Minka Group 73321-66A User manual

Brand: Minka Group

Model: 73321-66A

Type: User manual

Minka Group 73321-66A is a versatile and stylish lighting fixture that can elevate the ambiance of any room. With its easy installation process and customizable features, it offers a range of possibilities for illuminating your space.

The fixture supports the use of candelabra base bulbs, allowing you to choose the brightness and warmth of the light to suit your preferences. It can accommodate up to 60 watts of power, providing ample illumination for a variety of settings.

The 73321-66A is not only functional but also aesthetically pleasing. Its sleek design and clear caulking feature help prevent moisture from entering the outlet box, ensuring its durability and longevity.

INSTALLATION INSTRUCTIONS

Item#73320/73321-66A (New. 2022/12/30)

READ AND SAVE THESE INSTRUCTIONS

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Page: 1/1

Fig. 1

Fig. 3

Fig. 2

LA-3634E

MOUNTING THE FIXTURE

(Fig. 1)

1. Shut off power at the fuse box or circ

uit breaker box and

remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the

parts in a clean area. Take care not to misplace any

small parts necessary for installation.

3. Attach mounting plate (A) to junction box (not included)

using mounting screws (B) (Size: #8-32N*L0.5”). The

side of the mounting plate marked “GND” must face out.

CONNECTING THE WIRES (Fig. 2)

4. Connect the electrical wires as shown in figure 2

making sure that all wire connectors are secured. If your

junction box

has a ground wire (green or bare copper),

connect fixture’s ground wire to it. Otherwise, connect

fixture’s ground wire directly to mounting plate (A) using

green screw provided.

5. Tuck wire connectors neatly inside the junction box.

COMPLETING THE INSTALLATION (Fig. 1)

6. Place fixture body (D) onto mounting plate (A) followed

by plastic washer (E) and secure with screws (C).

To prevent moisture from entering outlet box and

causing a short, use clear caulking (i.e. Indoor/Outdoor

Silicone Sealant) to outline the outside of fixture

back-

plate where it meets the wall leaving a space at

bottom to allow moisture a means to escape (Fig.3).

8. Install (1) one

candelabra base bulbs (G) up to 60 watts

each or CFL or LED equivalent (not include

d) in

accordance with the fixture specification—DO NOT

EXCEED THE MAXIMUM WATTAGE RATING! (NE

PAS DEPASSER LA PUISSANCE NOMINALE

MAXIMALE!)

9. Place glass shade (H) over socket (F) and twist until

secured on socket cup.

Your installation is now complete. Ret

urn power to the

junction box and test the fixture.

Note:

Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

Set# A-021-118DB

-Mounting Plate

-Ground Screw

-Mounting Screw *2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

CAULKING

BACK PLATE

Minka Group 73321-66A User manual

Minka Group 73321-66A User manual

Minka Group 73321-66A User manual

Related papers

Other documents