Weinmann MEDUMAT Standard² Ventilator Operating instructions
- Type
- Operating instructions
Charging station
Instructions for Use
Read the instructions for use before using the product.
Failure to observe the instructions for use can result in serious injuries or death.
67671a.book Seite 1 Donnerstag, 5. Januar 2023 11:21 11
2EN Charging station
WM 67671a 2022-09
Deutsch
Table of Contents
1 Introduction 4
1.1 Intended use ................................................................................. 4
1.2 Contraindications .......................................................................... 4
1.3 Side effects ................................................................................... 4
2 Safety 4
2.1 Safety information ......................................................................... 5
2.2 General instructions ...................................................................... 6
2.3 Warnings in this document ............................................................ 6
3 Description 8
3.1 Overview ....................................................................................... 8
3.2 Accessories ................................................................................... 9
3.3 Charge status display .................................................................. 10
3.4 Symbols ...................................................................................... 11
4 Preparation and operation 13
4.1 Installing the charging station on the wall ................................... 13
4.2 Mobile operation of the charging station ..................................... 14
4.3 Connecting the charging station supply to the line power ............ 14
4.4 Connecting the charging station to a 12 V on-board power
supply ......................................................................................... 15
4.5 Charging the battery in the charging station ................................ 16
5 Hygienic reprocessing 17
5.1 General instructions .................................................................... 17
5.2 Intervals ...................................................................................... 17
5.3 Hygienic preparation of the charging station ................................ 17
6 Function check 18
7 Faults 19
8 Maintenance 21
8.1 General instructions .................................................................... 21
8.2 Intervals ...................................................................................... 21
67671a.book Seite 2 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 3
9 Storage and disposal 21
9.1 Storage ....................................................................................... 21
9.2 Disposal ...................................................................................... 22
10 Appendix 23
10.1 Technical data ............................................................................. 23
10.2 Scope of supply ........................................................................... 24
11 Warranty 25
67671a.book Seite 3 Donnerstag, 5. Januar 2023 11:21 11
4EN Charging station
WM 67671a 2022-09
Introduction
1 Introduction
1.1 Intended use
The charging station is intended solely for charging the WM 45045
battery pack rechargeable battery.
1.2 Contraindications
There are no known contraindications.
1.3 Side effects
There are no known side effects.
2 Safety
The instructions for use form part of the device. If the instructions
for use and the following safety information are not fully complied
with, the treatment may fail or be compromised. This could cause
severe or life-threatening injuries to the patient, user or
bystanders.
Fully comply with the instructions for use.
Keep the instructions for use with the device so that they can
be accessed at any time.
Only use the device as defined by the intended use
(see „1.1 Intended use“, page4).
Do not use the device in the event of contraindications.
Follow the instructions for use for the components and
accessories.
67671a.book Seite 4 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 5
Safety
2.1 Safety information
2.1.1 Safe use of the charging station
Warning Risk of injury if the charging station is used in damp or
electrically conductive surroundings!
Using the charging station in damp or electrically conductive
surroundings or outdoors may result in an electric shock and injury
to the user.
Only use the charging station in a dry place.
Only use the charging station in surroundings that are not
electrically conductive.
Protect the charging station from the ingress of liquids.
Only use the charging station indoors.
2.1.2 Power supply
Warning Reduced operational readiness caused by defective power
cord or power supply unit and charger!
A defective power cord or power supply unit and charger will
prevent the battery from being charged in the charging station,
which means that the equipment powered by the battery will not
be ready to use.
Check the power cord and power supply unit and charger
regularly.
Risk of injury from electric shock!
The contacts in the battery compartment are live. Touching the
contacts may cause electric shock and injure the user.
Do not touch the contacts in the battery compartment.
Caution Risk of injury due to trailing power cord!
A trailing power cord is a trip hazard, which may cause injury and
interrupt operation of the device being used.
During line operation, position the power cord so that there is
no danger of tripping over it.
67671a.book Seite 5 Donnerstag, 5. Januar 2023 11:21 11
6EN Charging station
WM 67671a 2022-09
Safety
2.2 General instructions
• If third-party items are used, malfunctions may occur and
fitness for use may be restricted. Biocompatibility requirements
may also not be met. Please note that in such cases, any
warranty claim and liability will be voided if neither the
accessories recommended in the instructions for use nor
genuine replacement parts are used.
• Repairs, servicing and maintenance should only be carried out
by the manufacturer WEINMANN Emergency.
• Modifications to the charging station should only be carried
out by the manufacturer WEINMANN Emergency.
• Please observe the section on hygienic reprocessing in order to
avoid infection or bacterial contamination (see „5 Hygienic
reprocessing“, page17).
2.3 Warnings in this document
Warnings are used to flag up safety-relevant information.
You will find a warning preceding any action that entails a hazard
for persons or equipment.
Warnings consist of
• the warning symbol (pictogram),
• a signal word designating the hazard level,
• information about the hazard and
• instructions for avoiding the hazard.
67671a.book Seite 6 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 7
Safety
The warnings appear in three hazard levels depending on the
degree of danger:
DANGER!
DANGER indicates a hazardous situation that, if not avoided, will
result in death or serious injury.
WARNING!
WARNING indicates a hazardous situation that, if not avoided,
could result in death or serious injury.
CAUTION!
CAUTION indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
NOTICE!
NOTICE indicates information considered important, but not
hazard-related (e.g., messages related to damage to property or
the environment).
Designates useful information relating to a particular action.
67671a.book Seite 7 Donnerstag, 5. Januar 2023 11:21 11
8EN Charging station
WM 67671a 2022-09
Description
3 Description
3.1 Overview
3-1 Charging station
1
234
5
6
No. Designation Description
1Power connector Connects the charging station to the power supply.
2Cap Closes the power connection.
3Cover cap Covers the 12 V cover cap.
412 V power cord Connects the charging station with the 12 V on-board
power supply in an emergency vehicle.
5Window for charge status display Allows the operator to see the charge status display.
6Line power indicator Shows that the charging station is connected to the
line power.
67671a.book Seite 8 Donnerstag, 5. Januar 2023 11:21 11
10 EN Charging station
WM 67671a 2022-09
Description
3.3 Charge status display
3-3 Charge status display
No. Designation Description
1Fault indicator (red) Lights up if the battery is
defective.
2Charge level LEDs (green) Show the battery charge
status.
3Status button
Activated by pressing the
fault indicator and charge
level LEDs.
Charge level
display on the
battery
Explanation Meaning
4 LEDs are lit Battery charge status
> 90%
3 LEDs are lit Battery charge status
approx. 60% to 90%
2 LEDs are lit Battery charge status
approx. 40% to 60%
1 LED is lit Battery charge status
approx. 10% to 40%
123
67671a.book Seite 10 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 11
Description
The charging station has a window on the front, through which
the charge level display on the battery is visible. This enables the
battery charge status to be checked directly on the battery itself
whilst it is being charged in the charging station.
3.4 Symbols
1 LED is flashing Battery charge status
< 10%
No LEDs are lit
Battery is deeply discharged.
Charge battery in the device
or in the charging station for
24 hours.
Red fault indicator is
lit
Battery is defective. Replace
battery.
Charge level
display on the
battery
Explanation Meaning
Symbol Description
Article number
Serial number
Date of manufacture
CE mark (confirms that the device complies with the applicable European
directives)
Observe the instructions for use.
Follow the instructions for use.
Storage temperature range limits
REF
SN
67671a.book Seite 11 Donnerstag, 5. Januar 2023 11:21 11
12 EN Charging station
WM 67671a 2022-09
Description
Storage humidity range limits
Air pressure range limits
Do not dispose of device in household waste.
Direct current
Type of protection against electric shock: Protection class II device
Inlet
Output
IPX1
Degree of protection against:
• Ingress of solid objects
• Ingress of dust
• Ingress of water with harmful effect
Symbol Description
67671a.book Seite 12 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 13
Preparation and operation
4 Preparation and operation
4.1 Installing the charging station on the
wall
1. Position the charging station with its back against a wall so that
the opening of the battery compartment is facing to the right
or left.
2. Screw the charging station onto the wall with 3 screws and
3 washers (maximum insertion depth 6 mm)
When doing so, note: The screws must be securely tightened.
Result The charging station is installed firmly on the wall.
Risk of injury from incorrectly installed charging station!
If the charging station is installed incorrectly, the charging station
may come loose from the wall or the battery may fall out.
Position the charging station correctly and fasten.
67671a.book Seite 13 Donnerstag, 5. Januar 2023 11:21 11
14 EN Charging station
WM 67671a 2022-09
Preparation and operation
4.2 Mobile operation of the charging
station
1. Adhere the rubber bases to the back of the charging station.
2. Lay the charging station on a flat surface.
Result The charging station is used as a mobile (e.g. table-top) unit.
4.3 Connecting the charging station
supply to the line power
1. Remove the cap from the power connection.
2. Connect the power supply unit and charger WM 28937 to the
power connection.
3. Connect the power supply unit and charger to the line power.
Result The charging station is connected to the line power. The green
power indicator on the charging station is lit.
67671a.book Seite 14 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 15
Preparation and operation
4.4 Connecting the charging station to a
12 V on-board power supply
1. Remove the cover cap on the back of the charging station.
2. Pull the 12 V power cord out of the charging station.
3. Remove the insulation sleeves.
4. Close off the cable entries with a liquid adhesive to prevent the
12 V power cord from slipping back into the charging station,
and to prevent ingress of dirt and water.
5. Connect the red wire of the 12 V power cord to the positive
terminal of the 12 V on-board power supply in the vehicle.
67671a.book Seite 15 Donnerstag, 5. Januar 2023 11:21 11
16 EN Charging station
WM 67671a 2022-09
Preparation and operation
6. Connect the black wire of the 12 V power cord to the negative
terminal of the 12 V on-board power supply in the vehicle.
Result The charging station is connected to the 12 V on-board power
supply in the vehicle. The green power indicator on the charging
station is lit.
4.5 Charging the battery in the charging
station
1. Slide the battery into the charging station until it audibly clicks
into place.
Charging starts automatically if the following conditions are met:
• External power supply with at least 12 V to 15.1 V connected
• Battery is not already fully charged (< 95% charge level)
• Battery temperature between 0°C and 45°C
The battery’s charge level LED flashes green during the
charging procedure.
2. If the charge level LEDs lights up green continuously: unlock
the battery and remove it from the charging station.
Result The battery is fully charged.
67671a.book Seite 16 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 17
Hygienic reprocessing
5 Hygienic reprocessing
5.1 General instructions
• Use suitable gloves for disinfection work (e.g., household or
disposable gloves).
• Please refer to the instructions for use supplied with the
disinfectant used.
5.2 Intervals
Clean the charging station as and when necessary.
5.3 Hygienic preparation of the charging
station
1. Disconnect the charging station from the line power.
2. Remove the battery.
Risk of infection resulting from insufficient hygienic
reprocessing!
If the charging station and accessories are not hygienically
reprocessed correctly or at all, they may cause infection if they
come into contact with the skin, which may cause serious or life-
threatening injury to the patient or the user. Furthermore, the
charging station and accessories may be damaged.
Carry out hygienic reprocessing of the charging station and
accessories after every use.
When hygienically reprocessing the charging station and
accessories, use only the recommended cleaning agents and
disinfectants.
Follow the instructions for use of the cleaning agents and
disinfectants used.
67671a.book Seite 17 Donnerstag, 5. Januar 2023 11:21 11
18 EN Charging station
WM 67671a 2022-09
Function check
3. Carry out hygienic reprocessing of the parts as specified in the
following table:
4. Insert battery.
5. Reconnect to line power.
Result The parts have been hygienically reprocessed.
6 Function check
No function check is required.
Part Level of
disinfection
Manual
Cleaning
Wipe
disinfection
Immersion
disinfection
Mechanical
reprocessing Sterilization
Battery pack
rechargeable
battery
Intermediate
Level
Disinfection
Wipe-down
cleaning with
X-Wipes
(Bode)
neodisher®
MediClean
forte
(Dr. Weigert).
Dosage:
10 ml/l
Duration:
Wipe down
all surfaces at
least twice
until they look
clean.
Wipe down at
least twice
with
Incidin™
OxyWipe S
(Ecolab).
Exposure
time: 5 min Not permitted Not permitted Not permitted
Power supply
unit and
charger
Cleaning
sufficient
Not
applicable
Charging
station for
battery
WM 45045
67671a.book Seite 18 Donnerstag, 5. Januar 2023 11:21 11
WM 67671a 2022-09
Charging station EN 19
Faults
7Faults
If you are not able to clear an error message with the aid of the
table, you should contact the manufacturer
WEINMANN Emergency or a technician specifically authorized by
WEINMANN Emergency to have the charging station repaired. To
avoid serious damage, do not continue using the charging station.
Fault Cause Remedy
Red fault indicator lights up when
status button on battery is pressed
or red battery status indicator on
device lights up
Battery defective Replace battery.
Battery temperature outside the
permitted range (> 70°C)
Use battery within permitted
temperature range (see 10.1.1,
p.23).
Battery does not respond when
status button is pressed.
Battery has run down completely
and has shut down to prevent
deep discharge
Charge the battery in the device or
the charging station for 24 hours
(see 4.5, p.16). After 24 h:
• Green LED is lit: Battery fully
charged and ready for use.
• Red LED or no LED is lit:
Battery defective. Replace
battery.
Device runtime with battery
operation too short
Battery has reached the end of its
service life Replace battery.
Battery not charging although it is
not full
Battery temperature < 0°C or
> 45°C
Charge battery within permitted
temperature range (see 10.1.1,
p.23).
Battery defective Replace battery.
67671a.book Seite 19 Donnerstag, 5. Januar 2023 11:21 11
20 EN Charging station
WM 67671a 2022-09
Faults
Charge status LEDs not flashing,
and battery not charging
Battery not correctly inserted in the
charging station
Check battery.
Insert battery correctly.
Charging station not connected to
the power supply
Connect the charging station
supply to the line power (see 4.3,
p.14).
Connect the charging station to a
12 V on-board power supply (see
4.4, p.15).
Charging station defective Have the charging station
repaired.
Battery charge status at > 95% Press status button on battery to
check battery charge status.
Fault Cause Remedy
67671a.book Seite 20 Donnerstag, 5. Januar 2023 11:21 11
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Weinmann MEDUMAT Standard² Ventilator Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Braun 8585 User manual
-
-
Braun EP 100 User manual
-
-
-
-
Porsche CDR-31 2011 Driver Manual
-
-
Valeo BUS TOP C Operating Instructions Manual
-
Dometic TC14 Mobile Cooling Tropicool User manual