this book.

Choose a location for your TV.

2.

• See the stand-installation or wall-mounting

requirements starting on page 6.

• Allowatleastfourinchesofspaceonallsides

of the TV to help prevent overheating. Over-

heating may cause premature failure of the TV.

• Avoidlocationswherelightmayreflectoffthe

screen.

Install the batteries in the remote control.

3.

Plug the TV into an AC power outlet.

4.

TV power connection

Press the

1.

TV

key to

ensure that the remote

control is in

TV

mode.

TV

Aim the emitter end of the

2.

remote control at the TV

and press the

POWER

key

.

Wait for the Welcome

screen.

If you wish to change the

3.

menu language to Español,

press .

Press

4.

to move to the

energy-mode selections.

Select Home.

Press

5.

to highlight EXIT.

Press

ENTER

to clear the

menu.

Welcome Screen Energy Options

Mitsubishi recommends the • Home setting,

which uses power within ENERGY STAR

®

guidelines.

The • Retail setting looks best under bright

lighting. In this mode, the TV uses power in

excess of ENERGY STAR guidelines.

This table compares energy choices offered in the

Welcome screen.

Home Retail

Picture Mode Bright Brilliant

Backlight Level

Reduced

Brightness

Full Brightness

First-Time Power-On

Downloaded From TV-Manual.com Manuals

1. Basic Setup and Operation 11

For assistance call 1(800) 332-2119

TV Controls

Remote Control

For more on use and care of the remote control, see

page 84.

Emitter (Bulb) End

Note: To operate other audio/video devices using the

TV’s remote control, use any of these methods:

• SeeAppendix A, “Programming the Remote

Control.”

• ForHDMIdevicescompatiblewiththeTV’sHDMI

Control feature, see Appendix C.

• 265 Series

See - page 60 for NetCommand IR “Learning” of

device keys.

For use of specific keys with NetCommand- -

controlled devices, see “Special Operation

Methods,” page 64.

(

PAUSE

)

Freezes a broadcast TV picture.

Record/Playback controls for external devices

When remote control is programmed, page 73

HDMI control, page 83

265 Series: With NetCommand, page 66

Powers TV on or off.

Number/letter keys

Channel tuning, page 16

Pass-code entry, page 57,

page 43

Sleep Timer, page 29

TV CAB/SAT DVD AUDIO VCR

P

ress the key for the device type to

control. Leave in TV mode for normal

TV viewing.

GUIDE

ChannelView listings, page 30

.

INFO

TV status

or TV help.

MUTE

Mutes the TV speakers.

TOOLS

Displays shortcuts for the number keys.

Press to check if shortcuts are available

for the current device. See the next

page.

VOL

Controls volume of TV speakers.

CH

PAGE

Changes channels; moves to another

page in a menu or list.

Adds a separator in digital channel

numbers. Clears some menu entries.

AUDIO

Audio settings, page 49

VIDEO

Video settings, page 46

MENU

Displays or clears the TV main

menu (page 46).

Also steps

back one menu.

EXIT

Clears all menus.

LAST

Returns to the previous channel;

moves back one menu

F1–F4.

265 Series. Special keys for

use with NetCommand IR control. See

“Initial NetCommand Setup”.

ENTER

Selects a channel number or menu item.

Navigation and adjustment

controls

FAV

Displays up to nine favorite

sources, page 29.

FORMAT

Changes picture shape,

page 18

INTERNET

Connects to StreamTV internet

content, page 42.

INPUT

Press to select a TV input,

page 16.

Downloaded From TV-Manual.com Manuals

12 1. Basic Setup and Operation

For assistance call 1(800) 332-2119

TV Controls, continued

PICTURE SOUND

TV

Picture Shortcuts

1 Picture Mode Brilliant page 46

4 Picture Mode Natural

164 and 265 Series. Brilliant and

Natural Picture Modes are the

default choices. If your installer has

set up special Picture Modes in the

Picture > Advanced menu, select

them from this menu.

page 48

7 Backlight turns off the backlight.

Press any number key to turn the

backlight back on.

---

Device-Specific Shortcuts

Availability varies, depending on equip-

ment features and setup.

3 CC. Turns closed

captions on/off

page 51

Sound Shortcuts

2 Subwoofer. Turns on or off audio to a con-

nected subwoofer.

page 50

5 Surround. Selects Sound Mode Surround page 50

8 Night. Selects Sound Mode Night

Sample Tools menu

Tools

The TOOLS Key and Menu

Press the

TOOLS

key to check for shortcuts. The Tools menu lists shortcut keys

for common functions. Press the number key to activate the shortcut. See the

sample menu below.

Shortcuts specific to the current device are in the third column.•

Shortcuts may be available for a CEC-enabled device. See • Appendix C,

“HDMI Control of CEC Devices,” page 81.

265 Series.• After setting up NetCommand control for a device, check the

Tools menu for shortcuts. See page 62.

TOOLS

Downloaded From TV-Manual.com Manuals

1. Basic Setup and Operation 13

For assistance call 1(800) 332-2119

TV Control Panel

Buttons on the control panel duplicate some keys on

the remote control.

To display the main menu, press •

INPUT

and

VOL

+

simultaneously for about 10 seconds. Press and

hold

INPUT

and

VOL

+

for 10 seconds to clear the

menu.

Refer to • left labels when no TV menus are dis-

played.

Refer to • right labels when using TV menus or after

activating a special function.

System Reset

If the TV fails to respond to the remote control, the

control-panel buttons, or will not power on/off, perform

System Reset. Recent setting changes made before

using System Reset may be lost.

To perform System Reset, press and hold the

POWER

button on the control panel for 10 seconds.

Panel-Lock Release

To • release the Panel Lock using the TV control

panel, press and hold the

INPUT

button on the

control panel for ten seconds. If the TV is off, press

the

POWER

button to make it power on.

To activate the Panel Lock, use the • Lock menu,

page 59.

TV control panel

TV Controls, continued

POWER

INPUT

ENTER

CH

VOL

POWER Indicator

POWER

Key

Off

Steady On

Slow Blinking

Fast Blinking

LED Color TV Condition

None

TV is powered off. Normal operation.

Green

TV is powered on. Normal operation.

Green

TV powered off, auto-on TV Timer is set.

Normal operation. TV can be turned on at any time.

Red/

Yellow

TV may require service.

Hold power button on front panel for 10 seconds to reset TV.•

If LED continues to flash red and yellow after reset, turn off the •

TV and unplug it from the AC power source. Wait one minute

and then plug the set back in.

If LED continues to flash red and yellow,•

go to

www.mitsubishi-tv.com or call 1-800-332-2119 to receive Autho-

rized Service Center information.

You may be asked to count how many times the LED flashes

each color to assist in troubleshooting.

Downloaded From TV-Manual.com Manuals

14 1. Basic Setup and Operation

For assistance call 1(800) 332-2119

Setting Up Inputs with Auto Input Sensing

Power on the TV.

1.

Power on the devices to ensure detection.

2.

Connect one device to the TV, making note of the

3.

TV input jack.

The TV will display the New Device Found screen if

the connection type is detectable.

Highlight the device type in the on-screen list and

4.

press

ENTER

. The name you select here will appear

in the Input Selection menu.

Sample New Device

Found screen.

Important Note for NetCommand Users

265 Series. Be sure to select the correct device

type here. Although you can change the device type

later using the Inputs > Name menu, any “learned”

NetCommand IR codes will be erased when you

make the change.

Press

5.

EXIT

to close the New Device Found screen.

Repeat the preceding steps for each for each addi-

6.

tional device you want to add.

Using the ANT (Antenna) Input

If using an antenna or direct cable service (no cable

box), connect the incoming coaxial cable to the TV’s

ANT

input. Refer to page 26.

You must perform a channel scan to enable recep-

tion of digital channels. If you skip this step, the TV

will receive only analog channels. The channel scan

will search for high-definition and standard-definition

channels available in your area.

Memorizing Channels with Channel Scan

For the ANT input

To start channel memorization

Power on the TV.

1.

Press

2.

MENU

and open the Setup > Channel menu.

Start channel memorization from the Setup > Channel

menu.

Press

3.

to enter the menu.

Highlight

4.

Ant Air if connected to an

over-the-air antenna. Highlight Ant

Cable for service over direct cable

(no cable box). Press

ENTER

to add a

check.

Select the scan type.

5.

For first-time setup, highlight • All

channels.

To scan for channels not already •

in memory, highlight New only.

Press

ENTER

to add a check.

Highlight

6.

Scan and press

ENTER

.

Channel memorization may take up

to 15 minutes to complete.

To stop channel memorization before completion,

press

CANCEL

.

At any time after Channel Scan,

Use the • Setup > Channel > Edit menu (page 53) to

add or delete individual channels from memory.

Perform an additive scan with the • New only option

to add channels not already in memory.

Repeat the • All channels scan if you move the TV

to a new geographic area with a different channel

line-up or reposition the antenna.

Setting Up TV Inputs

Downloaded From TV-Manual.com Manuals

1. Basic Setup and Operation 15

For assistance call 1(800) 332-2119

About Auto Input Sensing

This TV’s Easy Connect™ Auto Input Sensing feature

detects the following connections automatically:

Analog video jacks from inputs 1, 2, and 3•

HDMI inputs (when powered on)•

• USB device containing photo and music files

(JPG and MP3 formats).

Auto Input Sensing for Most Devices

When you first connect a device, the TV will:

a. Detect the connected device and automati-

cally switch to it.

b. Prompt you to identify the device type.

c. Repeat these steps for other newly detected

devices.

When You First Connect a Device

Most Device Types.• Select the device type from

the on-screen list. The device type you select here

will appear as an icon in the Input Selection menu.

A/V Receiver. •

For an HDMI-equipped A/V

receiver, select AVR

from the list of device types if

the A/V receiver is not recognized automatically.

HDMI CEC Devices Compatible with the •

TV’s HDMI Control Feature.

Compatible

CEC-enabled HDMI-equipped devices are often

recognized automatically by the TV.

HDMI Control

may allow you to control some functions of a CEC-

enabled device. See Appendix C, “HDMI Control

of CEC Devices.”

New Device Found screen for a device with HDMI

control enabled. Select On if you want to enable the

TV’s HDMI control of the device. In some cases, as

in the example above, you will also be prompted to

select a device name.

Tips on Auto Sensing

Choose a different name for each input.•

The antenna input (•

ANT

) is never detected,

although you can turn off the unused antenna

input in the Inputs > Name menu.

Change the device type displayed in the • Input

Selection menu by using the Inputs > Name

menu (page 55).

Some HDMI devices can automatically tell the TV •

what name to use in the Input Selection menu

and you will be unable to change the name.

The TV is unable to detect a new connection if •

the current input is USB, Bluetooth

®

, or internet.

Switch to a different input before connecting.

265 series.• Any “learned” NetCommand IR

codes will be erased if you change the device

type in the Inputs > Name menu.

Reactivating Auto Input Sensing

for an HDMI Input

After you disconnect an HDMI device, Auto Input

Sensing is temporarily disabled. Perform these

steps:

Disconnect the HDMI device.

1.

Delete the removed HDMI device in the

2.

Inputs >

Name menu (see “Removing an HDMI Device,”

page 83).

Connect the new device and the

3.

New Device

Found screen will display.

Setting Up TV Inputs, continued

Downloaded From TV-Manual.com Manuals

16 1. Basic Setup and Operation

For assistance call 1(800) 332-2119

Selecting an Input to Watch

Press

1.

INPUT

.

Press

2.

and to highlight an input icon.

Sample Input selection menu, DVD input selected

Press

3.

ENTER

to switch to the input.

To control the input device, use the device’s remote

4.

control or see “Introduction to Home-Theater

Control,” page 45.

Note: In most cases, to see a named icon for a con-

nected device (as in the samples), you must ﬁrst

assign a name either

• Whenthedeviceisfirstconnectedandthe

New Device Found menu offers a choice

of names.

• ByusingtheInputs > Name menu to

assign or change a name at any time after

the TV has detected the connection.

More About the Input Selection Menu

• Toassignhelpfulnamestotheicons,seethe

Inputs > Name menu, page 55.

• ToremoveunwantedAntenna,Bluetooth

®

, or HDMI

device icons from the Input Selection menu, see

the Inputs > Name menu, page 55.

• Torearrangetheicons,seetheInputs > Order

menu, page 56.

Basic TV Operation

Watching Broadcast TV

TV Connected to an Antenna or Direct Cable

Service (no cable box)

Note: Perform channel memorization to enable recep-

tion of digital channels. See page 14.

Press

1.

INPUT

to display the Input Selection menu.

Highlight the antenna or cable icon and press

2.

ENTER

.

Sample Input Selection menu, antenna input selected

To tune to a

3.

channel from the

ANT

input, use any of

these methods.

Enter the channel number using the number •

keys on the remote control and press

ENTER

.

For a two-part digital channel, such as 3-1,

press

3

—

CANCEL

1 ENTER

.

Press •

CH

to change channels one channel at a

time.

Press and hold •

CH

to speed through channels.

Press •

LAST

to return to the previous channel.

Use the Fav (Favorites) feature to tune to up to •

nine favorite channels. See page 29.

Press •

GUIDE

to display ChannelView channel

listings, highlight a channel number, and press

ENTER

to tune.

Set up ChannelView custom channel banks •

and use the

CH

/ key to tune to predefined

groups of channels. See page 30.

Downloaded From TV-Manual.com Manuals

1. Basic Setup and Operation 17

For assistance call 1(800) 332-2119

Picture Settings

To get the best picture under different viewing con-

1.

ditions, set the Picture Mode first before changing

other video settings. See page 46.

a. Press

VIDEO.

b. Press until Picture Mode

displays.

c. Press to make one of these selections:

Name When to Use

Brilliant

Under bright light

Game

With gaming consoles (inputs

named

Game

or

PC

only)

Bright For most daytime viewing

Natural For most nighttime viewing

Press

2.

to display the name of another adjust-

ment.

Press

3.

to make the adjustment.

Press

4.

EXIT

to clear the display.

Additional picture options are available through these

menus:

Menu Name Page

Picture > Video 46

Picture > Picture Plus

47

Picture > Perfect

(265 Series)

48

Picture > Advanced (164 and 265 Series) 48

Basic Audio Controls

Controlling Sound Volume

Press •

VOL

to adjust the sound level

of the TV speakers.

Control •

subwoofer volume with an

on-screen slider

. See page 49. Set

Sound > Global > Subwoofer to

On to make this adjustment avail-

able.

See also • “Controlling A/V Receiver

Sound Volume” on page 32.

Changing Audio Settings (TV Speakers Only)

Press

1.

AUDIO

.

Press

2.

to find the adjust-

ment you want. See page 49.

Press

3.

to change.

Changing the Audio Output

To switch from the internal TV speakers to an external

sound system,

Press

1.

AUDIO

.

Press

2.

to display the TV Speakers option.

Press

3.

to change to Off.

Basic TV Operation, continued

TV Care

See page 84.

Assistance

For troubleshooting, service, and product support, •

see Appendix E, starting on page 85.

For warranty information, see • page 99.

Downloaded From TV-Manual.com Manuals

18 1. Basic Setup and Operation

For assistance call 1(800) 332-2119

More TV Features

Feature

Page

Parental controls (Lock menu) 57

Audio Lock (controls your sound system with

the TV’s remote control left in

TV

mode.)

74

TV Clock. Set the TV Clock if you plan to use

the TV Timer (page 52) or ChannelView (page

30).

52

Favorite channels or sources 29

ChannelView and custom channel collections 30

Changing the input names that appear in the

Input Selection menu (Inputs > Name menu)

55

Digital camera images and mp3 music files 34

164 and 265 Series. Listening to a wireless

audio device with the TV speakers

37

StreamTV™ internet access 42

Basic TV Operation, continued

The FORMAT Key and Picture Shape

Important

Black bars at the edges of

the screen are common in HD

pictures. Black bars are not a

defect of the TV.

Black bars are added by broad-•

casters to fill the 16:9 screen

area while preserving the original

aspect ratio of the picture.

Your cable box, satellite receiver, •

or other device may also be

altering the broadcast picture.

If your device offers output in

native format, try using it with

Mitsubishi picture formats.

Sample Uses of the

FORMAT

Key

You can use the

FORMAT

key to reduce or eliminate black areas at the

edges of the picture.

Press

Squarish 4:3 image is

narrower than the 16:9

screen; unused areas at the

sides are filled with black.

Wide Expand mode stretches

the picture sideways to fill the

screen.

Press

Wide 2.35:1 anamorphic DVD

image; unused areas at the

top and bottom are filled with

black (letterbox effect).

Zoom mode. The picture fills

the screen. All four edges are

cropped in this mode.

Repeatedly press the

FORMAT

key to cycle

through displays for the

current program. The

TV will remember the

format you last used on

each input.

For details, see page 33

Feature

Page

Programming the remote control to operate

other A/V devices

73

Controlling compatible devices using HDMI

CEC control

81

265 Series. Controlling A/V devices with Net-

Command

60

Downloaded From TV-Manual.com Manuals

1. Basic Setup and Operation 19

For assistance call 1(800) 332-2119

Connecting a Computer to the TV

Use one of the connection methods listed below based

on your computer’s video output.

Computer

Video Output

Video Connection

Audio

Connection

Digital DVI DVI-to-HDMI cable

or an HDMI cable

with a DVI-to-HDMI

adapter

Analog audio

cable with mini

plugs

HDMI HDMI-to-HDMI

cable

No additional

audio connec-

tion is required.

IMPORTANT

This TV accepts digital computer

video signals only. This TV is not

compatible with VGA (analog)

computer video.

VGA

PC MONITOR OUT

Connect the computer’s digital signal output to one

1.

of the TV’s HDMI jacks. See the connection dia-

grams for the method suited to your equipment.

Connect the computer’s audio output using one of

2.

these options:

• FordigitalDVIvideosignals,connectthe

analog audio output to the TV’s

DVI/PC AUDIO

INPUT

jack.

• ForHDMIsignals,noadditionalaudioconnec-

tion is required.

Note: If you are unable to hear audio from the

computer, there may be an incompatibility in

the computer’s hardware, software, or internal

settings. Consult a trained computer technician

for advice.

Power on the TV and computer. The TV will detect

3.

the connection and display the New Device Found

screen.

In the

4.

New Device Found screen, press to

highlight PC in the list of device types. It is impor-

tant to use the name PC so that the TV processes

the PC signal correctly.

Highlight

5.

EXIT and press

ENTER

to close the New

Device Found screen.

Note:

If your computer provides digital audio output

(coaxial or optical), you can connect it directly

to a digital A/V receiver and bypass the TV.

Using the TV with a Personal Computer

H

DMI Connection

Mitsubishi recommends using high-speed HDMI

cables to connect newer devices incorporating HDMI

technology.

Computer with

HDMI output

HDMI-to-HDMI

cable

TV

An HDMI-to-HDMI connection carries all video and

audio on a single cable.

HDMI and Digital Surround Sound

The TV’s HDMI inputs can receive digital surround

sound from an HDMI device. Use an HDMI connec-

tion if you want to hear digital surround sound from

the TV’s internal speaker array.

DVI Video Connection

DVI OUT

AUDIO

OUT

Computer

with Digital

DVI output

DVI-to-HDMI

cable

Audio cable

TV

A DVI connection from a personal computer requires a

separate audio connection.

Downloaded From TV-Manual.com Manuals

20 1. Basic Setup and Operation

For assistance call 1(800) 332-2119

Tip

Set the computer’s screen saver to display a pattern

after several minutes of inactivity. This acts as a

reminder that the TV is powered on.

Computer Video Adjustments

Power on the computer.

1.

Select

2.

PC from the Input Selection menu. To do

this, press

INPUT

to open the Input Selection menu,

move the highlight to the PC icon, and press

ENTER.

Working from the computer, change

3.

the resolution of the computer image.

View the computer image on the TV

and maximize the computer resolution

while maintaining a suitable aspect

ratio for the image.

Perform TV video adjustments.

4.

Press

VIDEO

repeatedly to access video-

adjustment options.

Press

5.

FORMAT

repeatedly to find the

picture shape best suited to the

image. See the chart on this page

showing how different computer reso-

lutions can be displayed on the TV.

Image Resolution

Your Mitsubishi TV can display the resolu-

tions shown in the chart from standard

VGA (640 x 480) through 1920 x 1080

signals at a refresh rate of 60 Hz.

In most cases, the computer will select

the best resolution match to display on

the TV. You can override this setting if you

wish. Refer to your computer operating

system’s instructions for information on

changing the screen resolution.

You may need to restart the computer for

changes to take effect.

Using the TV with a Personal Computer

Distortion in Computer Images

Computer images may show distortion

when viewed on the TV, e.g., lines that

should be straight may appear slightly

curved.

Computer Display Formats

Press

FORMAT

repeatedly to cycle through the TV displays available

for your computer’s video signal.

Computer Signal

As Displayed on TV Screen

Original Format

4 X 3

Standard

16 X 9

Standard

Zoom

VGA

640 X 480

SVGA

800 X 600

Original Format Standard Zoom

XGA

1024 X 768

PC 720p

1280 X 720

WXGA

1360 X 768

SXGA

1280 X 1024

Original Format Standard

PC 1080p

1920 X 1080

Downloaded From TV-Manual.com Manuals

Page is loading ...

Unisen 265 User manual

This manual is also suitable for

Unisen 265 User manual

Related papers

Other documents