urban ambiance UQL2406 Installation guide

Type
Installation guide
1of2
Package Contents
B
A
G
H
Shade
x5
Mounting Screw
x4
Inner Backplate
x1
Fixture
Body
x1
Socket
Collar Tool
x1
I
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (5) LED G9 4.5W Bulbs
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
FSocket Collar
x5
CWall Anchor
x2
D
Self-tapping
Screws
x2
STEP 1 -Attach Inner Backplate to Outlet Box
A. Attach the Inner Backplate (A) onto your desired location and align
one set of holes on the Inner Backplate (A) to the mounting holes on
the Outlet Box. Using a pencil, make (2) marks on the wall from (2)
keyholes on the Inner Backplate (A).
B. Remove the Inner Backplate (A). Drill proper holes from the marks
on the wall for Wall Anchors (C).
C. Insert Wall Anchors (C) into drilled holes on the wall. Attach the
Inner Backplate (A) back onto the outlet box and secure the with
Outlet Box Screw
(not Supplied)
A
D
C
Supply Wires and
Ground Wire
Outlet Box
Figure 1
outlet box screws (not supplied) and
Self-tapping Screws (D). Tighten until
snug.
Keyhole
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Figure 2
STEP 3 Install Fixture Body-
A. Place the backplate of the Fixture Body (H) onto the Inner Backplate
(A). Line up holes on the top and bottom of the backplate and the
mounting holes on the top and bottom of the Inner Backplate (A).
Secure them together by threading Mounting Screws (B) into the
mounting holes on the Inner Backplate (A). Hand tighten until snug.
Figure 3
B
H
A
STEP 4 Install Shade-
A. Place Shades (G) over Sockets as shown.
By using the Socket Collar Tool (I), thread
Socket Collars (F) onto sockets to secure
Shades (G). Hand tighten until snug.
Figure 4
Socket
G
F
I
Installation Instructions: UQL2406
www.urbanambiance.com
2of2
SKU: UQL2406
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
NO. QTY.
PART NUMBER REPLACEMENT PART DESCRIPTION
1
5
2
5
UQL2406SH SHADE
UQL2406LED BULB 4.5W LED G9 DIM WHITE
1
2
STEP 5 Install Bulb-
A.
Your fixture is now assembled and ready to use. Enjoy!
Install the G9 bulbs as specified (not provided).
This fixture is rated to use 50W maximum G9 Xenon bulbs. You may use a lower wattage
G9 Xenon or if you purchased the LED model it is supplied with G9 LED bulbs.
Note:
E
Figure 5
6” 5”
6.25”
3.25”
4.25”
42”
3”
3”
18”
(5) 4.5W Maximum
LED G9 Bulbs
www.urbanambiance.com
  • Page 1 1
  • Page 2 2

urban ambiance UQL2406 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI