Assembly Instruction
CAST ALUMINIUM
PATIO SOFA CHAIR
Elm Plus, LLC
1
Bolt (G)
Nut Cap (K)
Washer (H) Spring Washer (I) Nut (J)
HARDWARE LIST
PRE-ASSEMBLY PREPARATION
WARNING! DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER ENTRAPMENT
• Please read through this instruction before beginning assembly.
• Two adults assembly is recommended.
• Clear out the space for assembly and lay out all parts base on Parts List, extra room will allow you to easily
determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembly.
• Do not fully tighten th
e bolts until all have been inserted and hand tightened.
• Please check for any loose screws and tighten them before use.
PANEL AND FITTINGS IDENTIFICATION
Backrest Panel (A) Right Arm Panel (B) Left Arm Panel (C)
Qty: 1Qty: 1
Back Cushion (E) Seat Cushion (F)
Qty: 1Qty: 1
Qty: 1
Qty: 5
Bolt (L)
Qty: 5
Qty: 5
Qty: 5
Qty: 5 Qty: 5
Seat Panel (D)
Qty: 1
M6*30mm
M6 M8*32mm
M6 M6 M6
Washer (M) Spring Washer (N)
Qty: 5 Qty: 5
M8 M8
2
B
D
L
O
R
N
M
Step 1
Place the Right Arm Panel (B) with its one side face skywards onto a clean, soft surface
to avoid any scratches or damages to the product.
Attach Seat Panel (D) to Right Arm Panel (B) by using 2 Bolts (L), 2 Washers (M), 2 Spring
Washers (N), 2 Nuts (O) with Wrench (R) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
Nut (O) Nut cap (P) Wrench (Q) Wrench (R)
Qty: 5Qty: 5 Qty: 1 Qty: 1
M8 M8 M6 M8
L X 2 M X 2 N X 2 O X 2
3
Step 2
Attach Left Arm Panel (C) to Seat Panel (D) by using 2 Bolts (L), 2 Washers (M), 2 Spring
Washers (N), 2 Nuts (O) with Wrench (R) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
Attach Backrest Panel (A) to Right Arm Panel (B) and Left Arm Panel (C) by using 4 Bolts
(G), 4 Washers (H), 4 Spring Washers (I), 4 Nuts (J) with Wrench (Q) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
Step 3
D
L X 2 M X 2 N X 2 O X 2
G X 4 H X 4 I X 4 J X 4
B
C
D
L
NM O R
B
A
G
Q
J
I
H
C
4
Now fully and securely tighten all nuts at all joints.
Put the Nut caps (K) and (P) on the Nut as shown below.
Step 4
K X 4 P X 4
Adjust the Pre-installed levellers at the bottom of the chair legs until the chair is level
with the ground.
Step 5
Adjust height
for balance
Adjust low
for balance
Adjust Pre-installed Levellers
height for balance
K
P
5
E
F
Step 6
Put Back Cushion (E) and Seat Cushion (F) on the Chair. Your Chair is ready for use.
Inspect it and make sure all parts are adequately connected.
Assembly Instruction
CAST ALUMINIUM PATIO
SIDE TABLE
Elm Plus, LLC
Assembly Instruction
CAST ALUMINIUM PATIO
COFFEE TABLE
Elm Plus, LLC
1
Bolt (D)
Nut Cap (H)
Washer (E) Spring Washer (F) Nut (G)
HARDWARE LIST
PRE-ASSEMBLY PREPARATION
WARNING! DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER ENTRAPMENT
• Please read through this instruction before beginning assembly.
• Two adults assembly is recommended.
• Clear out the space for assembly and lay out all parts base on Parts List, extra room will allow you to easily
determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembly.
• Do not fully tighten th
e bolts until all have been inserted and hand tightened.
• Please check for any loose screws and tighten them before use.
PANEL AND FITTINGS IDENTIFICATION
Table Top (A) Legs Support (B) Table Leg (C)
Qty: 1Qty: 1 Qty: 4
Qty: 9
Wrench (I)
Qty: 1
Qty: 5
Qty: 9
Qty: 9 Qty: 9
M8*35mm
M8 M8
M8 M8 M8
2
Step 1
Lay the Table Top (A), facedown, onto a flat, soft, clean surface.
Attach the Table Leg (C) to the Table Top (A) by using 4 Bolts (D), 4 Washers (E), 4 Spring
Washers (F), 4 Nuts (G) with Wrench (I).
Repeat same step for attaching the remaining 3 legs to the Table Top (A).
DO NOT OVERTIGHTEN.
Step 2
Loosely attach the Legs Support (B) to Table Leg (C) by using 4 Washers (E), 4 Spring
Washers (F), 4 Nuts (G) with Wrench (I).
Repeat same step for all contact points of the Table Legs and Legs Support.
DO NOT OVERTIGHTEN.
X4
X4
D X 4 E X 4 F X 4 G X 4
E X 4 F X 4 G X 4
C
B
A
GI F E
A
C
D
A
C
I
G
F
E
3
Step 3
Now fully and securely tighten all nuts at all joints.
Add Nut Caps (H) on all bolt ends to protect skin or clothing from getting snagged.
Stand the table right side up.
Adjust the Legs pre-installed Levellers until the Table is level with the ground.
Step 4
H X 8
Adjust height
for balance
Adjust low
for balance
Adjust Pre-installed Levellers
height for balance
H
H
4
Step 5
Caution: This TABLE can only be used on a flat, level surface.
1
Washer (D)
Wrench (H)
Spring Washer (E) Nut (F) Nut Cap (G)
HARDWARE LIST
PRE-ASSEMBLY PREPARATION
WARNING! DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER ENTRAPMENT
• Please read through this instruction before beginning assembly.
• Two adults assembly is recommended.
• Clear out the space for assembly and lay out all parts base on Parts List, extra room will allow you to easily
determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding
smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembly.
• Do not fully tighten the bolts until all have been inserted and hand tightened.
• Please check for any loose screws and tighten them before use.
PANEL AND FITTINGS IDENTIFICATION
Leg (A) Table Top (B) Table Bottom (C)
Qty: 1Qty: 4 Qty: 1
Qty: 8Qty: 8
Qty: 1
Qty: 8 Qty: 8
Step 1
Attach 4 Legs (A) to backside of Table Top (B) by using Washer (D), Spring Washer (E)
and Nut (F). Do not make all bolts tightened or put Nut Cap (G).
Step 2
Connect Table Bottom (C) to 4 Legs (A) by using Washer (D), Spring Washer (E)
and Nut (F).
A
H
G
F
E
D
B
BB
A
H
C
G F
E
D
D X 4 E X 4 F X 4 G X 4
D X 4 E X 4 F X 4 G X 4
Step 3
Finally put Nut Cap (G) until all parts have been connected and bolts are tightened.
Assembly Instruction
CAST ALUMINIUM PATIO
LOVESEAT CHAIR
Elm Plus, LLC
1
Bolt (H)
Nut Cap (L)
Washer (I) Spring Washer (J) Nut (K)
HARDWARE LIST
PRE-ASSEMBLY PREPARATION
WARNING! DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER ENTRAPMENT
• Please read through this instruction before beginning assembly.
• Two adults assembly is recommended.
• Clear out the space for assembly and lay out all parts base on Parts List, extra room will allow you to easily
determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembly.
• Do not fully tighten th
e bolts until all have been inserted and hand tightened.
• Please check for any loose screws and tighten them before use.
PANEL AND FITTINGS IDENTIFICATION
Backrest Panel (A) Right Arm Panel (B) Left Arm Panel (C)
Qty: 1Qty: 2
Middle Arm Panel (E) Back Cushion (F)
Qty: 2Qty: 1
Qty: 1
Seat Cushion (G)
Qty: 2
Qty: 9
Bolt (M)
Qty: 5
Qty: 9
Qty: 9
Qty: 9 Qty: 9
Seat Panel (D)
Qty: 2
M6*28mm
M6 M8*30mm
M6 M6 M6
Bolt (N) Washer (O)
Qty: 3 Qty: 7
M8*45mm M8
2
D
T
Q
P
O
Spring Washer (P) Nut (Q) Nut cap (R) Wrench (S)
Qty: 7Qty: 7 Qty: 7 Qty: 1
M8
Wrench (T)
Qty: 1
M8
M8 M8 M6
Step 1
Stand Left Arm Panel (C) up.
Attach Left Arm Panel (C) to Seat Panel (D) by using 2 Bolts (M), 2 Washers (O),
2 Spring Washers (P), 2 Nuts (Q) with Wrench (T) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
M X 2 O X 2 P X 2 Q X 2
C
M
3
Step 2
Attach Seat Panel (D) to Middle Arm Panel (E) by using 2 Bolts (N), 2 Washers (O),
2 Spring Washers (P), 2 Nuts (Q) with Wrench (T) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
Attach Right Arm Panel (B) to Seat Panel (D) by using 2 Bolts (M), 2 Washers (O), 2 Spring
Washers (P), 2 Nuts (Q) with Wrench (T) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
Step 3
D
M
N X 2 O X 2 P X 2 Q X 2
B
T
Q
P
O
D
N
O
O
P
Q
T
E
M X 2 O X 2 P X 2 Q X 2
4
Attach Backrest Panel (A) to Left Arm Panel (C) and Middle Arm Panel (E) by using
4 Bolts (H), 4 Washers (I), 4 Spring Washers (J), 4 Nuts (K) with Wrench (S) as shown
below.
DO NOT FULLY TIGHTEN BOLTS.
Step 4
Repeat step 4 to attach the other Backrest Panel(A) to Right Arm Panel(B).
DO NOT FULLY TIGHTEN BOLTS.
Step 5
H X 4 I X 4 J X 4 K X 4
H X 4 I X 4 J X 4 K X 4
H
A
S
K
J
I
C
A
H
S
K
J
I
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Gromell Palue (77VM006) User manual
-
Regency 1007BK Installation guide
-
Home Styles 5600-802 Operating instructions
-
LOKATSE AC18804D Operating instructions
-
Furniture of America IDF-AC6709BK Installation guide
-
Benjara BM273196 Operating instructions
-
ROOMS TO GO 10551340 Assembly Instructions
-
-
HomeSullivan 40E468F32S Installation guide
-
