George Kovacs P1555-66A-L, a stylish and functional fixture, offers great illumination and adds a touch of elegance to your space. With its dimmable feature, compatible with ELV and/or LED compatible wall dimmer switches, you can adjust the brightness to create the perfect ambiance.
George Kovacs P1555-66A-L, a stylish and functional fixture, offers great illumination and adds a touch of elegance to your space. With its dimmable feature, compatible with ELV and/or LED compatible wall dimmer switches, you can adjust the brightness to create the perfect ambiance.
L
INSTALLATION INSTRUCTIONS
Item#P1555-66A-L P1556-66A-L (Rev. 05/09/2023)
READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION
1.
Carefully remove the fixture from the carton and check that all parts
are included as shown in the illustration.
2.
Shut off power at the circuit breaker and remove the old fixture
including the mounting hardware.
MOUNTING THE FIXYURE (Fig. 1)
3.
Attach mounting plate (A) to the outlet box (not included) using
mounting screws (B) (Size: #8-32N*L1”L) as shown in Fig.1. Note: The
side of mounting plate (A) marked “GND” must face out.
Fig. 1
Set# A-020-120D - B
Mounting plate
-
Ground screw
-
Mounting Screw*2
Rod#
Outlet box
A
T P
C D
F1
4.
Determine the desired hanging height and thread rods (F1, F2) to
coupling (E) on the top of the fixture body. Secure canopy (C) onto
rod (F1). Pass the wires carefully through each rod and canopy. Then
tighten the rods and the canopy assembly until secured.
- W30-H-66A (F1)
- W30-1-66A*3 (F2)
Glass Shade
#PG1555 for item#P1555-66A-L
5.
Adjust the arms to proper position as shown in Fig.3.
6. Align the bottom frame to the bottom of fixture body and secure with
screws (G) using screwdriver (not included). Snap the four decorative
nuts (H) to the bottom frame.
7. Place glass (K) onto fixture body and secure with metal caps (I) and
screws (J).
8. The support cable is provided to support the weight of the fixture while
wiring. Align the fixture to mounting plate (A) and attach hook (T) on the
end of support cable (P) into a slot located on mounting plate (A).
Carefully allow support cable (P) to support the weight of the fixture
while wiring (Fig.1).
#PG1556 for item#P1556-66A-L
F2
K
J
Fixture body
E
CONNECTION THE WIRES (Fig. 2) I
9. Connect the electrical wires as shown in Fig.2, making sure that all
wire connectors are secured. If your outlet box has a ground wire
(green or bare copper), connect the fixture's ground wire to it.
Otherwise, connect the fixture's ground wire directly to the mounting
plate (A) using the green screw provided. After wires are connected,
tuck them carefully inside the outlet box.
FINISHING THE INSTALLATION (Fig. 3)
10.
Align canopy (C) over mounting plate (A). S ecure with screws (D).
Replacing LED module (Fig.4)
The LED module can be replaced by a qualified electrician without
cutting of wire and without damage to any decorative element to
which the fixture is attached. See installation steps for more details
(Fig 3.)
a. Shut off the power.
b. Remove screws (D) and disconnect wire connectors and place fixture
body on a clean surface. (Fig1)
Fig. 2
FIXTURE
WIRES
Smooth
Black or
Bottom frame
FIXTURE
WIRES
Ribbed
White or
G
Screw driver H
FIXTURE
WIRES
Bare
Copper
(Ground)
c. Remove screws (J) and metal caps (I) from the fixture body and
remove glass (K).
d. Press the button with printed ''L'' quick connector on LED module (L)
with screwdriver (not included) to disconnect the black wire and then
disconnect the white wire from the printed ''N'' quick connector on LED
module (L). Carefully remove LED module (L) from the base.
e. Reverse steps a-d for installing the new LED module.
Fig. 3
HOUSE
WIRES
Black
(Hot)
Fig. 4
HOUSE
WIRES
White
(Neutral)
J
I
HOUSE
WIRES
Green
(Ground)
K
Your installation is now complete. Return power to the
outlet box
and test the fixture.
Note: The illustration in figure 1 on this manual is for
installation purposes only. It may or may not be identical to
the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer
switches.
Page: 2/2 P1555-66A-L P1556-66A-L
-
1
-
2
George Kovacs P1555-66A-L, a stylish and functional fixture, offers great illumination and adds a touch of elegance to your space. With its dimmable feature, compatible with ELV and/or LED compatible wall dimmer switches, you can adjust the brightness to create the perfect ambiance.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
George Kovacs P5438-697-L User manual
-
George Kovacs P1558-66A-L User manual
-
George Kovacs P1903-66A-L User manual
-
George Kovacs P1551-66A-L User manual
-
George Kovacs P1077-657-L User manual
-
George Kovacs P1833-077 User manual
-
George Kovacs P1832-077 User manual
-
George Kovacs P1420-674-L User manual
-
George Kovacs P1823-248 Operating instructions
-
George Kovacs P1425-674-L User manual
Other documents
-
VISUAL COMFORT S 2121 User manual
-
Minka Lavery 2745-695 Operating instructions
-
Minka Lavery 5036-66A User manual
-
Minka Group P1558-66A-L User manual
-
-
-
-
Minka Lavery 3860-726 Operating instructions
-
-
