George Kovacs P1170-617-L User manual

Brand
George Kovacs
Model
P1170-617-L
Type
User manual
INSTALLATION INSTRUCTIONS
FOR P1170-617-L
FOR LED Pendant Light
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R
Page: 1/2
Fig. 2
PREPARING FOR INSTALLATION
1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in
a clear area. Take care not to misplace any small parts
necessary for installation.
INSTALLATION (Fig. 1)
3. Remove the four mounting screws (DD) from the side of the
canopy (A) and remove the mounting plate (BB).
4. Press the wire restraint (B) on the canopy (A) to adjust the
cables (C) to desired length. Press the wire restraint (F) onto
the canopy (A) to adjust the fixture wire (E) length. The fixture
wire (E) should be longer than the cables (C).
5. Attach the mounting plate (BB) to the outlet box (not
provided). Mark on the ceiling where the support screw holes
are located. Remove the mounting plate (BB).
6. Drill pilot holes in the ceiling with a 1/4 in. drill bit. Push the
plastic anchors (FF) into the holes.
7. Secure the mounting plate (BB) to the outlet box (not
included) with the outlet box screws (CC). Tighten until snug.
Screw the wood screws (EE) into the plastic anchors(FF).
CONNECTING THE WIRES (Fig. 2)
8. Connect the electrical wires as shown in Fig. 2, making
sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the mounting plate (BB)
using the green screw (AA) provided. Tuck the wire
connections neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
9. Attach the canopy (A) to the mounting plate (BB) and secure
it with the mounting screws (DD).
Your installation is now complete. Return power to the
junction box and test the fixture.
IMPORTANT: Fixture should be installed by a qualified electrician to
ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall dimmer switches.
.
Fig.1
set#A-021-116420
- Mounting plate
- Ground screw
- Mounting screws*4pcs
- Plastic anchor*2pcs
- Wood screws*2pcs
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Fig.3
Page: 2/2
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified
electrician without cutting of wire and without damage
to any decorative element to which the fixture is
attached. See installation steps for more details
(Fig.3.)
a. Shut off power. Remove the four mounting screws
(DD) from the side of the canopy (A).
b. Disconnect the wires by removing wire nuts. Take
the whole fixture down to the working table.
c. Disconnect the wires of the driver by removing
wire nuts. Press the wire restraint (F) on the
canopy (A) to release the wire (E) out from the
canopy (A).
d. Remove the screws (GG) from the fixture body
(D).
e. Remove the four screws (II) from the four barrels
(HH)
f. Remove the four screws (JJ) from the four barrels
(KK)
g. Remove top plate (G) with the LED board and wire
(E).
h. Reverse steps a-g for installing the new LED
module.
Note: The LED module should be provided by a
specified supplier.
  • Page 1 1
  • Page 2 2

George Kovacs P1170-617-L User manual

Brand
George Kovacs
Model
P1170-617-L
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents