3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2005 by Harbor Freight Tools
®.
All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
ASSEMBLY INSTRUCTIONS
COAT RACK
93049
SKU 93049 For technical questions, please call 1-800-444-3353. Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the
front cover. Keep the manual and invoice in a safe and dry place for future
reference.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Keep work area well lit.
3. Check for damaged parts. Before using any product, any part that
appears damaged should be carefully checked to determine that it will
perform its intended function. Check for any broken or damaged parts and
any other conditions that may affect its operation. Replace or repair
damaged or worn parts immediately.
4. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
5. Always check hardware and assembled parts after assembling. All
connections should be tight and hardware tightened.
6. Keep children away. Children must never be allowed in the work area. Do
not let them play with or climb on the Coat Rack; this product could tip over,
resulting in personal injury and/or property damage. Children must be
supervised around the Coat Rack.
7. Dress Properly. Non skid footwear are recommended when assembling
this product. Wear restrictive hair covering to contain long hair.
8, Use eye protection. Always wear ANSI approved impact safety goggles
when setting up this product.
Materials
Overall Dimensions
Hanger Hooks
Net Weight
Overall Max. Weight Capacity
Hardwood with Dark Red Cherry Stain Finish
73.6”H x 19.8”W
11”H x 9”W x 7/8”T–Qty. 5
9.2 Lbs.
50 Lbs.
SKU 93049 For technical questions, please call 1-800-444-3353. Page 3
9. Maintain products with care. After assembly, position the Coat Rack in a
flat, level area away from a fireplace or heating vent. Position coats, hats,
scarfs, umbrellas, etc. evenly. When some articles are removed, re-arrange
articles to distribute the load. Do not exceed the weight capacity of 50 lbs.
10. Use the right product for the job. Do not overload the Coat Rack. There
are certain applications for which this product was designed. Do not modify
this product and do to use this product for a purpose for which it was not
intended.
11. Do not set up the Coat Rack if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgement or
reflexes are impaired while taking drugs. If there is any doubt, do not set up
the Coat Rack.
Warning: The warnings, cautions, and instructions discussed in this instruc-
tion manual cannot cover all possible conditions and situations that may oc-
cur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator.
Unpacking
When unpacking the Coat Rack, check to make sure that all parts are
included as shown in the parts list. If any parts are missing or broken,
please call Harbor Freight Tools at the number below
Assembly
1. Unpack and arrange all the parts of the Coat Rack on a smooth covered
surface to avoid scratches while assembling.
2. Connect the five Top Hooks (A) to the Upper Swivel Post (F) using a phillips-
head screwdriver and the five Screws (H). Tighten hardware.
See Figure 1
.
Figure 1
SKU 93049 For technical questions, please call 1-800-444-3353. Page 4
3. Place one Horizontal Ring (C) on
the inside of the five Top Hooks
(A). Match up the predrilled holes
in the Ring and the holes in the
Hooks. Secure with the five
Screws (H) in each hole. Tighten
hardware.
See Figures 2 & 3.
Figure 2
4. Match up the predrilled holes in
the four Legs (B) to the holes in
the Lower Post (G). Secure using
the Screws (I) in each hole (two
per leg). Tighten hardware.
See Figure 4.
Figure 4
Figure 3
SKU 93049 For technical questions, please call 1-800-444-3353. Page 5
5. Place one Horizontal Ring (D) on the top
of the four Legs (B). Lay the Coat Rack on
it’s side and match up the predrilled holes
in the Ring and the holes in the Legs.
Secure from underneath the ring with the
four Screws (H) in each hole. Tighten
hardware.
See Figure 5.
Figure 5
6. Place one Horizontal Ring (D) on the
bottom of the four Legs (B). Match up
the predrilled holes in the Ring and the
holes in the Legs. Secure from
underneath the Ring with the four
Screws (I) in each hole. Tighten
hardware. While on it’s side, tap on the
four Rubber Feet (J) on each Leg (B)
and stand the Coat Rack upright.
See Figures 6 & 7.
Figure 6
Figure7
Bottom
Ring (E)
View of
Screws
(I)
Rubber
Feet (J)
SKU 93049 For technical questions, please call 1-800-444-3353. Page 6
Maintenance
1. To remove dust, use a soft cloth and furniture polish.
2. This product should be assembled and stored in a dry area.
7. Locate the hole in the Upper Swivel Post (F) assembly with Hooks (A)
and
place onto the dowel in the Lower Post (G). Apply pressure to secure.
See Figure 8.
Figure 8
Upper Post
Assembly
Dowel in Lower
Post (G)
Caution: Do not place too many garments on the Coat Rack; overloading on
one side, or exceeding the maximum recommended weight capacity of
50 lbs. could result in the Coat Rack tipping over.
SKU 93049 For technical questions, please call 1-800-444-3353. Page 7
Parts List
SKU 93049 For technical questions, please call 1-800-444-3353. Page 8
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
Parts List
Parts Identification
Part # Description Qty.
A
B
C, D, E
F
G
H
I
J
Top Hooks
Legs
Horizontal Rings
Upper Swivel Post
Lower Post
Screws
Screws
Rubber Feet
5
4
1 ea.
1
1
14
12
4
Part A
Part E
Part B
Part H
Part F
Part G
Part D
Part C
Part J
Part I
/