ANZZI L-AZ006 Installation guide

ANZZI
Brand
ANZZI
Model
L-AZ006
Type
Installation guide

This manual is also suitable for

ASME A112.18.1/CSA B125.1
Th e tool s m ig ht b e app li ed t o t h e fo ll ow in g p laces:
PA RT NAM ENO .
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Allen key
Aerator wrench
12
15
16
17
Handle assembly
Lock nut
Washer
Plate
Screw
Gasket
Cartridge(hot water)
Shank
O-ring
Spout
Lock nut
Cartridge(cold water)
Aerator
Diverter cover
TWO HA NDL E LAVATORY FA UCET
1
2
3
4
5
8
9
10
6
7
11
13
14
Washer
Adjustable Wrench
RECOMMENDED TOOL S
At tent io n:
fo r easy in st allati on , yo u will need:
1.To read all th e in st allati on in st ru ct io n co mp letely befo re
begi nn in g.
2.To read all th e warn in g, attent io n and mait enance
in fo rm atio n.
3.To purc hase th e pr op er supp ly li nes.
Allen key
WARNING:
Please keep the
tool for future
use!
Teflon tape
Screw Knife Channel Locks
Silicone
Goggles
L-AZ006
Installation Guide
For more information visit www.ANZZI.com or call 1-844-44-ANZZI
Step 1 Faucet and pop-up installation
3
2
1
2
2.Check all connections at arrows for leaks, re-tighten it if necessary.
BUT DON'T OVERTIGHTEN
Step 3 Cleaning and care
Daily cleaning and care are required in order to keep the product shining and
properly working.
1
2
3
4
Clean it with water and dry it with soft cloth.
Clean the product with gentle liquid or glass cleaner.
Don't use acid cleaner.
Don't clean with abrasive material, abrasive paper or knife.
1
1.
and flush water lines for one minute. Reinstall aerator by aerator wrench.
Remove the aerator by aerator wrench. Turn the faucet handle all the way on, turn on hot and cold water supply
A B
2
1
1/2”(13mm)IPS
Step 2 Checking and testing
Faucet installation
Pop-up installation
1.
the lock nut by hand. If the basin is uneven, please use silicone under the gasket.
Place the faucet and gasket on the basin, from underside of basin, assemble the washer and lock nut, tighten
2.Connect the supply lines to the faucet and secure the nuts by .adjustable wrench
Warning: Supply line #1 is for hot water, supply line #2 is for cold water, don't mix up.
Warning: The supply lines mentioned in the previous step are not included. Please purchase them from
the plumbshop.
3.You can use 1/2” IPS faucet connections A, or use the coupling nuts with 3/8" O.D.ball-nose risers B.
1.Remove pop-up drain stopper, and flange with top rubber washer for pop-up assembly. Insert drain body from
underneath of sink drain hole. Replace flange and top rubber washer back to drain body. Tighten flange as far as
possible. Remove and put silicone along bottom of. (Optional) Slide bottom rubber washer on drain body up against
bottom of sink. Tighten washer and locknut firmly against base for tight seal. Remove tailpiece from drain body, add
Teflon tape, replace tailpiece.
2.Replace pop-up drain stopper to drain body with o-ring in place, and align stopper hole with guide rod opening.
3.Remove rod guide nut and rod ball plastic gasket. Insert horizontal rod into drain body and through hole in drain
stopper. Replace rod guide nut with rod ball plastic gasket and tighten it.
rod guide nut rod ball
plastic
gasket
drain
stopper
hole
drain body
o-ring
sink
drain stopper
flange
align hole in
drain stopper
with guide rod
opening
(pointed toward
back wall)
flange
drain body
top rubber washer
sink base
locknut
washer
bottom
rubber
washer
tailpiece
horizontal rod
drain body
1
2
3 4
lift rod
faucet
body
extend rod
horizontal rod
screw
fittings
4.Insert lift rod through hole on faucet body. Connect extend rod to lift rod. Attach horizontal rod to extend rod using
fittings, tighten screw.
  • Page 1 1
  • Page 2 2

ANZZI L-AZ006 Installation guide

ANZZI
Brand
ANZZI
Model
L-AZ006
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents