Extron PMK 155 User manual

Type
User manual
1
PMK 155 • Installation Guide
The Extron PMK 155 Pole Mount Kit is a simple solution for mounting Extron devices and their external power supplies to a
projector pole. The PMK can be installed on a 1.5-inch pipe within a 4-inch space between the projector and the ceiling.
Any of the following devices can be mounted, along with their power
supply:
One 3-inch deep half-rack device
One 6-inch deep half-rack device
Two 3-inch deep quarter rack devices
Four 4.5-inch deep eighth rack devices
One MPA 401
ATTENTION:
The maximum load for the PMK 155 is 5 lbs (2.25kg).
La charge maximum pour le PMK 155 est 2,25 kg (5 lbs).
Only for use with Extron UL listed products.
À utiliser uniquement avec les produits d’Extron, certifiés UL.
Pipe Clamp
Mounting Plate
(4) Tie Wraps
(2) Hex Bolts
(2) Washers
(6) #4-40 Screws
Installation
ATTENTION:
All electrical installation should be performed by qualified personnel in accordance with local and national building
codes, fire and safety codes, and local and national electrical codes.
Toute installation électrique devrait être effectuée par un personnel qualifié, conformément aux codes du bâtiment, aux
codes incendie et sécurité, et aux codes électriques locaux et nationaux.
To install the PMK 155 (with a device) on a projector pole:
1. Place the plate on the base of the device and align holes in the plate
with the mounting holes in the device.
2. Secure the device to the plate with 4-40 screws.
ATTENTION:
Use only supplied screws to avoid damaging the
device.
Utilisez seulement les vis fournies pour ne pas
endommager l’appareil.
3. Attach the power supply to the underside of the mounting plate by
passing the supplied tie wraps under the power supply, through the
raised slots in the plate, and back over the power supply.
Ensure the tie wraps sit in the grooves on the power supply. Tighten
the ties until snug.
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
Power Supply
PMK 155
2
68-2283-01 Rev. B
10 20
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2012-2020 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
4. With the installed device on top, lift the plate up to the installation location on the projector pipe. Fit the pipe clamp around
the pipe and hold it against the flange on the mounting plate.
5. Insert the two hex bolts through the clamp holes and into the flange.
6. Level the plate and tighten the hex bolts firmly to secure it against the pipe.
Half Rack Device
Power Supply
POWER
12V
3A MAX
OUTPUT
100V
INPUTS
L
(MONO)
(MONO)
R
REMOTE
VOL/MUTE
MPA 401-100V
R
L
CLASS 2 WIRING
DO NOT GROUND
OR SHORT
SPEAKER OUTPUTS!
10V 50mA
US
LISTED
17TT
AUDIO/VIDEO
APPARATUS
®
MPA 401
7. Attach input and output cables to the mounted device and thread the cables through the access hole in the projector pipe to
the inputs and the display device. Use the remaining tie wraps for cable tidying.
CAUTION:
DO NOT thread the projector power cable through the boom arm or mounting pipe. Threading it through the arm or
the pipe violates national electrical regulations.
N’enfilez pas le câble d’alimentation du projecteur sur le support flexible ou le tuyau de montage. L’enfiler sur le
support ou le tuyau enfreint les réglementations électriques nationales.
8. Connect the power supply to an electrical outlet and turn on the device.
For conguration and operation of the attached devices, see the user guide for the specic device.
  • Page 1 1
  • Page 2 2

Extron PMK 155 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages