Fagor CNC 8065 for lathes Owner's manual

(Ref: 2008)

8060

8065

CNC

Panel PC.

BLANK PAGE

ꞏ2ꞏ

MACHINE SAFETY

It is up to the machine manufacturer to make sure that the safety of the machine

is enabled in order to prevent personal injury and damage to the CNC or to the

products connected to it. On start-up and while validating CNC parameters, it

checks the status of the following safety elements. If any of them is disabled, the

CNC shows the following warning message.

• Feedback alarm for analog axes.

• Software limits for analog and sercos linear axes.

• Following error monitoring for analog and sercos axes (except the spindle)

both at the CNC and at the drives.

• Tendency test on analog axes.

FAGOR AUTOMATION shall not be held responsible for any personal injuries or

physical damage caused or suffered by the CNC resulting from any of the safety

elements being disabled.

DUAL-USE PRODUCTS

Products manufactured by FAGOR AUTOMATION since April 1st 2014 will

include "-MDU" in their identification if they are included on the list of dual-use

products according to regulation UE 428/2009 and require an export license

depending on destination.

TRANSLATION OF THE ORIGINAL MANUAL

This manual is a translation of the original manual. This manual, as well as the

documents derived from it, have been drafted in Spanish. In the event of any

contradictions between the document in Spanish and its translations, the wording

in the Spanish version shall prevail. The original manual will be labeled with the

text "ORIGINAL MANUAL".

HARDWARE EXPANSIONS

FAGOR AUTOMATION shall not be held responsible for any personal injuries or

physical damage caused or suffered by the CNC resulting from any hardware

manipulation by personnel unauthorized by Fagor Automation.

If the CNC hardware is modified by personnel unauthorized by Fagor

Automation, it will no longer be under warranty.

COMPUTER VIRUSES

FAGOR AUTOMATION guarantees that the software installed contains no

computer viruses. It is up to the user to keep the unit virus free in order to

guarantee its proper operation. Computer viruses at the CNC may cause it to

malfunction.

FAGOR AUTOMATION shall not be held responsible for any personal injuries or

physical damage caused or suffered by the CNC due a computer virus in the

system.

If a computer virus is found in the system, the unit will no longer be under warranty.

transcribed, stored in a backup device or translated into another language

without Fagor Automation’s consent. Unauthorized copying or distributing of this

software is prohibited.

The information described in this manual may be subject to changes due to

technical modifications. Fagor Automation reserves the right to change the

contents of this manual without prior notice.

All the trade marks appearing in the manual belong to the corresponding owners.

The use of these marks by third parties for their own purpose could violate the

rights of the owners.

It is possible that CNC can execute more functions than those described in its

associated documentation; however, Fagor Automation does not guarantee the

validity of those applications. Therefore, except under the express permission

from Fagor Automation, any CNC application that is not described in the

documentation must be considered as "impossible". In any case, Fagor

Automation shall not be held responsible for any personal injuries or physical

damage caused or suffered by the CNC if it is used in any way other than as

explained in the related documentation.

The content of this manual and its validity for the product described here has been

verified. Even so, involuntary errors are possible, hence no absolute match is

guaranteed. However, the contents of this document are regularly checked and

updated implementing the necessary corrections in a later edition. We appreciate

your suggestions for improvement.

The examples described in this manual are for learning purposes. Before using

them in industrial applications, they must be properly adapted making sure that

the safety regulations are fully met.

Panel PC.

CNC 8060

CNC 8065

ꞏ3ꞏ

(REF: 2008)

INDEX

About the product - CNC 8060 ..................................................................................................... 5

About the product - CNC 8065 ..................................................................................................... 9

Declaration of CE conformity and warranty conditions ............................................................... 15

Version history - CNC 8060 ........................................................................................................ 17

Version history - CNC 8065 ........................................................................................................ 19

Safety conditions ........................................................................................................................ 21

Returning conditions ................................................................................................................... 25

CNC maintenance ...................................................................................................................... 27

CHAPTER 1 PREVIOUS INFORMATION.

CHAPTER 2 PPC-21W.

2.1 Specifications. ............................................................................................................... 32

2.2 General diagram (PPC-21W)......................................................................................... 33

2.2.1 Networking, without access to the company network. .............................................. 33

2.2.2 Connecting to an Ethernet network through a switch. ............................................... 34

2.3 Dimensions. .................................................................................................................. 35

2.4 Enclosure and mounting of the module. ........................................................................ 36

2.4.1 Ambient characteristics of the enclosure. .................................................................. 36

2.4.2 Enclosure design........................................................................................................ 36

2.4.3 Securing the module. ................................................................................................. 38

2.5 Voltage supply for the module. ...................................................................................... 40

2.6 Hardware functionalities................................................................................................. 41

2.6.1 Rear keyboard. .......................................................................................................... 41

2.6.2 Monitor (lower end connectors). ................................................................................ 42

2.6.3 Panel PC (lower end connectors). ............................................................................ 43

2.6.4 Panel PC (top end connectors). ................................................................................ 46

2.7 Configuring the video signal from the monitor. .............................................................. 47

2.8 Connection..................................................................................................................... 48

2.8.1 VGA video signal........................................................................................................ 48

2.8.2 Touch controller. ....................................................................................................... 49

2.8.3 Ethernet (Fast Ethernet / Gigabit Ethernet)................................................................ 50

2.9 OSD (On Screen Display) menu.................................................................................... 52

2.9.1 Using the rear keyboard with the OSD menu............................................................. 52

2.9.2 OSD menu. ................................................................................................................ 53

2.9.3 Locks and unlocks the OSD menu............................................................................. 58

CHAPTER 3 PPC-19.

3.1 Specifications................................................................................................................. 60

3.2 General diagram (PPC-19 ). .......................................................................................... 61

3.2.1 Point-to-point connection with the CNC. ................................................................... 61

3.2.2 Connecting to an Ethernet network through a switch. ............................................... 62

3.3 Dimensions. .................................................................................................................. 63

3.4 Enclosure and mounting of the module. ........................................................................ 64

3.4.1 Ambient characteristics of the enclosure. .................................................................. 64

3.4.2 Enclosure design........................................................................................................ 64

3.4.3 Securing the module. ................................................................................................. 66

3.5 Voltage supply for the module. ..................................................................................... 67

3.6 Hardware functionality. Connectors. ............................................................................. 68

3.7 Connection..................................................................................................................... 70

3.7.1 Ethernet (Fast Ethernet / Gigabit Ethernet). .............................................................. 70

CHAPTER 4 FAGORCONNECT APPLICATION.

4.1 Installing the application................................................................................................. 71

4.2 The FagorConnect application....................................................................................... 72

4.3 Configure the application. .............................................................................................. 73

4.4 Work modes................................................................................................................... 74

4.5 Diagnosis. ...................................................................................................................... 75

4.6 Accessing Panel PC resources from the CNC............................................................... 75

Panel PC.

CNC 8060

CNC 8065

ꞏ4ꞏ

(REF: 2008)

Panel PC.

CNC 8060

CNC 8065

ꞏ5ꞏ

(REF: 2008)

ABOUT THE PRODUCT - CNC 8060

BASIC CHARACTERISTICS.

(*) TTL / Differential TTL / Sinusoidal 1 Vpp / SSI protocol / FeeDat / EnDat

Basic characteristics. 8060

FL

M

8060

Power

M

8060

FL

T

8060

Power

T

8060

Power

L

8060

Power

GL

Number of axes. 3 to 4 3 to 6 3 to 4 3 to 6 3 to 6 3 to 6

Number of spindles. 1 1 to 2 1 to 2 1 to 3 1 1

Maximum number of axes and spindles. 5 7 5 7 7 7

Interpolated axes. 4 4 4 4 4 4

Number of tool magazines. 1 1 1 1 to 2 1 1

Number of execution channels. 1 1 1 1 to 2 1 1

Number of handwheels. 1 to 3

Type of servo system. Analog / Sercos Digital

Communications. RS485 / RS422 / RS232

Ethernet

Integrated PLC.

PLC execution time.

Digital inputs / Digital outputs.

Marks / Registers.

Timers / Counters.

Symbols.

< 1ms/K

1024 / 1024

8192 / 1024

512 / 256

Unlimited

Block processing time. < 2.0 ms < 1.5 ms < 2.0 ms < 1.5 ms < 1 ms < 1.5 ms

Remote modules. RIOW RIO5 RIOR RCS-S RIOW-E

Inline

Communication with the remote modules. CANopen CANopen CANopen Sercos EtherCAT

Digital inputs per module. 8 24 / 48 48 - - - 8

Digital outputs per module. 8 16 / 32 32 - - - 8

Analog inputs per module. 4 4 - - - - - - 4

Analog outputs per module. 4 4 - - - 4 2

Inputs for PT100 temperature sensors. 2 2 - - - - - - - - -

Feedback inputs. - - - - - - - - - 4 (*) - - -

Panel PC.

CNC 8060

CNC 8065

ꞏ6ꞏ

(REF: 2008)

SOFTWARE OPTIONS.

Some of the features described in this manual are dependent on the acquired software options. The active

software options for the CNC can be consulted in the diagnostics mode (accessible from the task window

by pressing [CTRL] [A]), under software options.

Consult the ordering handbook for information on the software options available for your model.

SOFT 8060 ADDIT AXES

Additional shaft.

Add axes to the default configuration.

SOFT 8060 ADDIT SPINDLES

Additional spindle.

Add spindles to the default configuration.

SOFT 8060 ADDIT TOOL MAGAZ

Additional tool magazine.

Add tool magazines to the default configuration.

SOFT 8060 ADDIT CHANNELS

Additional channel.

Add channels to the default configuration.

SOFT DIGITAL SERCOS

Sercos digital bus.

SOFT i4.0 CONNECTIVITY PACK

Industry 4.0.

This option allows for the use and capture of data using the

FSYS.

SOFT EDIT/SIMUL

EDISIMU mode (editing and simulation).

It allows for the editing, modification and simulation of a

part-program.

SOFT TOOL RADIUS COMP

Radius compensation.

Tool compensation allows programming the contour to be

machined based on part dimensions of the and without

taking into account the dimensions of the tool that will be

used later on. This avoids having to calculate and define

the tool path based on the tool radius.

SOFT PROFILE EDITOR

Profile editor.

Allows for the part profiles to be edited graphically and to

import dxf files.

SOFT 60 F3D GRAPHICS

F3D graphics.

High definition solid 3D graphics for the execution and

simulation of part-programs and canned cycles of the

editor.

During machining, the F3D graphics display the tool

removing the material from the part in real time, allowing

for the condition of the part to be seen at all times. F3D

graphics can display up to 4 views of the part, where each

can be rotated, zoomed in or zoomed out. Measurements

can also be made on the part and even sections on the

piece from any angle.

SOFT 60 IIP CONVERSATIONAL

Interactive Icon-based Pages (conversational mode).

IIP or conversational mode is specifically designed for

people without any prior programming knowledge or for

those that are not familiarized with Fagor CNC's.

Working in conversational mode is easier than in ISO

mode, as it ensures proper data entry and minimizes the

number of operations to be defined. There is no need to

work with part-programs.

SOFT 60 RTCP

Dynamic RTCP (Rotating Tool Center Point).

The dynamic RTCP option is required for interpolation

machining with 4, 5 or 6 axis.

SOFT 60 C AXIS

C axis.

It activates the kinematics for working with the C axis and

the associated canned cycles. The CNC can control

several C axes. The parameters of each axis indicate if it

will function as a C axis or not, where it will not be

necessary to activate another axis for the machine

parameters.

SOFT 60 Y AXIS

Y axis for lathe.

It activates the kinematics for working with the Y axis and

the associated canned cycles.

Panel PC.

CNC 8060

CNC 8065

ꞏ7ꞏ

(REF: 2008)

SOFT 60 TANDEM AXES

Tandem axes.

A tandem axis consists in two motors mechanically

coupled (slaved) and making up a single transmission

system (axis or spindle). A tandem axis helps provide the

necessary torque to move an axis when a single motor is

not capable of supplying enough torque to do it.

When activating this feature, it should be kept in mind that

for each tandem axis of the machine, another axis must be

added to the entire configuration. For example, on a large

3-axis lathe (X Z and tailstock), if the tailstock is a tandem

axis, the final purchase order for the machine must

indicate 4 axes.

SOFT 60 SYNCHRONISM

Synchronization of axes and spindles.

The axes and ballscrews may be synchronized in two

ways: in terms of speed or position. The CNC

configuration takes into consideration the synchronization

of 2 axes or 2 spindles. Once synchronized, only the

master displays and programs the element.

SOFT 60 HSSA I MACHINING SYSTEM

High Speed Surface Accuracy.

This is the new version of algorithms for high speed

machining (HSC). This new HSSA algorithm allows for

high speed machining optimization, where higher cutting

speeds, smoother contours, a better surface finishing and

greater precision are achieved.

SOFT 60 HSSA II MACHINING SYSTEM

HSSA-II machining system.

This is the new version of algorithms for high speed

machining (HSC). This new HSSA algorithm allows for

high speed machining optimization, where higher cutting

speeds, smoother contours, a better surface finishing and

greater precision are achieved.

SOFT 60 PROBE

Probing canned cycles.

The CNC may have two probes; usually a tabletop probe

to calibrate tools and a measuring probe to measure the

part.

This option activates the functions G100, G103 and G104

(for probe movements) and probe canned cycles (which

help to measure part surfaces and to calibrate tools).

For the laser model, it only activates the non-cycle function

G100.

SOFT 60 CONV USER CYCLES

Conversational user cycles.

Incorporation of user cycles in conversational mode.

SOFT 60 PROGTL3

ProGTL3 programming language.

Another language apart from ISO for the programming of

profiles using a geometric language without the need to

use external CAD systems. This language allows for

program functions to define lines and circles which define

the points of intersection on a profile, in addition to macros

for the creation of solids defined by a flat profile and one

or more section profiles.

SOFT 60 PPTRANS

Part-program translator.

The program translator may be used to convert programs

written in other languages into Fagor ISO codes.

SOFT THIRD PARTY I/Os

Third-party CANopen.

Enables the use of non-Fagor CANopen modules.

SOFT MAB SYSTEM.

MAB drives.

Sercos connection with MAB drives.

SOFT 60 PWM CONTROL

Pulse-Width Modulation.

This function is only available for Sercos bus controlled

systems. It is mostly oriented toward laser machines for

the cutting of very thick sheets, where the CNC generates

a series of PWM pulses to control the power of the laser

when drilling the starting point.

This feature is essential for cutting very thick sheets and

it requires two quick digital outputs located on the central

unit. With this new feature, the OEM does not need to

install or program any external device, which reduces

machine costs and installation times. The end user also

benefits, since the “Cutting with PWM ” feature is much

easier to use and program.

SOFT 60 GAP CONTROL

Gap control.

This is mostly oriented toward laser machines. Gap

control makes it possible to maintain a set distance

between the laser nozzle and the surface of the sheet. This

distance is calculated by a sensor connected to the CNC,

so that the CNC offsets the sensor variations on the

distance programmed with additional movements in the

axis programmed for the gap.

SOFT DMC

Dynamic Machining Control.

DMC adapts the feedrate during machining to maintain the

cutting power as close as possible to ideal machining

conditions.

SOFT FMC

Fagor Machining Calculator.

The FMC application consists of a database of materials

to be machined and machining operations (milling and

turning) with an interface to choose suitable cutting

conditions for these operations.

SOFT FFC

Fagor Feed Control.

During the execution of a canned cycle of the editor, the

FFC function makes it possible to replace the feedrate and

speed programmed in the cycle with the active values of

the execution, which are acted upon by the feed override

and speed override.

SOFT 60/65/70 OPERATING TERMS

Temporary user license.

The "Operating Terms" option activates a temporary user

license for the CNC, which is valid until the date

determined by the OEM.

SOFT MANUAL NESTING

Manual nesting

Nesting consists of creating a pattern on the sheet material

using previously defined figures (in dxf, dwg or parametric

files), so as to use most of the sheet as possible. Once the

pattern has been defined, the CNC creates a program.

During manual nesting, the operator distributes the parts

on top of the sheet material.

Panel PC.

CNC 8060

CNC 8065

ꞏ8ꞏ

(REF: 2008)

SOFT AUTO NESTING

Automatic nesting

Nesting consists of creating a pattern on the sheet material

using previously defined figures (in dxf, dwg or parametric

files), so as to use most of the sheet as possible. Once the

pattern has been defined, the CNC creates a program.

During automatic nesting, the application distributes the

figures on the sheet material and optimizes the spaces.

Panel PC.

CNC 8060

CNC 8065

ꞏ9ꞏ

(REF: 2008)

ABOUT THE PRODUCT - CNC 8065

BASIC CHARACTERISTICS.

Basic characteristics. 8065 M 8065 M Power

Basic Pack 1 Basic Pack 1

Number of execution channels. 1 1 1 1 to 4

Number of axes. 3 to 6 5 to 8 5 to 12 8 to 28

Number of spindles. 1 1 to 2 1 to 4 1 to 4

Maximum number of axes and spindles. 7 10 16 32

Number of tool magazines. 1 1 1 to 2 1 to 4

Limited to 4 interpolated axes. Option Option Option Option

Basic characteristics. 8065 T 8065 T Power

Basic Pack 1 Basic Pack 1

Number of execution channels. 1 1 to 2 1 to 2 1 to 4

Number of axes. 3 to 5 5 to 7 5 to 12 8 to 28

Number of spindles. 2 2 3 to 4 3 to 4

Maximum number of axes and spindles. 7 9 16 32

Number of tool magazines. 1 1 to 2 1 to 2 1 to 4

Limited to 4 interpolated axes. Option Option Option Option

Basic characteristics. 8065 M 8065 M Power 8065 T 8065 T Power

Number of handwheels. 1 to 12

Type of servo system. Analog / Digital Sercos / Digital Mechatrolink

Communications. RS485 / RS422 / RS232

Ethernet

Integrated PLC.

PLC execution time.

Digital inputs / Digital outputs.

Marks / Registers.

Timers / Counters.

Symbols.

< 1ms/K

1024 / 1024

8192 / 1024

512 / 256

Unlimited

Block processing time. < 1 ms

Panel PC.

CNC 8060

CNC 8065

ꞏ10ꞏ

(REF: 2008)

(*) TTL / Differential TTL / Sinusoidal 1 Vpp / SSI protocol / FeeDat / EnDat

Remote modules. RIOW RIO5 RIOR RCS-S RIOW-E

Inline

Communication with the remote modules. CANopen CANopen CANopen Sercos EtherCAT

Digital inputs per module. 8 24 / 48 48 - - - 8

Digital outputs per module. 8 16 / 32 32 - - - 8

Analog inputs per module. 4 4 - - - - - - 4

Analog outputs per module. 4 4 - - - 4 2

Inputs for PT100 temperature sensors. 2 2 - - - - - - - - -

Feedback inputs. - - - - - - - - - 4 (*) - - -

Customizing (on an open system only).

PC-based open system, fully customizable.

INI configuration files.

Tool for display configuration FGUIM.

Visual Basic®, Visual C++®, etc.

Internal databases in Microsoft® Access.

OPC compatible interface

Panel PC.

CNC 8060

CNC 8065

ꞏ11ꞏ

(REF: 2008)

SOFTWARE OPTIONS.

Some of the features described in this manual are dependent on the acquired software options. The active

software options for the CNC can be consulted in the diagnostics mode (accessible from the task window

by pressing [CTRL] [A]), under software options.

Consult the ordering handbook for information on the software options available for your model.

SOFT ADDIT AXES

Additional shaft.

Add axes to the default configuration.

SOFT ADDIT SPINDLES

Additional spindle.

Add spindles to the default configuration.

SOFT ADDIT TOOL MAGAZ

Additional tool magazine.

Add tool magazines to the default configuration.

SOFT ADDIT CHANNELS

Additional channel.

Add channels to the default configuration.

SOFT 4 AXES INTERPOLATION LIMIT

Limited to 4 interpolated axes.

It limits the number of axes to 4, where the CNC can also

interpolate these at the same time.

SOFT i4.0 CONNECTIVITY PACK

Industry 4.0.

This option allows for the use and capture of data using the

FSYS.

SOFT OPEN SYSTEM

Open system.

The CNC is a closed system that offers all the features

needed to machine parts. Nevertheless, at times there are

some customers who use third-party applications to take

measurements, perform statistics or other tasks apart

from machining a part.

This feature must be active when installing this type of

application, even if they are Office files. Once the

application has been installed, it is recommended to close

the CNC in order to prevent the operators from installing

other kinds of applications that could slow the system

down and affect the machining operations.

SOFT DIGITAL SERCOS

Sercos digital bus.

SOFT EDIT/SIMUL

EDISIMU mode (editing and simulation).

It allows for the editing, modification and simulation of a

part-program.

SOFT DUAL-PURPOSE (M-T)

Dual-purpose machine.

A dual-purpose machine allows for both milling and

turning cycles. On lathes with a Y axis, it allows making

pockets, bosses and even irregular pockets with islands

during milling cycles. Turning cycles can be used by

milling machines which have a rotary axis that functions

as a C axis.

SOFT IEC 61131 LANGUAGE

IEC 61131 language

IEC 61131 is a PLC programming language that is very

popular in alternative markets, which is slowly entering

into the machine-tool market. With this feature, the PLC

may be programmed either in the usual Fagor language

or in IEC 61131 format.

This feature requires the MP-PLUS (83700201)

processor.

SOFT TOOL RADIUS COMP

Compensación de radio.

Tool compensation allows programming the contour to be

machined based on part dimensions of the and without

taking into account the dimensions of the tool that will be

used later on. This avoids having to calculate and define

the tool path based on the tool radius.

SOFT IIP CONVERSATIONAL

Interactive Icon-based Pages (conversational mode).

IIP or conversational mode is specifically designed for

people without any prior programming knowledge or for

those that are not familiarized with Fagor CNC's.

Working in conversational mode is easier than in ISO

mode, as it ensures proper data entry and minimizes the

number of operations to be defined. There is no need to

work with part-programs.

Panel PC.

CNC 8060

CNC 8065

ꞏ12ꞏ

(REF: 2008)

SOFT PROFILE EDITOR

Profile editor.

Allows for the part profiles to be edited graphically and to

import dxf files.

SOFT HD GRAPHICS

HD graphics.

High definition solid 3D graphics for the execution and

simulation of part-programs and canned cycles of the

editor.

During machining, the HD graphics display, in real time,

the tool removing the material from the part, allowing the

condition of the part to be seen at all times. HD graphics

can display up to 4 views of the part, where each can be

rotated, zoomed in or zoomed out. Measurements can

also be made on the part and even sections on the piece

from any angle.

In a multi-channel system, this feature requires the MP-

PLUS (83700201) processor.

SOFT RTCP

Dynamic RTCP (Rotating Tool Center Point).

The dynamic RTCP option is required for interpolation

machining with 4, 5 or 6 axis.

This feature requires the MP-PLUS (83700201)

processor.

SOFT C AXIS

C axis.

It activates the kinematics for working with the C axis and

the associated canned cycles. The CNC can control

several C axes. The parameters of each axis indicate if it

will function as a C axis or not, where it will not be

necessary to activate another axis for the machine

parameters.

SOFT Y AXIS

Y axis for lathe.

It activates the kinematics for working with the Y axis and

the associated canned cycles.

SOFT TANDEM AXES

Tandem axes.

A tandem axis consists in two motors mechanically

coupled (slaved) and making up a single transmission

system (axis or spindle). A tandem axis helps provide the

necessary torque to move an axis when a single motor is

not capable of supplying enough torque to do it.

When activating this feature, it should be kept in mind that

for each tandem axis of the machine, another axis must be

added to the entire configuration. For example, on a large

3-axis lathe (X Z and tailstock), if the tailstock is a tandem

axis, the final purchase order for the machine must

indicate 4 axes.

SOFT SYNCHRONISM

Synchronization of axes and spindles.

The axes and ballscrews may be synchronized in two

ways: in terms of speed or position. The CNC

configuration takes into consideration the synchronization

of 2 axes or 2 spindles. Once synchronized, only the

master displays and programs the element.

SOFT KINEMATIC CALIBRATION

Kinematics calibration.

This work mode may be used to calibrate kinematics for

the first time and to re-calibrate it every so often to correct

any possible deviations originated by the day-to-day

machine work.

SOFT HSSA II MACHINING SYSTEM

HSSA-II machining system.

This is the new version of algorithms for high speed

machining (HSC). This new HSSA algorithm allows for

high speed machining optimization, where higher cutting

speeds, smoother contours, a better surface finishing and

greater precision are achieved.

SOFT TANGENTIAL CONTROL

Tangential control.

"Tangential Control" maintains a rotary axis always in the

same orientation with respect to the programmed tool

path. The machining path is defined on the axes of the

active plane and the CNC maintains the orientation of the

rotary axis along the entire tool path.

SOFT PROBE

Probing canned cycles.

The CNC may have two probes; usually a tabletop probe

to calibrate tools and a measuring probe to measure the

part.

This option activates the functions G100, G103 and G104

(for probe movements) and probe canned cycles (which

help to measure part surfaces and to calibrate tools).

SOFT CONV USER CYCLES

Conversational user cycles.

Incorporation of user cycles in conversational mode.

SOFT 70 PROGTL3

ProGTL3 programming language

Another language apart from ISO for the programming of

profiles using a geometric language without the need to

use external CAD systems. This language allows for

program functions to define lines and circles which define

the points of intersection on a profile, in addition to macros

for the creation of solids defined by a flat profile and one

or more section profiles.

SOFT PPTRANS

Part-program translator.

The program translator may be used to convert programs

written in other languages into Fagor ISO codes.

SOFT THIRD PARTY I/Os

Third-party CANopen.

Enables the use of non-Fagor CANopen modules.

SOFT FVC STANDARD

SOFT FVC UP TO 10m3

SOFT FVC MORE TO 10m3

Volumetric compensation.

5-axis machines are generally used during the

manufacturing of large parts. The accuracy of the parts is

limited by the machine manufacturing tolerances and is

effected by temperature variations during machining.

In sectors such as the aerospace industry, machining

demands mean that classic compensation tools are

becoming suboptimal. Volumetric compensation FVC

comes in to complement the machine adjusting tools.

When mapping the total work volume of the machine, the

CNC knows the exact position of the tool at all times. After

applying the required compensation, the resulting part is

made with the desired precision and tolerance.

There are 3 options, which depend on the size of the

machine.

• FVC STANDARD: 25-point compensation on each

axis. Quick calibration (time), but less precise than the

other two, but sufficient for the desired tolerances.

• FVC UP TO 10m3: Volume compensation up to 10 m³.

More accurate than FVC STANDARD, but requires a

more accurate calibration using a Tracer or Tracker

laser).

• FVC MORE TO 10m3: Volume compensation greater

than 10 m³. More accurate than FVC STANDARD, but

Panel PC.

CNC 8060

CNC 8065

ꞏ13ꞏ

(REF: 2008)

requires a more accurate calibration using a Tracer or

Tracker laser.

This feature is not available for the “Power” model.

SOFT DMC

Dynamic Machining Control.

DMC adapts the feedrate during machining to maintain the

cutting power as close as possible to ideal machining

conditions.

SOFT FMC

Fagor Machining Calculator.

The FMC application consists of a database of materials

to be machined and machining operations (milling and

turning) with an interface to choose suitable cutting

conditions for these operations.

SOFT FFC

Fagor Feed Control.

During the execution of a canned cycle of the editor, the

FFC function makes it possible to replace the feedrate and

speed programmed in the cycle with the active values of

the execution, which are acted upon by the feed override

and speed override.

SOFT 60/65/70 OPERATING TERMS

Temporary user license.

The "Operating Terms" option activates a temporary user

license for the CNC, which is valid until the date

determined by the OEM.

BLANK PAGE

ꞏ14ꞏ

Panel PC.

CNC 8060

CNC 8065

ꞏ15ꞏ

(REF: 2008)

DECLARATION OF CE CONFORMITY AND

WARRANTY CONDITIONS

DECLARATION OF CONFORMITY

The declaration of conformity for the CNC is available in the downloads section of FAGOR’S corporate

website. http://www.fagorautomation.com. (Type of file: Declaration of conformity).

WARRANTY TERMS

The warranty conditions for the CNC are available in the downloads section of FAGOR’s corporate website.

http://www.fagorautomation.com. (Type of file: General sales-warranty conditions.

BLANK PAGE

ꞏ16ꞏ

Panel PC.

CNC 8060

CNC 8065

ꞏ17ꞏ

(REF: 2008)

VERSION HISTORY - CNC 8060

Here is a list of the features added to each manual reference.

Ref. 2008

PPC-19 and PPC-21 available for CNC 8060.

BLANK PAGE

ꞏ18ꞏ

Panel PC.

CNC 8060

CNC 8065

ꞏ19ꞏ

(REF: 2008)

VERSION HISTORY - CNC 8065

Here is a list of the features added to each manual reference.

Ref. 1709

Ref. 1801

Ref. 1811

Ref. 2008

First version.

Corrected errors.

Technical characteristics of PPC-19.

• SO image: Windows 10.

Technical characteristics of PPC-21.

• Storage: 128 GB SSD

• SO image: Windows 10.

MON-21W-MULTITOUCH. Information about this monitor is in the hardware manual.

BLANK PAGE

ꞏ20ꞏ

Page is loading ...

Fagor CNC 8065 for lathes Owner's manual

This manual is also suitable for

Fagor CNC 8065 for lathes Owner's manual

Related papers

Other documents