Assembly Instructions
0193817R1 Page 1 of 4
Assembly Instructions
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts or
accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Cooling Fan kit for Immersion XR Cart
99062
(1) Fan assembly
(2) 044207
1” Cord clip
Assembly tip: Do not tighten component fasteners completely
until all have been installed. Keeping them loose will help with
alignment between parts during assembly.
X2
Remove rear panel
1. Unplug power cord.
2. Open the cart doors. Figure 1.1.
3. Locate the (4) rear panel screws and loosen with a Phillips
screwdriver.
1
(1) 0109399
Fan power cord
(2) 059533
10-24 x 1/2”
THMS
Figure 1.1 Figure 1.2
4. Lift up on the rear panel to release screws. Figure 1.2.
5. Remove panel.
0193817R1 Page 2 of 4
1. Choose one of the fan locations below based on the goggles used. Figure 2.
2. Remove any goggles / controllers from the upper drawer
Choose fan mounting location
2
A
Fan location A
• Edupro (primary
recommended location)
• Pico Neo 3 (primary
recommended location)
Fan location B
• Edupro (secondary
recommended location)
Fan location C
• Pico Neo 3 (secondary recommended
location
• Quest 2 Elite* (primary recommended
location)
• Quest 2 Soft* Strap (primary
recommended location)
B
*for Quest 2 goggles, one goggle set clos-
est to the fan will need to be removed to
provide clearance for the fan.
C
Rear panel
Side panel
Power
Switch
Figure 2
0193817R1 Page 3 of 4
1” Cord clip
Figure 3
(2) 10-24 x 1/2”
THM Screws
Fan assembly
Upper vent slot
1. Align the fan assembly mounting holes with the upper vent slot. Figure 3.
2. From the outside, install (2) 10-24 x 1/2” THM screws to secure the fan.
3. Be sure the fan assembly is located at the end of the upper vent slot as shown.
4. Tighten screws securely.
5. Attach the 1” cord clips to the top panel underside and route the fan power cord
to the power switch
Install fan to cart
3
Note: Keep fan disconnected from power during
installation.
A
B
C
Note: All 3 fan mounting locations are shown here for
clarity. Rear panel will be removed during installation.
Rear panel
Connect power cord
1. With two-prong plug end disconnected, plug the fan power cord into the
fan socket. Figure 4.
2. Plug the two-prong plug end of the power cord into the AUX outlet
on the power switch.
4
Figure 4
1” Cord clip
Power Switch
Fan power cord
0193817R1 Page 4 of 4
© 2023 Spectrum Industries Inc., All rights reserved.
1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Replace rear panel
1. Set rear panel back into position and make sure the 4 screws are seated.
2. Tighten the (4) rear panel screws to secure.
5
Note: If removing the rear panel in the future be
aware that the fan power cord will need to be
unplugged before removing. (A or B rear panel
fan mounting locations).
Figure 5
/
